Aluminum Ergonomic Gas Spring Desk Mount - Dual

Important Safety Information and Warnings

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

• Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

MAINTENANCE: Check that the bracket is secure and safe to use at regular intervals (at least every three months). AVLT-Power recommends checking the mounting screws every two months for tightness.

Product Specifications

• Supports monitors up to 32 inches.
• VESA mounting patterns: 75x75mm and 100x100mm.
• Weight capacity: 1-8kg (2.2-17.6lbs) per arm.
• Gas spring mechanism for easy adjustment.

Parts List

Assembly Instructions

Step 1: Desk Mounting Options

Choose one of the following mounting methods:

Option 1a: Clamp Mount

1a-1a: Attach the clamp (C) to the desk edge. Ensure it is securely fastened.

1a-2: Connect the pole (A) to the clamp assembly. Tighten the adjustment knob [⚙️] to secure the pole.

1a-3: Attach the first arm segment (D) to the top of the pole. Use the provided screws and tighten.

Option 1b: Grommet Mount

1b-1a: Insert the grommet bolt through the desk hole and attach the clamp base.

1b-1b: Secure the base with nuts and washers.

Option 2: Base Plate Mount

2b-1: Attach the clamp (C) to the desk edge.

2b-2: Connect the pole (A) to the clamp assembly. Tighten the adjustment knob [⚙️].

Note: Diagrams 2b-1 and 2b-2 show alternative base plate attachments, likely involving screwing the base directly to the desk surface using the base plate (B) and screws.

Step 2: Assembling the Arms

Step 3: Attach the main arm (D) to the pole (A). Secure with the appropriate screws.

Step 4: Connect the second arm segment (D) to the first arm segment. Ensure proper alignment and secure with screws.

Step 5: Attach the VESA plate (G) to the end of the arm assembly. Use the provided screws (e.g., M4x12, H) and washers (D5) for a secure fit [✔️].

Step 3: Attaching the Monitor

Step 6: Align the monitor's VESA mounting holes with the VESA plate (G) on the arm. Use the appropriate screws (e.g., M5x12, L or M5x16, M-A through M-F, depending on monitor thickness) and washers (D5) to attach the monitor securely to the VESA plate. Ensure the monitor is oriented correctly.

Step 7 & 8: These diagrams illustrate the process of attaching the monitor to the VESA plate, showing different screw options and the final connection.

Step 4: Adjustments and Final Setup

Step 9: Adjust the gas spring tension using the provided Allen wrench (e.g., 4mm, I). Turn the adjustment screw to match the weight of your monitor, allowing for smooth vertical movement [?️].

Step 10: The final diagram shows the fully assembled mount with a monitor, illustrating the range of motion (tilt ±180°, ±135°, +35°, ±90°, -35°, ±180°) and the gas spring arm in action.