DIAMOND CORE DRILLS STAND

Product Overview

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

• [See Instructions]
• [Eye Protection]
• [Protective Gloves]
• [Safety Footwear]
• [Protective Clothing]
• [Ear Protection]
• [Mask]

• ✔️ Only use on firm, level, unobstructed surfaces which are capable of supporting the stand and drill.
• ✔️ Ensure stand is fixed to surface capable of supporting stand, drill and work piece.
• ✔️ Replace or repair damaged parts. Use only recommended parts. Unauthorised parts may be dangerous and will invalidate the warranty.

WARNING! Failure to comply with these instructions may result in damage to the stand or other property and/or personal injury.

WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.

2. INTRODUCTION

Lightweight aluminium diamond core drill stand features tilting mechanism and base plate with anchor fitting. Handle and wheels for ease of transport. Ideal for use with Model No's DCD110V and DCD230V Diamond Core Drills.

3. SPECIFICATION

• Maximum Drill Bit Diameter: Ø200mm
• Travel Length: 600mm

4. OPERATION

4.1. ATTACHING DRILL TO STAND REF. FIG 1

1. The drill is attached to the stand using the drill clamp (fig.1).
2. Remove one half of the drill clamp by means of the screws, slot the drill into place and replace the clamp.
3. Secure the clamp by using the two locking handles.

4.2. SECURING STAND TO THE GROUND

1. To bolt the stand to the ground, drill a hole for a securing bolt a suitable distance away from your intended drilling area.
2. Note: You do have some adjustment on the drill base but plan before you drill.
3. The base can be levelled using the 4 levelling bolts. Adjust these before securing the anchor bolt.

4.3. SETTING THE ANGLE

1. Loosen the angle adjustment bolt and the brace locking handle, slide up or down until you get the desired angle.

Diagram Description (Fig. 1)

Figure 1 illustrates the components for attaching and securing the drill to the stand. Key parts include:

• Drill Cradle: The main support structure for the drill.
• Drill Clamp: Secures the drill motor into the cradle. It consists of two halves, typically attached or secured with screws.
• Raising and Lowering Handle: A lever used to adjust the vertical position of the drill.
• Cradle Locking Screw: Used to fix the drill cradle at a specific height.
• Locking Handles: Two handles used to secure the drill clamp.
• Brace Locking Point and Handle: A mechanism to lock the angle adjustment brace.
• Leveling Bolts: Four adjustable bolts on the base of the stand to ensure it is level on uneven surfaces.
• Anchor Bolt Channel: A channel or hole in the base plate for inserting an anchor bolt to secure the stand to the ground.
• Spirit Level: A small level indicator to help in setting up the stand accurately.
• Angle Adjustment Bolt: A bolt that, when loosened, allows the angle of the drill column to be adjusted.

5. MAINTENANCE

5.1. Keep clean, remove the spatter from the cradle guide channels.

6. TROUBLESHOOTING

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Notes and Warranty

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Contact Information

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

Phone: 01284 757500 | Fax: 01284 703534 | Email: sales@sealey.co.uk | Website: www.sealey.co.uk