LG ARUN060GSS4 Multi V™ S Heat Pump - 5.0 Ton Outdoor Unit

Product Overview

This document provides detailed specifications for the LG ARUN060GSS4, a 5.0 Ton Outdoor Unit for the Multi V™ S Heat Pump system. It includes performance data, electrical requirements, unit dimensions, and AHRI certified ratings.

Performance Specifications

Cooling Mode

• Rated Capacity: 60,000 Btu/h
• Power Input: 6 kW

Heating Mode

• Rated Capacity: 64,000 Btu/h
• Power Input: 5.3 kW

Rated capacity is based on the following conditions: Cooling - Indoor: 80°F DB / 67°F WB, Outdoor: 95°F DB; Heating - Indoor: 70°F DB, Outdoor: 47°F DB / 43°F WB.

Electrical Specifications

• Power Supply: 208-230V / 60Hz / 1Ø
• MOP (A): 40
• MCA (A): 25.4
• Rated Amps (A): 19.5
• Compressor (A): 19.5
• Fan (A) x Qty: 0.5 x 2

Piping Specifications

• Refrigerant Charge (lbs): 7.7
• Liquid Line (in, OD): Ø3/8 Braze
• Vapor Line (in, OD): Ø3/4 Braze

Compressor and Fan Details

Compressor

• Type: Hermetically Sealed Scroll
• Quantity: 1
• Oil / Type: PVE/FVC68D

Fan

• Type: Axial Flow Fan
• Quantity: 2
• Motor / Drive: Brushless Digitally Controlled/Direct
• Air Flow Rate (CFM): 3,885

Standard Features and Optional Accessories

Standard Features

• Night Quiet Operation
• Fault Detection and Diagnosis

Optional Accessories

• Low Ambient Baffle Kit - ZLABGP04A (2 required)
• Drain Pan Heater - PQSH1200

*Installation of an optional Low Ambient Wind Baffle Kit will allow operation down to -9.9°F in cooling mode.

Unit Data and Operating Range

• Operating Range - Cooling: 23-122°F DB
• Operating Range - Heating: -13 to +61°F WB
• Refrigerant Type: R410A
• Refrigerant Control: EEV
• Max Number of Indoor Units: 12
• Sound Pressure: 57 dB(A)
• Net Unit Weight: 260 lbs
• Shipping Weight: 291 lbs
• Communication Cable: 2 x 18 AWG (No. x AWG)
• Heat Exchanger Coating: GoldFin™

Dimensional Information

The unit dimensions are provided in inches. Key dimensions include:

• Overall Width: 37-13/32 inches
• Overall Height: 54-11/32 inches
• Overall Depth: 21-15/32 inches
• Bolt Diameter: 1/2" (typical of 4)

Clearance requirements:

• Minimum Airflow Clearance: 4 inches (front and sides)
• Minimum Maintenance Clearance: 24 inches (front), 12 inches (sides)
• Compressor and Control Component Access: Located on the side.
• Base pan drain holes are present.

Note: Arrows in diagrams indicate the direction of airflow.

AHRI Certified Data

Notes:

• For AHRI rating, refer to the AHRI website http://www.ahridirectory.org.
• The combination ratio must be between 50% - 130%.
• Sound Pressure levels are tested in an anechoic chamber under ISO Standard 3745.
• Communication cable between ODU, IDU(s), and Central Controller must be a minimum of 2-conductor, 18 AWG, twisted, stranded, and shielded. Ensure the communication cable shield is properly grounded to the ODU chassis only. Do not ground the communication cable at any other point. Wiring must comply with all applicable local and national codes.
• Nominal data is rated 0 ft above sea level, with 25 ft of refrigerant line per indoor unit and a 0 ft level difference between outdoor and indoor units. All capacities are net with a combination ratio between 95-105%.
• Power wiring cable size must comply with the applicable local and national codes.
• The voltage tolerance is ± 10%.

Manufacturer Information

LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. "LG Life's Good" is a registered trademark of LG Corp. Visit https://www.lghvac.com for more information.

For continual product development, LG reserves the right to change specifications without notice.