Belling Farmhouse 90PYR Cooker Hood Installation Guide
This document provides essential information for the correct and safe installation of your Belling Farmhouse 90PYR Cooker Hood.
Introduction
⚠️ Warning! Before proceeding with installation, please carefully read the safety information provided in the accompanying User Manual.
Included Components and Hardware
Verify that all parts are present before beginning installation:
- Hood Body (A)
- Upper Chimney Section (B)
- Lower Chimney Section (C)
- Circular Filters (W)
- Ducting Adapter
- Screws (I): 8 pieces
- Screws (L): 8 pieces
- Screws (N): 4 pieces
Safety Precautions and Installation Requirements
Safety Guidelines:
- Installation requires the assistance of two people ?.
- Always wear protective gloves ? during the installation process.
Ducting Options:
- Flexible ducting Ø 120 mm (requires 2x clamps)
- Flexible ducting Ø 150 mm (requires 2x clamps)
Mounting Specifications:
- Maintain a minimum clearance of 65 cm above the hob.
- Ensure the mounting surface is level and at a 90° angle.
Installation Procedure
Follow these steps carefully for proper installation:
Step 1: Planning and Marking
Determine the ducting path (vertical or horizontal). For vertical installations, ensure a slight upward slope (approx. 2°). Mark the precise mounting locations on the wall above the cooking hob.
Step 2: Review Dimensions
Familiarize yourself with the hood's dimensions: Width (898-998 mm), Depth (490 mm), Adjustable Height (MIN 530 mm - MAX 870 mm), Chimney (180 mm x 210 mm).
Step 3: Install Wall Bracket
Attach the wall mounting bracket securely. Refer to the diagram for specific measurements (e.g., 60.60, 125, 220, 32, 205). Drill Ø 8 mm holes (X8) as indicated for mounting.
Step 4: Attach Hood to Bracket
Lift and position the cooker hood onto the wall bracket. Secure it using 8 screws (I).
Step 5: Final Hood Securing
Further reinforce the hood's attachment to the wall using 8 screws (L).
Step 6: Connect Upper Chimney
Slide the upper chimney section (B) over the hood body.
Step 7: Secure Chimney Section
Fasten the upper chimney section (B) in place.
Step 8: Wall Mounting Check
Confirm the hood is firmly and safely mounted to the wall.
Step 9: Select Duct Outlet Size
Choose the appropriate duct outlet size for your ventilation system: Ø 150 mm or Ø 120 mm.
Step 10: Connect Flexible Ducting
Attach the flexible ducting to the hood's outlet. Secure the ducting using 4 screws (L).
Step 11: Install Check Valve
Insert the check valve into the ducting system to prevent backflow.
Step 12: Re-check Wall Mounting
Ensure all wall-mounting connections are secure.
Step 13: Install Motor/Fan Unit
Carefully insert the motor/fan unit (W) into its housing within the hood.
Step 14: Join Chimney Sections
Connect the upper and lower chimney sections. Secure them together using 4 screws (L).
Step 15: Complete Chimney Assembly
Ensure the chimney sections are correctly aligned and assembled.
Step 16: Secure Upper Chimney (B)
Fasten the upper chimney section (B) to the lower section or wall mount using 4 screws (N).
Step 17: Attach Chimney B to C
Connect chimney section B to chimney section C, ensuring a snug fit.
Step 18: Final Chimney Configuration
The chimney structure is now fully assembled and in place.
Step 19: Install Grease Filters
Insert the grease filters (Z) into their designated slots within the hood body.
Step 20: Install Motor/Fan and Filters
Ensure the motor/fan unit (W) is correctly installed and that all filters are properly seated.
