Dreo Tower Fan

Thank you for choosing Dreo!

We hope you enjoy your new Dreo Tower Fan.

Extend your warranty for free by registering your product at dreo.com/warranty.

Contents

1. Important Safety Instructions
2. Assembling Your Tower Fan
3. Knowing Your Tower Fan
4. Using Your Tower Fan
5. Cleaning and Maintenance
6. Troubleshooting
7. Dreo Customer Care

1. Important Safety Instructions

General Safety

• Children shall not play with the appliance. Cleaning and maintenance shall not be performed by children without supervision.
• Use the appliance as described in the user manual only. Any other use not recommended may cause fire, electrical shock, or personal injury.
• This appliance can be used by children aged above 8 years and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use in a safe way and understand the hazards involved.

Operation Safety

• Place the appliance on a flat, dry surface before use.
• Do not immerse in water or any other liquids.
• Do not use the appliance until the base is installed.
• Do not insert fingers, pencils, or any other objects into the grilles while in operation.
• Do not dismantle, repair, or modify. All servicing should be performed by qualified personnel.

Electricity Safety

• Ensure your electricity supply voltage matches the appliance's rating.
• Always unplug before cleaning or leaving the appliance unused. Keep hands dry when plugging/unplugging.
• Do not operate any fan with a damaged cord or plug. Discard or return to an authorized service facility.
• Do not run the cord under carpeting or cover it with rugs. Arrange the cord away from traffic areas to prevent tripping.
• WARNING: To reduce the risk of fire or electric shock, do not use this tower fan with any solid-state speed control device.
• This appliance employs overload protection (fuse). If the fuse blows, unplug the product, replace the fuse as per user instructions, and check the appliance. If the replacement fuse blows, a short-circuit may be present; discard or return to an authorized service facility.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
• WARNING: Do not use replacement parts not recommended by the manufacturer (e.g., parts made at home using a 3D printer).

FOR HOUSEHOLD USE ONLY. READ AND SAVE THESE INSTRUCTIONS.

Gentle Reminder:

Check the appliance regularly and refer to TROUBLESHOOTING or contact customer support if you notice:

• Damaged power cord or plug.
• Loud noise, unusual smell, or excessive heat.

Specifications

2. Assembling Your Tower Fan

When using the appliance for the first time, remove the wraps and attach the parts by following the steps below:

1. Keep two base halves in a crossed position, then insert pegs on one half onto the slots on the other half.

   Diagram showing two base halves with slots and pegs, and arrows indicating insertion.

2. Press down on edges to click two base halves together.

   Diagram showing the two base halves being pressed together.

3. Run the cord through the center hole.

   Diagram showing the power cord being threaded through the base.

4. Fit the base onto the bottom of the fan by aligning the arrows on the underside.

   Diagram showing the base being attached to the fan bottom.

5. Rotate the base clockwise to lock in place.

   Diagram showing the base being rotated to lock.

6. Thread the cord through all REAR cord keepers before putting the fan upright.

   Diagram showing the cord being threaded through cord keepers.

Package Contents

• Control Panel
• LED Display
• Air Outlet
• Power & Plug
• Base
• User Manual
• Quick Start Guide
• Remote Control (Battery Included)
• Carry Handle / Remote Holder
• Air Inlet

3. Knowing Your Tower Fan

Control Panel

• Mode Button: Switch between Normal/Natural/Sleep/Auto Mode.
• Fan Speed Button: Adjust airflow volume (1-5 levels).
• Power Button: Turn power on/off.
• Timer Button: Select to set a timer (0-12h).
• Oscillation Button: Adjust airflow direction.
• Mute Button: Turn on/off button sounds.

LED Display

Displays Fan Speed / Timer Hour.

• Normal Mode
• Natural Mode
• Sleep Mode
• Auto Mode
• Mute
• Oscillation
• Timer

NOTE: Display will turn off after 1 minute (after 5 seconds in sleep mode). Wake up the display with any button. Display will not turn off when the auto on timer is enabled.

