SONOFF SNZB-06P Zigbee Human Presence Sensor

User Manual V1.0

Introduction

The SNZB-06P is a human-presence sensor utilizing 5.8G microwave technology. It detects ambient motion and human breath to provide presence sensing. This feature helps avoid scenarios where lights might automatically turn off when someone is present, enhancing home automation and convenience.

• Microwave radar detection
• Presence detection
• Light sensing capabilities
• Intelligent linkage with other smart devices

*Functional characteristics depend on the Zigbee gateway's capabilities.

*The equipment is designed for mounting at heights up to 2 meters.

Device Components

The SNZB-06P sensor consists of the following parts:

Instruction of LED indicator status

Specification

Download the eWeLink App & Add SONOFF Zigbee Gateway

To use the SNZB-06P, you need to download the "eWeLink" App. It is available from the Google Play Store or Apple App Store.

Adding the Device via QR Code

Follow these steps to add your SNZB-06P device:

1. Power on the device: Connect the sensor to a power source using the Type-C cable.
2. Enter "scan QR code" mode: On your smartphone, open the eWeLink app, navigate to the device list, and tap 'Add Device', then select 'Scan'.
3. Scan the QR code on the device: Point your smartphone's camera at the QR code located on the SNZB-06P sensor.
4. Select "Add Device": Once the QR code is recognized, tap 'Add Device' on your smartphone screen to complete the process.

Adding the Device via Button Pairing

Alternatively, you can pair the device using the button:

5. Long press the button for 5 seconds: Press and hold the button on the SNZB-06P until the LED indicator starts flashing slowly.
6. The LED indicator flashes slowly for 180s: This indicates the device is in pairing mode.
7. Select Zigbee gateway: In the eWeLink app, select your Zigbee gateway from the list and proceed to the next step.
8. Wait until the addition is done: The app will search for and add the device. A confirmation message will appear once the addition is complete.

Matched Gateways

The SNZB-06P is compatible with the following gateways:

• SONOFF Gateways: ZBBridge, ZBBridge-P, NSPanel PRO, AIBridge, ZBDongel-P, ZBDongel-E.
• Third-party compatible gateway models: Amazon Gateway Models like Echo Plus 2nd, Echo Show 2nd.
• Other gateways supporting the ZigBee 3.0 wireless protocol are also compatible. Detailed information may vary based on the final product.

*Note: The device may display as a human motion sensor on certain gateways.

Effective Communication Distance Verification

When the device is installed in the desired location, press the pairing button. If the LED indicator flashes twice, it signifies that the device and the Zigbee network (router or hub) are within effective communication distance.

Installation

Choose the most suitable installation method for your environment:

1. Place on the desktop: Position the sensor on a flat surface.
2. Attached to the metal surface with the magnetic base: Utilize the magnetic base to attach the sensor to any metallic surface.
3. Stick to the wall with 3M adhesive of the base: Apply the included 3M adhesive tape to the base and affix it to a wall.
4. Base screws fixed to the wall: For a more secure mounting, use the provided screws to fix the base to the wall.

Detection Zone

The radar's radial detection distance is approximately 4 meters.

[Diagram showing a semi-circular detection area extending approximately 4 meters from the sensor.]

Cautions

1. Keep moving objects such as curtains, greenery, fans, and pets away from the sensor during installation to prevent misjudgments of nearby presence.
2. Non-metallic materials like glass, plastic, ceramics, and plank can be pierced through by the sensor's detection signal.
3. When installing multiple sensors, orient them in the same direction or back-to-back to avoid front-to-front irradiation. Ensure each sensor is placed more than 1.5 meters away from others.

FCC Warning

FCC compliance statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISED Notice (Canada)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003(B). This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.

[French translation of ISED compliance and exposure statements follows, detailing similar conditions for interference and exposure limits.]

ISED Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

[French: Cet équipement est conforme aux limites d'exposition aux rayonnements de la ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et fonctionner à au moins 20cm de distance d'un radiateur ou de votre corps. Cet émetteur ne doit pas être co-localisé ou fonctionner en conjonction avec une autre antenne ou un autre émetteur.]

SAR Warning

Under normal use conditions, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

[French: Dans des conditions normales d'utilisation, cet équipement doit être maintenu à une distance d'au moins 20 cm entre l'antenne et le corps de l'utilisateur.]

WEEE Warning

WEEE Disposal and Recycling Information

All products bearing the WEEE symbol are considered waste electrical and electronic equipment (WEEE) as per directive 2012/19/EU. They should not be mixed with unsorted household waste. To protect human health and the environment, please hand over your waste equipment to a designated collection point for recycling. Correct disposal and recycling help prevent potential negative consequences. Contact local authorities for information on collection points and terms.

EU Declaration of Conformity

Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type SNZB-06P complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: https://sonoff.tech/compliance/

For CE frequency

• Zigbee: 2405-2480MHz
• FMCW: 5725-5875MHz
• RF Output Power: Zigbee: ≤10dBm, FMCW: ≤10dBm

Recycling Information (Italian)

[Italian text: Verifica le disposizioni del tuo Comune. Separa le componenti e conferiscile in modo corretto.]

RACCOLTA DIFFERENZIATA

Manufacturer Information

Manufacturer: Shenzhen Sonoff Technologies Co., Ltd.

Address: 3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China

ZIP code: 518000

Service email: support@itead.cc

Website: sonoff.tech

Made in China

[Compliance logos: CE, FC, WEEE symbol (recycle symbol with crossed-out bin), other regulatory marks.]