Soundstream VR-75XB Owner's Manual

WARNING!

For safety, certain functions are disabled unless the parking brake is engaged. Improper connection or use of the parking brake switch connection may violate applicable law and result in serious injury or damage. This unit is not intended for use with a video screen visible to the driver. To avoid accidents and legal violations, the front video image feature should never be used while the vehicle is in motion. Other video displays should not distract the driver. Viewing images on a display inside a vehicle may be illegal in some regions; obey all applicable regulations. Always wear your seat belt. The supplier disclaims all liability for failure to follow these warnings.

OPERATION PRECAUTIONS

• Connect only to a 12VDC battery with negative grounding.
• Avoid direct sunlight, high dust, high temperatures (over 40°C), or high humidity (over 90%). Cool the car interior if temperatures are high.
• Operate in well-ventilated areas.
• Do not turn the unit on/off at short intervals. Wait at least 10 seconds before turning it back on.
• Do not operate with scratched, bent, or broken discs, or force improperly loaded discs.
• Do not watch video playback while driving due to safety risks and potential legal violations (except for rear view camera and navigation systems).
• Do not install the unit where it obstructs safe driving.
• Do not disassemble the unit yourself; seek professional repair.
• Do not open or close the monitor manually to avoid damaging the tilt system.
• Do not touch the LCD screen with hard objects to prevent scratches.
• If the monitor back touches the dashboard or air-conditioner inlet after opening, adjust the TILT level in the monitor menu.
• High temperatures from parking in direct sunlight may affect operation; allow the unit to cool down.
• Use only the specified fuse type for the power cable; improper fuses can cause damage.
• Do not use irregular shaped discs.
• IR remote control operation may be hindered by the monitor; use it at a similar level to the receiver.
• Do not install the unit where the cooling fan is blocked.

Accessories

The package contains the following accessories for installation and operation:

Included items also include: Remote Control, User Manual, Warranty card, Power cable, RCA cable, Plastic outer trim ring. (Product image may vary.)

Installation / Un-installation

Note: Ensure proper wiring before installation. Use only provided parts to prevent malfunction. Install the unit where it does not obstruct the driver or passengers.

Installation

1. Insert the unit into the dashboard hole and fix it.
2. If necessary, attach the mount strap at the rear of the unit with a washer (as shown in Figure 2).
3. Push the unit into the Half Sleeve until it clicks.
4. Place the Trim Ring over the unit (if required for the vehicle). Installation is complete (as shown in Figure 3).

Removing the Unit

Insert the supplied release key into the unit and pull the unit out while keeping the release key in place (as shown in Figure 4).

Wiring Connections

Ensure a good chassis ground for optimal electrical performance. The ground connection area should be clean, bare metal.

Caution: Do not interchange wiring connections. Some car models may require modification of the power cord. Consult an authorized car dealer.

Using the ISO Connector

1. If your car has an ISO connector, connect them as illustrated.
2. For cars without ISO connectors, carefully check vehicle wiring before connecting to avoid damage.
3. Cut the connector and connect colored leads of the power cord to the car battery as per the color code table for speaker and power cables.

Note: Never connect cables while the unit is connected to the battery. Disconnecting from the battery erases preset memory. The brown cable for steering wheel control allows unit control via the steering wheel. The parking wire must be connected to a brake signal for video display safety. Two cables are for a Hands-Free device (not included).

Parking Wire Connection Diagram Description: Shows the parking brake wire from the car DVD player connecting to the parking brake switch (activated by parking brake), which indicates the parking brake light. This connects to the car battery and to the metal body part or chassis ground.

Connecting the Reversing Line to Taillight

After connecting the reversing line to the taillight, the unit will display the rear view camera image when the reverse gear is engaged.

Speaker Connection Notes:

• Use only groundless loudspeakers.
• Loudspeakers should be a minimum of 40 Watts; lower wattage may cause damage at high volumes.
• Use 4-8 Ω (Ohm impedance) loudspeakers only; higher or lower impedance may damage the unit.
• Do not use 3-cable loudspeakers or connect speaker minus to the car body (GND). The unit uses a BTL circuit, requiring insulated cables.
• Loudspeaker cables and external power amplifiers should be kept approximately 30cm away from the antenna.
• For 7" TFT display, the parking wire must be connected to ground.

Diagram Descriptions: Illustrates Correct Speaker Connection and Incorrect Speaker Connection methods.

