KingSlim D1 Pro Dash Cam Quick Start Guide

CONTENTS

• What's in the Box
• Camera Overview
• Installation
• Formatting the microSD Card
• Download the App and GPS Player
• Use the "Roadcam" App
• User Manual
• Contact Us

WHAT'S IN THE BOX

• D1 Pro Dash Cam * 1
• Car Charger with External GPS * 1
• Bracket * 1
• USB Cable * 1
• 32GB MicroSD Card * 1
• GPS Electrostatic Stickers * 2
• Car Crowbar * 1
• Cable Clips * 5
• Quick Start Guide * 1

Note: The USB cable is only used to connect the computer and the dash camera to read the card.

CAMERA OVERVIEW

1 USB Power Port

2 Bracket Slot

3 Front Camera

4 Power Button

5 Microphone

6 MicroSD Card Slot

7 IR LEDs & Indicator light

8 Screen

9 Inside Camera

10 Speaker

11 Reset

12 Set Buttons

13 Wifi Button

Note: Short pressing the power button also can switch images of the front or inside showed alone or front and inside displayed simultaneously on-screen.

INSTALLATION

1. Insert the microSD Card.
2. Take the film off from the suction cup.
3. Using the crowbar to take off the nameplate on the slot, then insert the bracket into the slot of the camera.
4. Firstly clean the windshield with a dry cloth, secondly put and press the suction cup on the windshield to make sure there is no air inside the suction cup, last rotate to fix the bracket. (when install, please don't let the rearview mirror block the camera's infrared light.)
5. Adjust the viewing angle of the dash cam to get a good view.
6. Connect the car charger to the car cigarette lighter, then insert the USB end of the charger into the USB power port of the dash camera, please refer to the below picture.
7. Attach the electrostatic sticker of GPS to the top edge of the windshield, and then fix the GPS module on the electrostatic sticker, please refer to the below picture.
8. Fix the cable with a cable clip at the place where the icon is (please refer to the below picture), then use the yellow crowbar to hide the cable.

Notes:

• After powering on the dash cam through the car charger, the dash cam will automatically turn on and start recording (if the card has been inserted). To change settings, please firstly stop recording.
• Please charge for 30 minutes before using this dash cam powered by the built-in battery.
• The built-in battery is only used to power the "parking monitor" function. In normal use, please plug the car charger into the cigarette lighter of the car to power the dash cam. The built-in battery is not recommended as a normal power supply for the dash cam. This is to avoid parking monitoring failure caused by running out of battery while the car is parked.
• The camera can also be powered by connecting it to a power source such as your DC 5V phone adapter via the USB cable. When charging, please shut down the camera by long pressing the power button.
• Regarding the usage of the cable clip, only one clip is needed to fix the outlet position of the USB cable which connects to the dash camera's power port, the remaining cable must be hidden along the top edge of the windshield. Please hide the cable according to the above picture.

FORMATTING THE MICROSD CARD

The microSD Card is needed to format firstly on the computer and then format on the camera to make sure it can be more compatible with the camera. When using the 32GB card above, the card has to be formatted on the camera, then the camera can record normally. If not format, the camera will show "Insert SD card" on the screen. This dash cam supports a microSD card, up to 128G with class 10 & above.

1. Please format the card on the computer firstly.
2. After inserting the card into the camera and turning on the camera, press [stop recording] button to stop recording.
3. Press [settings] to enter setting interface, press [menu] and press [OK] to enter Setup interface. Press [menu] to choose “Format", press [OK] to format interface and press [OK] and choose “OK”, then press [OK] to format the card. After finishing the format, it will back to the setup interface.

Note:

• All data will be deleted. Before formatting your memory card, please remember to backup your important data on your other devices.
• Every time you insert an microSD card, please format it in the camera to ensure that the microSD card is compatible with the camera.

DOWNLOAD THE APP AND GPS PLAYER

Download the "RoadCam" app on the App Store or Google Play.

Download on the App Store

GET IT ON Google Play

Download the GPS player: www.kingslim.net/player

Note: Please turn off the anti-virus software on the computer before installing the player or click "allow" when prompted.

USE THE "ROADCAM” APP

CONNECT WITH THE APP

1. Long press the Wifi button on the bottom of camera to enter the Wifi settings interface.
2. Go to your smartphone's Wifi settings and connect to the Wifi name that's shown on the dash cam. Enter the password and confirm the Wifi network.
3. Open the "RoadCam" app, tap "Add Recorder", wait a few seconds to enter the preview interface.
4. Tap the video or photo icon to control the dash cam, either recording videos or shooting photos.

Note: WiFi is on, please connect.

SSID: DVR74ee2aad313d

PWD: 12345678

DOWNLOAD OR DELETE VIDEOS AND PHOTOS

1. Tap the [record] icon to stop the recording.
2. Tap the [movie] or [photo] icon to check the videos or photos.
3. Tap "Select" and choose videos or photos that you want.
4. Tap the download or delete icon to download or delete.

Note: To exit the Wifi feature, please press the power button on the dash cam.

USER MANUAL

Scan the following QR code or visit the KingSlim website to download detailed user manual.

www.kingslim.net/manual/d1pro.pdf

CONTACT US

For any inquiries with KingSlim products, please feel free to contact us, we will respond within 24 hours.

E-mail: cs@kingslim.net

Tel: 888-811-1140 (US) Mon-Fri (except holiday) 9am-5pm (EST)

Official website: www.kingslim.net

The microSD, microSDHC, microSDXC and SD marks and logos are trademarks of SD-3D, LLC.

App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Google Play and the Google Play logo are trademarks of Google LLC.