EcoFlow STREAM Ultra/Pro

About This Manual

• Applicable Product Models: EcoFlow STREAM Ultra, EcoFlow STREAM Pro
• This manual provides an introduction to the product, its operation, management, and maintenance. It may be updated without prior notice.
• The availability of certain accessories and features may vary by country or region.
• All images in this manual are for demonstration purposes only. Refer to the actual product received. The EcoFlow STREAM Ultra is used as the example product.
• For PDF readers, you can find the latest updates online at https://www.ecoflow.com/support/download/index.

Overview

The EcoFlow STREAM Ultra / EcoFlow STREAM Pro (hereinafter referred to as "the device") is a solar power storage system designed for both new installations and retrofits of existing solar power supply systems. The device features connections for solar input, grid connection, parallel connection, and two standard AC outlets. Internally, it integrates an inverter, MPPT charge controller, and battery modules to enable efficient energy storage and management.

Appearance

1. Grip Recess: Used for safely lifting and moving the device.

2. Protective Cover: Covers electrical connections and outlets to protect against dust, moisture, and accidental contact.

3. Grounding Terminal: Provides an additional grounding connection.

4. DIY Front Casing: Used to maintain the original appearance. DIY replacement casings are available for purchase.

5. Power Button: Used to turn the device on/off and reset IoT settings.

6. System Status LED: Indicates the current operating status of the device.

7. Parallel Terminal: Used to connect multiple units for system expansion, inter-unit communication, and increased AC outlet output.

8. AC Outlets: Used to power connected devices or connect to a micro-inverter for additional power input.

9. AC ON/OFF Button: Activates or deactivates the AC outlets.

10. Grid Connection: Connects the device to the grid for feeding power into or drawing power from the grid.

11. PV Terminals: Connects solar panels for power supply.

+ The actual appearance of the AC outlet may vary depending on the sales region and product version.

* The STREAM Ultra has 4 pairs of PV terminals, while the STREAM Pro has 3 pairs.

Power Button

The button has the following functions:

• Power On: Press and hold the button for 2 seconds to turn on the device.
• Power Off: Press and hold the button for 2 seconds to turn off the device. If solar or grid power is present, disconnect the cables before turning off.
• Reset IoT: Press the button 5 times consecutively to reset Wi-Fi and Bluetooth connections. Resetting IoT settings disconnects the device from your EcoFlow account.

AC ON/OFF Button

This button has the following functions:

• AC On: When the outlets are deactivated, press once to activate the AC outlets.
• AC Off: When the outlets are activated, press once to deactivate the AC outlets.

LED Indicator

System Status LED:

• The following LED pattern indicates the device is turned off.
• The following LED patterns indicate the current battery charge level of the device.
• The following LED pattern indicates the device is charging.
• The following LED pattern indicates the device is faulty. Refer to the EcoFlow App for further instructions.
• The following LED pattern indicates a setting has been applied, e.g., a system reset or completion of internet setup.
• The following LED pattern indicates the device is updating its firmware.

AC Outlet Status LED:

• The following LED pattern indicates at least one AC outlet is activated.
• The following LED pattern indicates AC outlets are deactivated.

Expand Power Source

The AC outlets of the device support bidirectional power flow for charging and discharging. Adding a micro-inverter increases input capacity and improves overall charging efficiency.

How to Connect a Micro-Inverter

1. Prerequisite: Ensure your micro-inverter supports direct plug-in with a standard AC outlet and complies with local regulations. EcoFlow micro-inverters are preferred; third-party models may require additional measures.
2. After connecting the micro-inverter to solar panels, plug the AC output cable directly into the device's AC outlet.
3. Press the AC ON/OFF button on the device once to activate the outlet.

How to Remove a Micro-Inverter

1. Press the AC ON/OFF button on the device once to deactivate the outlet.
2. Unplug the micro-inverter's AC output cable from the device's AC outlet.

EcoFlow recommends integrating only ONE micro-inverter into your STREAM system.

System Expansion

Method 1: Cascaded Single-Room Configuration

This configuration connects multiple STREAM devices in a single room to expand system capacity using a daisy-chain layout. Devices are connected via parallel cables and share a common grid input. The device directly connected to the grid acts as the master unit, while others function as slave units within the cascade, participating in power supply and control.