Front Panel

The front panel features the following components:

1. TFT display: The main screen.
2. Release Button: Press to detach the front panel. The unit powers off automatically. To attach, insert the right side first, then press the left side until it clicks.
3. POWER/MUTE Button: Turns the unit on. Short press mutes volume; long press turns the unit off.
4. AMS Button: In Radio mode, starts automatic search; press and hold for manual search. Press again to tune frequency downward.
5. Menu Button: Returns to the home page.
6. BAND Button: Changes radio band (FM1, FM2, FM3, AM1, AM2).
7. MODE Button: Selects input mode (Radio, DISC, USB, CARD, Bluetooth, AV IN).
8. VOLUME Button: Adjusts volume using the knob.
9. >> / << Buttons: In Radio mode, search stations. In DVD/SD/USB, skip tracks or fast forward (hold for 2 seconds). In Bluetooth, accept incoming calls.
10. << / >> Buttons: In Radio mode, search stations. In DVD/SD/USB, skip tracks or rewind (hold for 2 seconds). In Bluetooth, reject calls or hang up.
11. OPEN/TILT Button: Opens and closes the TFT monitor. WARNING: Do not obstruct the monitor during opening/closing. Press and hold for 2 seconds to adjust tilt angle (ANGLE 1-4).
12. IR: Infrared receiver.
13. MIC slot: For Bluetooth hands-free calling.
14. DISC slot: For discs.
15. Info Display: LCD for operation information.
16. USB slot: For USB devices.
17. EJECT Button: Ejects the disc. Disc reinserts automatically if not removed within 10 seconds.
18. AUX Jack: Connect external video devices.
19. Anti-theft LED light.
20. RESET Button: Resets the unit to factory default settings using a thin, sharp object.
21. SD/MMC CARD slot: For multimedia files (MP3, etc.).

Remote Control

The remote control provides access to all unit functions:

• 1. POWER: Powers the unit on or off.
• 2. MODE: Selects input mode (Radio, DISC, USB, CARD, AV IN).
• 3. PLAY/PAUSE: Stops or resumes DVD playback.
• 4. Mute/Bluetooth: Mutes/unmutes volume. Long press enters Bluetooth mode.
• 5. BAND/RDM: Changes radio band or plays DVD randomly.
• 6. Cursor buttons: Navigate menus and select items.
• 7. MENU/ROOT: Shows main menu or DVD title menu (long press).
• 8. SUBTITLE: Selects subtitle language (if available).
• 9. Cursor buttons: Navigate menus.
• 10. ENTER: Confirms selection or setting.
• 11. Cursor buttons: Navigate menus.
• 12. SETUP: Enters the setup menu.
• 13. EJECT: Ejects the disc.
• 14. Cursor buttons: Navigate menus.
• 15. ANGLE/ACCEPT: Changes DVD viewing angle or accepts/makes Bluetooth calls.
• 16. INT/REJECT: Activates intro function or rejects Bluetooth calls.
• 17. P.SCN/RPT: Scans radio presets or saves stations (AS). Repeats tracks/chapters/titles in DVD/USB/SD modes.
• 18. STEREO/MONO: Selects stereo or mono sound reception.
• 19. VOL+: Increases volume.
• 20. A-B/ZOOM: Repeats a section (A-B) or zooms the image.
• 21. LOUD: Sets loudness on or off.
• 22. << / seek-: Skips to previous track (DVD) or searches radio stations automatically/manually.
• 23. SEL: Enters the Sound Setting menu.
• 24. >> / seek+: Skips to next track (DVD) or searches radio stations automatically/manually.
• 25. STOP/PBC: Stops playback or sets PBC on/off (VCD).
• 26. OSD: Enters DVD OSD menu or video setup.
• 27. VOL-: Decreases volume.
• 28. AUDIO/GOTO: Selects audio language (DVD), sound track (VCD), or searches for time/title/chapter.
• 29. Digit 0-9 buttons: Select radio band or DVD track.
• 30. OPEN/TILT: Optional monitor control.
• 31. DUAL: Optional function.

Note: The remote control is universal; some options may not be available for this model.

Remove Battery

Note: Remove the remote control battery if not used for an extended period to prevent leakage or corrosion. Do not place objects between the remote and the sensor. Avoid dropping the remote. Do not operate other equipment simultaneously. Dispose of batteries responsibly. Keep batteries away from children.

Main Menu

The Main Menu is the central hub for accessing all features. Tap icons to enter desired modes.

