Beko Sliding Refrigerator and Freezer Installation Guide
This document provides installation instructions for Beko sliding refrigerators and freezers.
Languages Included
This manual is available in the following languages:
- EN: Installation instructions
- FR: Instructions d'installation
- DE: Hinweise zur Installation
- IT: Istruzioni di installazione
- RO: Instrucțiuni de instalare
- TR: Montaj Talimatları
- PL: Instrukcje Instalacji
Product Information
Models Covered: F54220 / L54315 / S54210 (Sliding, 215)
Product Codes: 4578349305 AC
Tools and Parts Required
Tools
- ? Tape measure
- ड्रिल Drill with 2mm drill bit (Ø2)
- ✏️ Pencil
- ? T25 screwdriver
- ? PH2 screwdriver
- ✂️ Scissors
- ? Spirit level
Parts
- ? Screws (x 10) - Part a
- ? Clips (x 4) - Part b
- ⚪ Washers (x 2) - Part c
- ? Brackets (x 2) - Part d
- ? Covers (x 2) - Part e
- ?️ Rails (x 2) - Part f
- ? Hinges (x 3) - Part g
- ? Hinges (x 3) - Part h
- ? Hinges (x 3) - Part i
Note on Model Lengths:
- ** = F54220 / L54315: 1 x 1780 mm
- *** = S54210 / L54215: 1 x 1225 mm
Installation Space Requirements
Appliance Dimensions and Clearances
The installation requires specific clearances for proper operation and ventilation.
Appliance Heights:
- F54220 / L54315: Approximately 1775 mm (for ** models)
- S54210 / L54215: Approximately 1215 mm (for *** models)
Overall Appliance Height Ranges:
- ** models (F54220 / L54315): 1778 - 1788 mm
- *** models (S54210 / L54215): 1218 - 1228 mm
Cabinet Dimensions:
- Width: 540 mm / 545 mm
- Depth: Minimum 555 mm / Minimum 560 mm
Required Clearances:
- Top Clearance: 32 mm
- Base Clearance: 40 mm
- Side Clearance (for hinges): 8 mm
- Electrical Connection Clearance: Maximum 17 mm
Ventilation
Ensure adequate airflow for efficient operation:
- Minimum ventilation area: 200 cm² required at the top, bottom, and sides of the appliance.
Installation Precautions
- ⚠️ Warning: Risk of damage from liquids.
- ? Prohibited: Do not force installation or move the appliance incorrectly.
- ? Instruction: Refer to the manual/instructions.
- ? Recommendation: Wear protective gloves.
- ?? Requirement: Requires two people for safe handling and installation.
- ❌ Caution: Do not install on uneven or unsuitable surfaces.
- ❌ Caution: Ensure adequate clearance around the appliance.
- ? Requirement: Ensure the appliance is installed at a 90° angle to the wall.
Assembly Instructions
Follow these steps carefully for correct assembly.
Step 1: Attach Mounting Bracket
Attach a mounting bracket to the appliance door using part 'a' (6 screws). Ensure it clicks into place.
Step 2: Attach Component to Frame
Attach a component to the appliance frame, noting the 42 mm measurements. Use part 'a' (2 screws). Ensure it clicks into place.
Step 3: Attach Hinges
Attach the hinges to the appliance. This involves steps IV, V, and VI, ensuring parts click into place. Part 'a' (6 screws) is used for this step. Note: For Left Hand configuration, refer to '* = LH'.