How to Connect a Cascaded System in Parallel

1. Ensure all STREAM devices are powered off. If grid or solar connections are present, disconnect the cables, then press and hold the power button for 2 seconds to turn off the device.
2. Plug the EcoFlow STREAM Parallel Cable into the parallel terminal and the grid terminal between STREAM devices, tightening the screws on both ends. If you have multiple devices, repeat this step until a grid connection (usually on the first unit) and a parallel connection (usually on the last unit) remain unused in the connection chain.
3. Connect the EcoFlow STREAM AC Cable to the grid connection and the grid of the first STREAM device, tightening the screw on the connector. This device is considered the master unit, while the others are slave units.
4. Tip: Once connected to an active power source, STREAM devices will power on automatically.
5. Open the EcoFlow App to bind the STREAM devices to your account. Ensure all devices are connected to the same Wi-Fi network.

How to Remove a Cascade System

1. Turn off and disconnect the connected devices.
2. Disconnect the master unit from the grid and all devices from a solar input. If either the grid or solar connection is present, powering off the devices will not be effective.
3. Press and hold the power button for 2 seconds to turn off each device.
4. Loosen the screws on both ends of the parallel cable to detach the connectors. Then, turn the connector counter-clockwise to remove the cable.
5. Open the EcoFlow App and disconnect the devices from your account as needed.

Notes:

• Parallel connection should only be performed when the master unit is disconnected from the grid.
• In case of grid connection failure, parallel units cannot function as a system and will operate independently.
• The standard protective cap should be fitted on any unused terminal.
• Up to 6 STREAM devices can be installed in a system. Cascaded and distributed configurations can be freely combined within this limit.

Method 2: Distributed Configuration for Multiple Rooms

This setup is permissible only if local electrical regulations allow direct plugging of the device into a household outlet. This configuration allows for the installation of STREAM devices in different rooms, offering flexible placement throughout the house. Each device connects individually to a wall outlet on the same circuit, while simultaneously sharing battery resources across the entire system. Synchronized energy management and communication are enabled by the existing home wiring and Wi-Fi, eliminating the need for physical parallel wiring.

How to Install a Distributed System

1. Connect the EcoFlow STREAM AC cable to the grid connection of a STREAM device to an outlet, then tighten the screw on the connector. Tip: Once connected to an active power source, STREAM devices will power on automatically.
2. Connect additional STREAM devices separately in the rooms where you wish to place them.
3. Open the EcoFlow App to bind the STREAM devices to your account. Ensure all devices are connected to the same Wi-Fi network.

How to Remove a Distributed System

1. Turn off and disconnect the connected devices.
2. Disconnect all STREAM devices from the grid and from any solar input. If either is connected, powering off the devices will not be effective.
3. Press and hold the power button for 2 seconds to turn off each device.
4. Move or store the devices as needed.
5. Open the EcoFlow App and disconnect the devices from your account as needed.

Notes:

• The standard protective cap should be fitted on any unused terminal.
• Up to 6 STREAM devices can be installed in a system. Cascaded and distributed configurations can be freely combined within this limit.

System Planning

The STREAM device supports a basic power planning scheme. Without an integrated Smart Sensor, the feed-in power cannot be adjusted in real-time to household power consumption. Instead, it can only be manually set to a fixed power or scheduled for specific periods via the EcoFlow App. Intelligent sensor integration enhances planning capabilities.

Flexible Planning with Smart Plug

A Smart Plug allows you to manage when devices are turned on or off via the EcoFlow App, offering more flexibility in physical placement. Once integrated into the system, STREAM devices will adjust feed-in power based on the total load of devices connected to the Smart Plug, prioritizing their power supply and backup resources.

How to Add a Smart Plug

Follow the Smart Plug's user manual to complete the installation. Ensure the plug is connected to the same wireless network as the STREAM system.

How to Remove a Smart Plug

1. Turn off the connected devices and unplug them from the outlet.
2. Move or store the Smart Plug as needed.
3. Open the EcoFlow App and remove the Smart Plug from the STREAM system if necessary.

Compatible Plug Models:

• EcoFlow × Shelly Smart Plug (up to 6 units)
• EcoFlow Smart Plug (up to 16 units)
• You can mix different plug models for up to 22 integrated plugs in a STREAM system.
• Only one sensor type can be added at a time. Installing both a Smart Plug and a Smart Meter may lead to redundant data usage or sensor inefficiency, as the system can only operate in one planning mode.