Radio Player

Tap the RADIO button to access the radio functions:

• FM/AM Band Selection: Touch the FM button to cycle through FM1, FM2, FM3, AM1, AM2.
• Station Tuning: Touch icons to manually tune forward or backward. Touch and hold to automatically scan stations.
• Mute: Mutes the sound.
• EQ Settings: Choose from User, Flat, Classic, Pop, Rock.
• AS/PS: Scan stations (1-6) or long-press to save stations with good reception.
• Seek Forward/Backward: Search for stations.
• TA: Toggle Traffic Announcement on/off.
• PTY: Select program type.
• S/M: Select stereo or mono sound reception.

Note: If a radio signal is not received, ST/MO function defaults to ST.

DVD Player

Tap the DVD icon from the main menu to access the DVD Player.

Touch Screen Menu Controls:

• Repeat: Cycle through Repeat Chapter, Repeat Title, or Repeat Off (DVD); or Repeat 1, Repeat DIR, Repeat ALL (VCD).
• Skip Track: Move to the next or previous track.
• Fast Forward (FF) / Rewind (REW): Press and hold to search tracks at various speeds (FRx2, x4, x8, x20).
• STOP: Stops playback.
• Next Page / Menu: Navigate through pages or access menus.
• Subtitle Language: Select available subtitle languages.
• Sound Channel: Select Stereo, MONO L, or MONO R.
• Viewing Angle: Change the viewing angle (if supported by the disc).
• PBC ON/OFF: Control Playback Control for VCD mode.

Notes: The DVD Player automatically starts playback upon inserting a DVD, memory card, or USB device. Warnings are displayed if the vehicle is moving for safety. The player supports video, picture, and music files.

Disc/USB/SD/MMC Interface Operation

Disc

When a disc, USB, or memory card is played, the screen displays the relevant interface.

USB Device

To play MP3/MP4/WMA files, insert a USB flash drive into the USB port. The unit automatically plays MP3/MP4/WMA/JPEG files. Alternatively, press the MODE button to select USB mode.

SD/MMC Card

To play MP3/MP4/WMA/JPEG files, insert a SD/MMC card into the card slot. The unit automatically plays files or press MODE to select SD mode.

Disc Controls:

• Mute: Mutes the sound.
• File Type Selection: Choose Music, Video, or Picture files.
• Pause/Play: Controls playback.
• Skip Next/Previous Track: Navigates tracks.
• REW/FF Search: Searches tracks at various speeds.
• Enter Track Number: Input a track number to play.
• TITLE MENU: Accesses the title menu for music, picture, or video.
• EQ Settings: Adjust Bass, Middle, Treble, and choose EQ presets (User, Classic, Flat, Pop, Rock).
• INTRO: Activates the intro function.
• Random Playback: Turns random playback on or off.
• Repeat: Selects repeat modes (REP 1, REP DIR, REP ALL).
• A-B Segment Repeat: Repeats a specific segment of the track.

Setting Control

Access the SETTING menu via the SETUP icon on the main menu to customize system settings.

Sound Settings:

• EQ: User, Flat, Classic, Pop, Rock.
• BALANCE/FADER: Adjust audio balance and fader.
• BEEP: Enable/disable keypad sound.
• LOUD: Turn loudness on or off.
• LOUD LEVEL: Adjust the overall loud level.
• SUBWOOFER: Turn subwoofer on or off.
• SUBWOOFER LPF: Select Low Pass Filter frequency (80Hz, 120Hz, 160Hz).
• SUBWOOFER LEVEL: Adjust subwoofer volume.

Display Settings:

• BACK LIGHT: Adjust screen brightness (LOW, MID, HIGH).
• LCD COLOR: Select color scheme (AUTO, Red, Yellow, Green, Cambridge Blue, Purple, White).
• BACKLIGHT TIME: Set auto-off timer for backlight (OFF, AFTER 10S, AFTER 20S, AFTER 30S).

Radio Settings:

• RADIO AREA: Select region (Europe, USA, South America, Russia).
• STEREO: Turn stereo reception on or off.
• TA VOLUME: Adjust Traffic Announcement volume.
• TA: Select Traffic Announcement on or off.

General Settings:

• AUTO CONNECT: Turn auto-connect on or off.
• Parental Lock: Lock/unlock channels with mature content using password (default "0000").
• TILT MODE: Select Auto or Manual tilt.
• TILT ANGLE: Adjust monitor tilt angle (1-4).
• CLOCK DISPLAY: Show or hide the clock on screen.
• CLOCK SETTING: Set the current time.
• EEPROM RESET: Reset device to factory default settings.

