Product Overview
The OSRAM Downlight Set Slim is a range of LED downlights designed for efficient and modern lighting solutions. This document provides technical specifications and installation guidance for the DL SET SLIM 120 ADJ CUT 830 WT and DL SET SLIM 173 ADJ CUT 830 WT models.
Technical Specifications
| Model | EAN | W | lm light source | lm output | K | (°C) | V~ | mA | Hz | DF | PF | (°) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DL SET SLIM 120 ADJ CUT 830 WT | 4058075854376 | 9 | 1050 | 810 | 3000 | -20...+40 | 220-240 | 45 | 50/60 | >0.7 | >0.7 | 120 |
| DL SET SLIM 173 ADJ CUT 830 WT | 4058075854390 | 18 | 1850 | 1400 | 3000 | -20...+40 | 220-240 | 89 | 50/60 | >0.7 | >0.7 | 120 |
Note: The final column in the table likely refers to lifespan (e.g., L70/B50) or a similar metric, indicated by '50000' for both models.
Dimensions and Weights
DL SET SLIM 120 ADJ CUT 830 WT:
- Weight: 124 g
- Dimensions: Height (H) 37 mm, Diameter (Ø) 121 mm
DL SET SLIM 173 ADJ CUT 830 WT:
- Weight: 200 g
- Dimensions: Height (H) 40 mm, Diameter (Ø) 173 mm
Diagram Description: Visuals show two downlight units, one smaller and one larger, with their respective weights and EANs. Separate diagrams illustrate the height (H) and diameter (Ø) of the units, with a table confirming these dimensions for each model.
Installation Guide
Follow these steps for proper installation:
-
Step 1: Power Preparation
Ensure the power supply is switched off at the main panel. The diagram shows a switch panel with multiple ON/OFF switches, indicating the need to isolate the circuit.
-
Step 2: Ceiling Preparation
Cut an appropriate hole in the ceiling for the downlight. The required cut-out diameter is Ø55-90mm for the DL SET SLIM 120 model and Ø55-145mm for the DL SET SLIM 173 model.
-
Step 3: Connect LED Driver
Connect the LED driver to the downlight unit. The diagram shows the driver's output wires connecting to the downlight's input.
-
Step 4: Wire to Mains
Connect the LED driver to the AC mains supply (220-240V). Ensure correct connections for Live (L) and Neutral (N). The diagram indicates recommended wire lengths and clearances: 14mm, 7mm, 5-15mm, ≥25mm, and >50mm.
-
Step 5: Install Downlight
Insert the connected downlight unit into the prepared ceiling opening.
-
Step 6: Power On
Switch the power back on at the main panel. The diagram shows a hand operating the ON switch.
-
Step 7: Operation
The downlight is now installed and ready for use. The final diagram shows the illuminated downlight in the ceiling.
Important Notes
[alert] Check the wall/ceiling for suitability before installation. If you are uncertain, seek professional advice.
Energy Efficiency
This product contains a light source of energy efficiency class E.
Manufacturer and Contact Information
Manufactured by: LEDVANCE SASU, 5 rue d'Altorf, 67120 Molsheim France. Visit www.ledvance.com for more information.
Also distributed by: LEDVANCE Ltd, Sterling House, 810 Mandarin Court, Warrington, Cheshire, WA1 1GG, United Kingdom.
Recycling and Disposal
[recycle-symbol] This product and its accessories are recyclable. Please dispose of them at designated collection points for electrical waste or return them to stores according to local regulations.