Whole-Home Planning with Smart Meter

A Smart Meter acts as a household sensor, measuring the difference between power drawn from the grid and power fed into it. The STREAM system uses this data to adjust feed-in power based on the total household load, ensuring efficient and balanced energy distribution across all connected STREAM devices.

How to Install a Smart Meter

Have a qualified electrician install the Smart Meter in your home's distribution box. Ensure it is connected to the same Wi-Fi network and bound to the same EcoFlow account as the STREAM system.

How to Remove a Smart Meter

1. Contact a qualified electrician to remove the Smart Meter.
2. Open the EcoFlow App and remove the Smart Meter from the STREAM system if necessary.

Compatible Meter Models:

• EcoFlow × Shelly Smart Meter
• EcoFlow Smart Meter
• Shelly 3em
• Shelly Pro 3em
• Tibber Pulse IR
• Only 1 Smart Meter is needed for a STREAM system.
• Only one sensor should be added to the system at a time. Installing both a Smart Plug and a Smart Meter may lead to redundant data usage or sensor inefficiency, as the system can only operate in one planning mode.

Storage and Maintenance

Routine Maintenance

Perform routine maintenance as follows:

1. Wipe the product surface with a soft, dry cloth and keep it clean.
2. Every 6 months, check that all connection components are in good condition.
3. If the device will not be used for an extended period, charge and discharge the product every 3 months (fully charge, then discharge to 60% for storage) to maintain battery health. AC charging from the grid is the most recommended option in this case:
   • In the EcoFlow App, set the backup reserve level to 100% and fully charge the device.
   • After charging, set the reserve level to 60% to begin discharging for storage.

Maintenance of User-Replaceable Parts

Removing the Product

Before performing repairs, follow these steps to remove the device:

1. Deactivate the AC outlets: Press the AC ON/OFF button once to turn off the outlets. Then, disconnect the device and the micro-inverter.
2. Disconnect from the grid: Unscrew and firmly pull the connector at the device's grid terminal. Turn the locking ring on the connector counter-clockwise to unplug the cable.
3. Disconnect the cascaded STREAM device (if applicable): Unscrew the connector at the device's parallel terminal. Turn the locking ring on the connector counter-clockwise to unplug the cable. Repeat this step if you have multiple units connected in parallel.
4. Disconnect Solar: Use the included solar wrench to disconnect the solar cables from the PV terminal.
5. Disconnect from the grid: Unscrew and firmly pull the connector at the device's grid terminal. Turn the locking ring on the connector counter-clockwise to unplug the cable.
6. Remove the device (if applicable): Unscrew the device from the mounting and locking brackets.
7. Disposal (Optional): If the system no longer functions, dispose of it according to local regulations for electronic devices.

Replacing the DIY Front Casing

Tool Requirements:

• Phillips screwdriver (e.g., SL3) or other suitable tool
• Protective gloves (optional)

Steps:

1. Disconnect all cables and remove the retaining brackets (if applicable). Press and hold the power button for 2 seconds to turn it off, then place it upright.
2. Pry the clips outward with a screwdriver to release them, then remove the front casing.
3. Pull the front casing downwards to release it from the slots, then remove the old front casing.
4. Adjust the device's position so the front cover side faces up. Slide the new front casing into the groove from the side near the IoT module and align it with the 4 grooves to secure it. The mounting of the new front casing is then complete.

Replacing the IoT Module

Prerequisites:

• Always contact EcoFlow technical support before attempting to replace the IoT module. Perform the following steps only after receiving the replacement module from EcoFlow.

Tool Requirements:

• Phillips screwdriver (e.g., SL3) or other suitable tool
• PH1 screwdriver
• Anti-static gloves

Steps:

1. Disconnect all cables and remove the retaining brackets (if applicable). Press and hold the power button for 2 seconds to turn it off, then place it upright.
2. Pry the clips outward with a screwdriver to release them, then remove the front casing.
3. Locate the IoT module and remove its mounting screws using a PH1 screwdriver (screw specification: M3).
4. Carefully lift the circuit board to expose the power cable underneath. Press the white latch and pull the cable out.
5. Pull the signal cable directly out of the circuit board to completely remove the old IoT module.
6. Connect the power and signal cables to the new IoT module and place them in the correct position (avoid pinching the cables).
7. Reinstall the IoT protective cover and tighten the screws.
8. Reinstall the device's front casing.

