User Manual for Jaycar models including: TL4582 High Temperature PLA 3D Pen Kit, TL4582, High Temperature PLA 3D Pen Kit, Temperature PLA 3D Pen Kit, PLA 3D Pen Kit, Pen Kit
Protech High Temp PLA 3D Pen Kit | Jaycar Australia
High Temperature PLA/ABS 3D Pen Kit HOBBYIST User Manual TL4582 WARNING · This pen is suitable for children over 8 years old and adults. Children are only allowed to use the pen under adult supervision. · The nozzle operates at high temperature, do not touch it while in operation. · It is strictly prohibited to use any other material into the filament loading hole. · Do not use power adapters other than the one provided in the kit. · Prohibited to use filament provided by other company, with different filament parameters. · Keep the pen away from water. · Keep the pen in a safe place, out of reach of children. PACKAGE CONTENTS · Type-C Adapter · Filaments · User Manual · 3D Pen · Plastic Screw Driver (for adjusting temperature and opening the back cover) 2 FUNCTIONS Type-C Socket OLED Screen Temperature Up Temperature Down Speed Controller Filament loading hole Unload Filament Button Load Filament Button Nozzle 3 OPERATING INSTRUCTIONS 1. Plug in the Type-C adapter or to a power bank which has an output of 2A or above. 2. Click the filament loading button once to start heating. When the actual temperature reaches the preset temperature, the pen is ready to work. 3. Put the filament in through the filament loading hole. Keep pressing or double click the filament loading button to load the filament. 4 4. The buttons marked as "+" and "-" are used for temperature adjustment. The scope is 130ºC to 230ºC. The slide button is used for speed adjusment. Up is faster and down is slower. 5. Keep pressing or double clicking the filament unload button to unload the filament. Clicking the "+" and filament unloading button at the same time enables you to switch the temperature to fit either ABS or PLA. 6. The pen will enter standby mode after 2 minutes of no operation. Click the filament loading button to start heating the pen. Please do not touch the tip of the pen. 5 TROUBLESHOOTING ISSUE REASON SOLUTION The power indicator light does not flash The power adapter or plug line defective Repair or replace the power adapter Motherboard defective Repair or replace the motherboard Socket lead off Solder the socket No filament come out of nozzle Nozzle blocked Temperature is not high enough Replace the nozzle set Replace the nozzle set or adjust the temperature No working temperature Replace the nozzle set or check the motherboard Gear slips Move out filament, clean gear, cut off Fail to load filament the damaged filament, then reload it Unload filament and cut the end of filament well Motherboard defective Repair or replace the motherboard No working temperature Heating part defective Replace the nozzle set 6 FILAMENT CUT Correct Wrong Wrong SPECIFICATIONS Discharging mode: Molding: Print Range: Feeding Speed: Printing Material: Electric Parameter: Nozzle Diameter: Filament Diameter: Filament Temperature: Power Adapter: Pen Dimensions: Pen Net Weight: Hot melt extrusion molding Three-dimensional molding Unlimited Adjustable PLA/ABS DC5V 2A 10W 0.7mm 1.75mm ABS 220ºC, PLA 190ºC 100-240V 50/60Hz 0.5A 175mm x 17mm x 20mm 46g 7 WARRANTY INFORMATION Our product is guaranteed to be free from manufacturing defects for a period of 12 Months. If your product becomes defective during this period, Electus Distribution will repair, replace, or refund where a product is faulty; or not fit for intended purpose. This warranty will not cover modified product; misuse or abuse of the product contrary to user instructions or packaging label; change of mind and normal wear and tear. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and failure does not amount to a major failure. To claim warranty, please contact the place of purchase. You will need to show receipt or other proof of purchase. Additional information may be required to process your claim. Any expenses relating to the return of your product to the store will normally have to be paid by you. The benefits to the customer given by this warranty are in addition to other rights and remedies of the Australian Consumer Law in relation to the goods or services to which this warranty relates. This warranty is provided by: Electus Distribution Address 46 Eastern Creek Drive, Eastern Creek NSW 2766 Ph. 1300 738 555Adobe PDF Library 17.0 Adobe InDesign 20.0 (Macintosh)