DVD Settings:

• UNLOCK ALL CHANNELS: Unlock all channels.
• LOCK/UNLOCK CHANNEL SET: Lock or unlock specific channels.
• CODE CHANGE: Change the parental lock code.
• DEFAULT: Reset parental code to default "0000".
• SUBTITLE LANG: Select subtitle language (English, French, Italian, Dutch, German, Spanish, Portuguese).
• AUDIO LANG: Select audio language.
• MENU LANG: Select menu language.
• PASSWORD: Set a password.
• RATING: Set content rating (1kid safe to 8 adult).
• TV TYPE: Set aspect ratio (4:3PS, 4:3LB, 16:9).
• NTSC/PAL: Select video output standard.
• DEFAULT: Restore DVD settings.

System:

SystemInfo: Displays software version information (SERVO, MPEG, Main Unit, Bluetooth).

SiriusXM

SiriusXM Vehicle Tuner Connections

SiriusXM Satellite Radio requires the SiriusXM-Connect Vehicle Tuner (sold separately) with the SiriusXM logo for compatibility.

Connection: Line up the connector with the pins and push the cable into the head unit's connector until it clicks. Do not force if misaligned.

SiriusXM Section

Before using SiriusXM, connect the SiriusXM Connect Vehicle Tuner and antenna. Tap the SXM icon on the main menu to enter SiriusXM mode. SiriusXM offers over 140 channels, including commercial-free music, sports, news, talk, comedy, and entertainment. A SiriusXM Vehicle Tuner and Subscription are required. Visit www.siriusxm.com for more information.

Tuner Activation

A subscription is required. Activate via www.siriusxm.com (ACTIVATE RADIO) or by calling SiriusXM Listener Care at 1-866-635-2349. Activation typically takes 10-15 minutes, up to an hour.

Radio ID

The 8-character Radio ID can be found on channel 0 or on the underside of the SiriusXM Vehicle Tuner. Note: The Radio ID does not use letters I, O, S, F.

Listening to SiriusXM Satellite Radio

After installing the tuner, press the SXM icon on the main menu to enter SiriusXM mode.

SiriusXM Setup Menu

Access via SETUP icon on the main menu, then press General and enter SiriusXM setup.

Displayed Information

The screen shows "Tuner not connected" or "Connected Tuner" status.

SiriusXM Controls:

• Mute: Mute sound.
• Tune Next/Previous Channel: Navigate channels.
• Select Bands: Choose SXM1, SXM2, SXM3.
• Direct Tuning: Scan channels by inputting number.
• Tone Equalizer: Adjust tone between User, Classic, Flat, Pop, Rock.
• Display Channels by Category: Show channels in a selected category.

Note: Direct tuning is supported. Tap "CH" on the menu, then input the channel number.

SiriusXM Advisory Messages

Bluetooth Section

Warning: Driving and talking on the phone simultaneously is dangerous. Park the car before using the phone. The supplier is not liable for violations of this warning.

Enter Bluetooth mode by tapping the Bluetooth icon on the Main Menu, long-pressing the mute/Bluetooth button on the remote, or pressing the mode button.

Bluetooth Interface Icons:

• Dial: Enter call mode.
• Music: Start Bluetooth Music player.
• In calling: Check received calls.
• Out calling: Check dialed calls.
• Missed calling: Check missed calls.
• Phone Book: Access phone book functions.
• Translate to mobile mode: Switch to mobile phone mode.
• Clear number: Clear entered number.
• Hand up/Reject: End or reject calls.
• Make/Accept call: Initiate or answer calls.

Pairing Mode

For first-time use, pair your mobile phone. The BT icon and Pairing mark will blink. Once connected, the BT icon is solid, and the phone name appears. Follow your mobile device's pairing instructions: search for "SoundStream", input password "0000", and confirm. "Enter Number" will display upon successful pairing.

Auto-connect / Disconnect

The unit automatically connects to the last paired phone upon power-on. If the phone is not found within a minute, searching stops. To reconnect from standby, long-press the Bluetooth button on the remote. To disconnect, turn off Bluetooth on your phone.

Dial Button

Enter call mode. Make and receive calls via Bluetooth. Tap the phone number and the call button. Tap the button to hang up. Tap the button to delete a wrong digit, or use the Reject/INT button on the remote to delete all numbers. Tap the button to call the latest number from the call log.