Long-Term Storage

For long-term storage, place the device in a dry and tidy location in its original packaging. Protect all components to prevent strong moisture, impacts, vibrations, etc. The product should be stored at temperatures between –40 °C and +85 °C, with 25 °C being the optimal storage temperature.

Troubleshooting

The device's LED provides a basic indication to check the operating status. If you notice an abnormal LED pattern, refer to the in-app troubleshooting guide.

The following LED pattern indicates the device is faulty. Refer to the EcoFlow App for further instructions.

If you cannot access the EcoFlow App, contact EcoFlow customer service. Do not attempt to repair this product without official instructions from the support team.

Safety Information and Regulatory Compliance

Disclaimer

Please read the product documentation and ensure you fully understand it before using the product. Improper use can lead to serious injury, damage, or loss of property. Always refer to the latest documentation at https://www.ecoflow.com/support/download/. This documentation takes precedence over all other versions.

By using this product, you acknowledge and agree to all terms mentioned in the documentation. EcoFlow is not liable for damages resulting from improper use or failure to follow the provided instructions. In accordance with applicable laws and regulations, EcoFlow reserves the right of legal interpretation of this document and all related product documents.

Safety Symbols

Safety symbols on the device's casing or nameplate indicate potential hazards. Please refer to the following table for these symbols and their meanings:

• Caution: Disconnect the device from all power sources before performing maintenance.
• Caution! Risk of Electric Shock: Do not attempt to disassemble the device. No user-serviceable parts inside. Leave servicing to qualified service personnel.
• Caution! Hot Surface: Do not touch the device's casing during operation.
• Caution! Risk of Electric Shock: Wait at least 5 minutes after all power sources have been switched off before performing maintenance.
• Read Manual: Carefully read the user manual and all safety instructions before installation, operation, and maintenance.
• CE Marking: The device complies with the essential requirements of the relevant EU legislation.
• WEEE Directive: Do not dispose of the device with household waste. Follow local regulations for electronic waste disposal.
• Grounding: Indicates the connection point for the protective earth cable (PE).

Safety Instructions

1. Read this document and other related product documentation before operating the device.
2. This product must be used in accordance with applicable local electrical safety regulations and specific operating conditions. Damage due to causes outside of product quality or improper use – including, but not limited to, short circuits caused by electrical devices or operating environments – is not covered by the warranty.
3. An overcurrent protection switch must be installed between this product and the grid.
4. When the photovoltaic system (PV) receives light, it supplies voltage to the power conversion equipment (PCE).
5. When installing and maintaining this product, use insulated tools and wear personal protective equipment.
6. Install this product in a dry and well-ventilated environment.
7. Keep this product out of the reach of children and pets. If the product is used near children, they must be carefully supervised.
8. Ensure the cable length for each PV connection to this product is less than 3 meters.
9. Before making electrical connections, ensure all loads to be connected (e.g., devices or equipment to be powered by this product) are turned off.
10. Always pull the plug, not the cable, when disconnecting the product from the power source to reduce the risk of damage to the plug and cable.
11. Do not insert fingers or hands into the product.
12. Do not expose the product to direct sunlight, rain, or snow.
13. Do not expose the device to strong electromagnetic fields to avoid radio interference.
14. Do not install or operate the device near flammable, explosive, corrosive, caustic, or humid sources.
15. Do not install or operate this device in extreme weather conditions such as lightning, heavy rain, or strong winds.
16. Protect this product from strong impacts, vibrations, and falls.
17. Do not pull, crush, step on, or throw this device into a fire, as it may explode.
18. Do not use damaged cables with this product.
19. Do not damage, deface, or remove any labels on this product.
20. Do not disassemble, repair, or modify this product yourself. Contact EcoFlow customer service for any maintenance or service work.
21. Use only manufacturer-approved or recommended components and accessories. If you need replacement parts, contact EcoFlow customer service.
22. Do not clean the product with flammable or toxic solvents. Wipe it with a dry, soft cloth.
23. Do not place heavy objects (>40 kg) on the product.
24. Removing the Device: To safely remove this product, follow these steps sequentially:
    • Turn off the connected loads.
    • Disconnect the cables from the AC outlets.
    • Disconnect the cable from the grid terminal.
    • Disconnect the cables from the PV terminals.
    • Turn off the product.
25. GROUNDING INSTRUCTIONS: This product must be grounded. In case of a fault or failure, grounding provides the path of least resistance for electrical current, reducing the risk of electric shock. For your safety, EcoFlow provides a cable with a device ground conductor and a ground plug. The plug must be inserted into an outlet that is properly installed and grounded in accordance with all local regulations and ordinances.
26. WARNING - Improper connection of the device ground conductor can result in electric shock. In the following cases, contact a qualified electrician instead of replacing the supplied plug:
    • You are unsure whether the product is properly grounded;
    • The supplied plug does not fit the outlet.
27. Personnel Requirements: Certain installation or maintenance tasks may only be performed by qualified personnel. Refer to the personnel requirements highlighted in the product documentation to ensure these tasks are performed correctly and safely.
28. Note on Floating Ground: The ground connection is not connected to the AC neutral line. The internal electrical system remains isolated from ground when the device (and its cascaded system, if applicable) is disconnected from the grid power supply.

