SONOFF SNZB-06P Zigbee Human Presence Sensor

Introduction

The SONOFF SNZB-06P is a human-presence sensor utilizing 5.8GHz microwave technology. It actively detects ambient motion and human breath to realize its presence sensing function. This sensor helps prevent the inconvenience of lights turning off automatically when someone is present, enhancing smart home automation.

Note: Functional characteristics depend on the Zigbee gateway. The equipment is suitable for mounting at heights of 2 meters or less.

Key Features

• ? Microwave Radar
• ? Presence Detection
• ☀️ Light Sensing
• ? Intelligent Linkage

Device Overview

The device consists of the following parts:

• ① Human presence sensor
• ② Magnetic base
• ③ Button
• ④ LED indicator (Red)
• ⑤ Power input interface (Type-C)

LED Indicator Status

Specifications

App Setup and Device Pairing

Download the "eWeLink" App from Google Play Store or Apple App Store to add your SONOFF Zigbee gateway.

Adding the Device via QR Code:

1. Power on the device: Connect the device to a power source using the Type-C interface.
2. Enter "scan QR code" mode: Open the eWeLink app, navigate to the device adding section, and select the "Scan QR code" option.
3. Scan the QR code on the device: Point your phone's camera at the QR code located on the device.
4. Select "Add Device": Confirm the device detection in the app and select "Add Device".
5. Long press the button for 5 seconds: Press and hold the button on the device for 5 seconds. The LED indicator will start flashing slowly for 180 seconds, indicating it's in pairing mode.
6. Select Zigbee gateway: Choose your Zigbee gateway from the list in the eWeLink app.
7. Wait for addition: The app will search for and add the device. Wait until the addition is complete. The LED indicator flashing twice signifies that the device is within the effective communication distance of the gateway.

Matched Gateways:

• SONOFF Gateways: ZBBridge, ZBBridge-P, NSPanel PRO, AIBridge, ZBDongel-P, ZBDongel-E.
• Third-party compatible gateway models: Amazon Gateway Model: Echo Plus 2nd, Echo Show 2nd.
• Other gateways supporting Zigbee 3.0 wireless protocol are also compatible. Detailed information may vary by final product.

*Note: The device may display as a human motion sensor under some gateways.

Installation Methods

Install the device in the desired location. The LED indicator flashing twice confirms effective communication distance with the Zigbee network (router or hub).

1. Place on the desktop: Position the sensor on a flat surface.
2. Attached to a metal surface: Use the magnetic base to attach the sensor to a metal surface.
3. Stick to the wall: Use the included 3M adhesive tape on the base to attach the sensor to a wall.
4. Base screws fixed to the wall: Secure the base to the wall using screws for a more permanent installation.

Detection Zone

The radar's radial detection distance is approximately 4 meters.

Diagram description: A circular area is shown, labeled "4M", indicating the detection range.

Cautions

1. Keep moving objects (curtains, greenery, fans, pets) clear during installation to avoid misjudging presence.
2. Non-metallic materials like glass, plastic, and ceramics can be pierced through by the sensor's detection.
3. When installing multiple sensors, ensure they are oriented in the same direction or back-to-back, avoiding front-to-front irradiation. Maintain a distance of at least 1.5 meters between sensors.

Regulatory Compliance

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment causes harmful interference to radio or television reception, try correcting it by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment to an outlet on a circuit different from the receiver.
• Consulting a dealer or experienced radio/TV technician.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits for an uncontrolled environment. It should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating with any other antenna or transmitter.

ISED Notice (Canada)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003(B) and RSS-247 of Industry Canada.

ISED Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits for an uncontrolled environment. It should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating with any other antenna or transmitter.

SAR Warning (Canada): Under normal use, keep a separation distance of at least 20 cm between the antenna and the user's body.

WEEE Disposal and Recycling Information

Products bearing the WEEE symbol (♻️) are waste electrical and electronic equipment and should not be mixed with unsorted household waste. Hand over your waste equipment to a designated collection point for recycling to protect human health and the environment. Contact local authorities for more information.

EU Declaration of Conformity

Shenzhen Sonoff Technologies Co., Ltd declares that the radio equipment type SNZB-06P complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: https://sonoff.tech/compliance/

For CE Frequency:

• Zigbee: 2405-2480MHz
• FMCW: 5725-5875MHz
• RF Output Power: Zigbee: ≤10dBm, FMCW: ≤10dBm

Disposal Information (Italian context):

Check local municipal regulations for proper disposal. Separate components and dispose of them correctly.

Manufacturer Information

Manufacturer: Shenzhen Sonoff Technologies Co., Ltd.

Address: 3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China

ZIP code: 518000

Website: sonoff.tech

Service email: support@itead.cc

Made in: China

Logos: CE, FC, Recycling symbol (♻️), 10.