MiBoxer 2 Wires 2 in 1 LED Controller (2.4G) Instruction Manual

Product Features

The product utilizes the widely adopted 2.4GHz wireless technology, offering low power consumption, long signal transmission range, and strong anti-interference capabilities. It features an auto-transmitting function and is commonly used for controlling hotel and home lighting.

• ?️ Color temperature adjustable
• ☀️ Dim brightness
• ? 2.4G RF wireless transmission technology
• ? Remote control distance up to 30m
• ? Auto transmitting
• ? Support Smartphone app control (requires a 2.4GHz gateway)
• ? Support third-party voice control (requires a 2.4GHz gateway)

Set Up Output Mode

Configure the correct output mode based on the lighting features. Setting method: Press the "SET" button continuously to cycle through output modes. Note: The system will exit without saving if no operation is performed within 3 seconds.

Output Mode Sheet

Connect to LED Strip Diagram

Controller input voltage must match the required voltage of the LED strips.

Input: DC12V~48V

Single Color Modes: Diagram shows input terminals labeled V- and V+ (DC12V~48V), output terminals labeled LED V+ and LED V-, and a connection for a PUSH switch.

Dual White Modes: Diagram shows input terminals labeled V- and V+ (DC12V~48V), output terminals labeled LED V+, LED V-, CW, WW, and a connection for a PUSH switch.

2.4G RF Remote Control Instructions

1. Linking Code Instructions

1. Power off the device for 10 seconds, then power it on again. Alternatively, short press the "SET" button once, or turn on the light via the PUSH switch.
2. Short press the "I" button 3 times within 3 seconds.
3. The lights blinking 3 times slowly indicates successful linking.

Linking failed if the light does not blink slowly. Please repeat the steps. Note: Lights that have already been linked cannot be linked again.

2. Unlinking Code Instructions

1. Power off the device for 10 seconds, then power it on again. Alternatively, short press the "SET" button once, or turn on the light via the PUSH switch.
2. Short press the "I" button 5 times within 3 seconds.
3. The lights blinking 10 times quickly indicates successful unlinking.

Unlinking failed if the light does not blink quickly. Please repeat the steps. Note: Lights that have not been linked do not require unlinking.

Compatibility with 2.4G RF Remote Controls

The following 2.4G RF remote controls are compatible (purchased separately):

FUT006, FUT007, B1 / B1-B / T1, B2 / T2, K1 / K1-B, FUT087, FUT087-B, S1-B / S1-W, S1-G, WL-Box1.

4. Auto Transmitting (2.4G RF Remote Signal)

The controller can transmit remote signals to other controllers automatically. The effective distance between controllers for transmission is 30m, making the overall remote control distance unlimited. Attention: All controllers must be linked to the same remote.

Illustration: A signal icon is shown, followed by "Light", then "Distance 30m", then another "Light", and ellipses indicating continuation.

5. PWM High Frequency / Low Frequency Switching

Switch to High Frequency (16KHz):

Press the "OFF" button once within three seconds, then press the "ON" button 5 times. Activation is confirmed when the LED light flashes twice quickly.

Switch to Low Frequency (250Hz):

Press the "ON" button once within three seconds, then press the "OFF" button 5 times. Activation is confirmed when the LED light flashes twice slowly.

6. "Do Not Disturb" Mode Activation and Shutdown

This mode is useful in areas prone to power failures, helping to save energy.

Turn On "Do Not Disturb" Mode:

Press the "OFF" button three times within three seconds, then press the "ON" button three times. Activation is confirmed when the LED light flashes four times quickly.

Attention: "Do Not Disturb" mode activation status:

1. When the light is OFF: After activation, the light will remain OFF even after a power cycle (e.g., using the app or remote to turn it off). The user must turn the power off and on twice, or use the APP/remote to activate the light to restore normal operation.
2. When the light is ON: After activation, the light will turn OFF when the power is cycled once.

Turn Off "Do Not Disturb" Mode:

Press the "ON" button three times within three seconds, then press the "OFF" button three times. Deactivation is confirmed when the LED light flashes four times slowly.

Attention: If the power is cycled once after closing "Do Not Disturb" mode, the light will remain in the "ON" status.

PUSH Dimming

Short Press PUSH Switch:

Turns the light ON/OFF.

Long Press PUSH Switch:

Provides stepless dimming brightness. Long press and release your finger, then repeat long pressing to increase or decrease brightness.

[PUSH button diagram]

Attention

1. Please turn off the power supply before installation.
2. Please ensure the input voltage is the same as the device requirements.
3. Do not disassemble the device if you are not an expert, as it may cause damage.
4. Avoid using the light in areas with large metal surfaces or strong electromagnetic waves nearby, as this can seriously affect the remote control distance.

Scan the QR code to watch the 2.4GHz series video instruction or enter the following link directly: https://miboxer.com/light/video/1pc_remote.html

Made in China