Declarations of Conformity

Hereby, EcoFlow Inc. declares that this product complies with Directives 2014/35/EU, 2014/30/EU, 2014/53/EU, 2011/65/EU+(EU) 2015/863, (EU) 2023/1542. The full text of the EU declaration of conformity is available at the following internet address: http://www.ecoflow.com/eu/eu-compliance

Radio Frequency (RF) Specifications for the EU:

• Bluetooth:
  • Frequency: 2 402-2 480 MHz
  • Maximum output power: <20 dBm
• WLAN:
  • Frequency: 2 412-2 472 MHz / 2 422-2 462 MHz
  • Maximum output power: <20 dBm

This symbol indicates that this product must not be disposed of with household waste within the EU. Recycle this product properly to prevent possible harm to the environment or human health from uncontrolled waste disposal and to promote the sustainable reuse of material resources. Please return your used product to a suitable collection point or contact the retailer where you purchased the product. Your retailer will accept used products and send them for environmentally sound recycling.

For information on the disposal of electrical and electronic equipment, please visit the following website: https://eu.ecoflow.com/pages/electronic-devices-disposal

Appendix

Package Contents

• 1x EcoFlow STREAM Ultra / EcoFlow STREAM Pro
• n x EcoFlow STREAM Solar Panel Extension Cable (2.95 m)+
• 1x EcoFlow STREAM AC Cable (1.5 m) / 1x EcoFlow STREAM DIY Cable (1.5 m)*
• 1x PV Wrench
• 1x Mounting Bracket
• 1x Locking Bracket
• 4x M4*8 Screws
• 2x Expansion Bolts with Anchors

+ The STREAM Ultra comes with 8 PV cables, while the STREAM Pro comes with 6. This is determined by the number of PV connections on each unit.

* The actual appearance of the AC cable may vary depending on the sales region and product version.

Technical Specifications

EcoFlow STREAM Ultra

General Information

• Model: EF-EA-HD-U2K-800, EF-EA-HD-U2K-600
• Dimensions: 255 x 284 x 458 mm
• Net Weight: 23.1 kg
• Typology: Insulated
• IP Protection Rating: IP65
• Pollution Degree: PD3
• OVC Category: DC: II, AC: III
• Environmental Category: Indoor/Outdoor
• Cooling Method: Natural Convection (no fan)

Battery Information

• Rated Power: 1.92 kWh
• Rated Voltage: 19.2 V-
• Lifecycle: 6,000
• Cell Chemistry: LFP (LiFePO4)

PV Terminal (DC)

• Number of MPPTs: 4
• MPPT Voltage Range: 15-60 V-
• Max. Input Power: 2,000 W (500 W per MPPT)
• Max. Input Voltage: 60 V
• Max. Input Current: 14 A
• Max. Input Short Circuit Current: 20 A

Grid Terminal (AC)

• Rated Voltage and Frequency: 230 V~, 50 Hz
• Rated Output Power: EF-EA-HD-U2K-800: 800 W, EF-EA-HD-U2K-600: 600 W
• Rated Output Current: EF-EA-HD-U2K-800: 3.48 A, EF-EA-HD-U2K-600: 2.61 A
• Max. Input Current: 10 A
• Max. Input Power: 2,300 W
• Power Factor: 1 (-0.8 to +0.8)

AC Outlet (AC)