Voice Transfer

During a call, tap the Transfer button to switch between Bluetooth mode and the phone. The phonebook supports Western Characters only.

(A2DP) Music Mode

Tap the Music button to play music via Bluetooth. Use the controls for previous, play/pause, stop, and next. A2DP (Advanced Audio Distribution Profile) receives audio signals from the phone, amplifies them, and plays them through the car speakers. Your mobile phone must support A2DP.

Other Functions

AUX IN Mode

Tap the AUX-IN button on the main menu to connect an external audio source.

Subwoofer

Connect the subwoofer to the unit's sub output. Tap MENU, navigate to SOUND, and set subwoofer ON.

Parking

The video image can be displayed only when the car is stopped and the parking brake is engaged.

Rear View Camera

The unit supports rear view camera output. Connect your camera to the rear view camera input and the reverse wire to the rear gear light. The rear view camera picture will be enabled when backing up.

Notes on Disc

Loudspeaker Requirements: Use only groundless loudspeakers, minimum 40W, 4-8 Ω impedance. Do not use 3-cable speakers or connect speaker minus to the car body. Ensure speaker cables and external power amplifiers are kept 30cm away from the antenna. For 7" TFT display, the parking wire must be connected to ground.

Handing Discs:

Hold discs with both hands or by the edge with one hand.

Cleaning Discs:

Fingerprints or dust can reduce quality. Gently wipe from the center outwards with a soft cloth. Do not use damaged discs, scratch the surface, attach paper/seals, use benzene, thinner, or record spray. For tough dirt, use a slightly damp soft cloth, then wipe dry.

Irregular Shaped Discs:

Discs like heart-shaped or hexagonal ones cannot be played and may damage the player.

Storing Discs:

Store discs vertically in their cases. Avoid hot, humid, direct sunlight, or extremely low temperatures.

Troubleshooting

General Issues:

• Symptom: Power does not turn on (No sound). Cause: Fuse blown, incorrect wiring. Remedy: Replace fuse with same amperage; consult retailer if it blows again. Consult local retailer for wiring issues.
• Symptom: No sound output with amplifiers/antenna. Cause: Power antenna lead shorted to ground, excessive current required. Remedy: Turn off unit, remove wires, check for shorts with an ohm meter, turn on, reconnect wires one by one. Use an external relay if needed.
• Symptom: Nothing happens when buttons are pressed, Display inaccurate. Cause: Microprocessor malfunction, dirty panel/connectors. Remedy: Turn off, press [no open] button, remove DCP, press reset button for 2 seconds. Wipe connectors with a soft cloth moistened with cleaning alcohol.
• Symptom: Sound is bad after power is turned on. Cause: Dirty, scratched, or warped compact disc; water droplets on internal lens. Remedy: Clean disc without scratches, replace disc, or let unit dry for about 1 hour with power on.
• Symptom: Small LCD display error message (ERROR 1, 2, 3). Cause: Deck mechanism error (ERROR 1), disc/servo error (ERROR 2), USB error (ERROR 3). Remedy: Reset the unit. Change the disc or reset. Remove and reinsert USB, check file, or reset.

Specific Issues:

• Symptom: NO POWER. Cause: Car ignition not on, fuse blown. Remedy: Turn ignition key to "ACC". Replace fuse.
• Symptom: DISC CANNOT BE LOADED. Cause: Disc present, inserted upside down. Remedy: Remove disc, insert new one with label facing upward.
• Symptom: DISC CANNOT BE READ. Cause: Disc extremely dirty or defective, high internal car temperature. Remedy: Clean or try a new disc. Cool the car until ambient temperature returns to normal.
• Symptom: NO SOUND. Cause: Volume minimum, wiring not properly connected. Remedy: Adjust volume. Check wiring connection.
• Symptom: OPERATION KEYS DO NOT WORK. Cause: Microcomputer not operating properly due to noise, front panel not fixed properly. Remedy: Press the POWER button for about 10 seconds to reset the unit. Ensure the front panel is properly fixed.
• Symptom: SOUND SKIPS. Cause: Installation angle more than 30 degrees, disc extremely dirty or defective. Remedy: Adjust installation angle to less than 30 degrees. Clean or try a new disc.
• Symptom: RADIO DOES NOT WORK, AUTOMATIC SELECTION DOES NOT WORK. Cause: Antenna cable not connected, signals too weak. Remedy: Insert antenna cable firmly. Select a station manually.

Technical Specifications

Specifications are subject to change without notice. Mass and dimension are approximate.