• Rated Voltage and Frequency: 230 V~, 50 Hz
• Max. Output Power: 1,200 W
• Max. Output Apparent Power: 1,200 VA
• Rated Output Current: 5.22 A
• Max. Output Current (Bypass Mode): 10 A
• Max. Input Power: EF-EA-HD-U2K-800: 800 W, EF-EA-HD-U2K-600: 600 W
• Max. Input Apparent Power: EF-EA-HD-U2K-800: 800 VA, EF-EA-HD-U2K-600: 600 VA
• Max. Input Current: EF-EA-HD-U2K-800: 3.48 A, EF-EA-HD-U2K-600: 2.61 A
• Power Factor: 1 (-0.8 to +0.8)

Parallel Terminal (AC)

• Rated Voltage and Frequency: 230 V~, 50 Hz
• Max. Output Power: 2,300 W
• Max. Output Apparent Power: 2,300 VA
• Max. Output Current: 10 A
• Max. Input Current: 10 A
• Max. Input Power: 2,300 W
• Max. Input Apparent Power: 2,300 VA
• Power Factor: 1 (-0.8 to +0.8)

Environment

• Operating Altitude: ≤ 4,000 m
• Operating Temperature: -20 °C to 55 °C
• Storage Temperature: -20 °C to 55 °C
• Relative Humidity: 5%-95%

Features

• Communication: WLAN, Bluetooth
• Management: EcoFlow App

1 Test conditions: 0.5C/0.5C charging/discharging at 25 °C.

2 Performance may be affected at temperatures above 35 °C.

EcoFlow STREAM Pro

General Information

• Model: EF-EA-HD-P2K-800, EF-EA-HD-P2K-600
• Dimensions: 255 x 284 x 458 mm
• Net Weight: 22.8 kg
• Typology: Insulated
• IP Protection Rating: IP65
• Pollution Degree: PD3
• OVC Category: DC: II, AC: III
• Environmental Category: Indoor/Outdoor
• Cooling Method: Natural Convection (no fan)

Battery Information

• Rated Power: 1.92 kWh
• Rated Voltage: 19.2 V-
• Lifecycle: 6,000
• Cell Chemistry: LFP (LiFePO4)

PV Terminal (DC)

• Number of MPPTs: 3
• MPPT Voltage Range: 15-60 V-
• Max. Input Power: 1,500 W (500 W per MPPT)
• Max. Input Voltage: 60 V
• Max. Input Current: 14 A
• Max. Input Short Circuit Current: 20 A

Grid Terminal (AC)

• Rated Voltage and Frequency: 230 V~, 50 Hz
• Rated Output Power: EF-EA-HD-P2K-800: 800 W, EF-EA-HD-P2K-600: 600 W
• Rated Output Current: EF-EA-HD-P2K-800: 3.48 A, EF-EA-HD-P2K-600: 2.61 A
• Max. Input Current: 10 A
• Max. Input Power: 2,300 W
• Power Factor: 1 (-0.8 to +0.8)

AC Outlet (AC)

• Rated Voltage and Frequency: 230 V~, 50 Hz
• Max. Output Power: 1,200 W
• Max. Output Apparent Power: 1,200 VA
• Rated Output Current: 5.22 A
• Max. Output Current (Bypass Mode): 10 A
• Max. Input Power: EF-EA-HD-P2K-800: 800 W, EF-EA-HD-P2K-600: 600 W
• Max. Input Apparent Power: EF-EA-HD-P2K-800: 800 VA, EF-EA-HD-P2K-600: 600 VA
• Max. Input Current: EF-EA-HD-P2K-800: 3.48 A, EF-EA-HD-P2K-600: 2.61 A
• Power Factor: 1 (-0.8 to +0.8)

Parallel Terminal (AC)

• Rated Voltage and Frequency: 230 V~, 50 Hz
• Max. Output Power: 2,300 W
• Max. Output Apparent Power: 2,300 VA
• Max. Output Current: 10 A
• Max. Input Current: 10 A
• Max. Input Power: 2,300 W
• Max. Input Apparent Power: 2,300 VA
• Power Factor: 1 (-0.8 to +0.8)

Environment

• Operating Altitude: ≤ 4,000 m
• Operating Temperature: -20 °C to 55 °C
• Storage Temperature: -20 °C to 55 °C
• Relative Humidity: 5%-95%

Features

• Communication: WLAN, Bluetooth
• Management: EcoFlow App

1 Test conditions: 0.5C/0.5C charging/discharging at 25 °C.

2 Performance may be affected at temperatures above 35 °C.

Product Compatibility List

Solar Panel

Micro-Inverter

Smart Plug

Smart Meter