Getting the Most out of Your Tower Fan

1. It's not an air conditioner.
2. Remove any tall obstacles that might block the airflow from the fan.
3. Combine with your AC unit to get cooler air throughout the room.
4. Position the tower fan closer to you to get more direct airflow.
5. Place a bucket of ice in front of the fan for an extra cooling boost.

4. Using Your Tower Fan

General Operations

1. Touch ? to turn on, and ? to choose a working mode.
2. Touch ? to adjust the airflow volume.
3. Touch ? to change the airflow direction.
4. Touch ⏱️ to set a timer.
5. Touch ❌ to turn off the tower fan.

Working Modes

• Sleep Mode (Mute Auto On): Fan speed decreases every 30 minutes. Speed decreases by two levels at most and will remain constant if at level 1.
• Auto Mode: Fan speed adapts to the ambient temperature.
• Normal Mode: Fan runs at the constant speed.
• Natural Mode: Fan runs at alternating speeds.

Additional Features

• Timer: When the fan is ON/OFF, touch the timer button ⏱️ repeatedly to set a timer from 1 to 12 hours. When the timer ends, the fan will stop/start running automatically. To cancel, set the time to 0 hour. Note: When the auto off timer is enabled, display will return to fan speed after 3 seconds.
• Mute: Touch the mute button ? to turn on/off the button sounds.

If the fan is turned OFF or disconnected from power, it will operate under the previous settings (except the timer setting) when it is turned ON again.

Remote Control

• Power Indicator
• Decrease Fan Speed ➖
• Mode ?
• Oscillation ?
• Power ⚡
• Increase Fan Speed ➕
• Mute ?
• Timer ⏱️

5. Cleaning and Maintenance

Outer Surface

Gently wipe off the dust with a soft, dry cloth.

Base

Press on the lock sign here and rotate counterclockwise to release the base from the fan, then press the tabs on the edges to detach the base halves from each other.

Diagram showing how to detach the base halves.

Battery Replacement

1. Press the locking button to pop out the battery holder.
2. Replace with the same battery type with the (+) side facing up.
3. Push in the holder until securely locked into place.

Note: If the indicator on the remote control doesn't turn on any more, please consider replacing the battery.

This product contains a lithium button/coin cell battery. If swallowed or enters the body, it can cause severe internal burns and lead to death in as little as 2 hours. Always completely secure the battery compartment. If the compartment does not close securely, stop using the product, remove the battery, and keep it away from children. If batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

The cells must be disposed of properly, including keeping them away from children. Even used cells may cause injury.

Rear Grille

1. Remove the screw on the top of the rear grille with a Philips screwdriver.
2. Lift up the grille and pull it out.
3. Clean the dust on blades using a vacuum cleaner or air duster. Rinse the rear grille under running water or with a clean, damp cloth.
4. Dry up, then install the grille and the screw back in place, making sure the bottom pegs are fully inserted into the slots.

User Servicing Instructions (Fuse)

This appliance features a fused safety plug that protects against overload or short-circuit situations. If the fuse blows, please cut off power and follow the below instructions or consult a qualified electrician.

1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.
3. Remove fuse carefully. Push the fuse from the other side to remove the fuse.
4. Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse.
5. Close fuse cover. Slide closed the fuse access cover on top of attachment plug.

6. Troubleshooting

My fan won't turn on!

1. Make sure that the cord is connected to a powered outlet and the mains voltage corresponds with the voltage indicated on the fan.
2. Check if the fuse has blown. If the fuse has blown, please refer to page 13.

My fan is shaky and wobbling!

1. Place the fan on a flat, level surface.
2. Incorrect installation might also cause shakiness. Please refer to the assembly instructions in page 3-4. Note that the power cord must be run through all three keepers.

My fan is making vibration and noise!

1. Place the fan on a flat, level surface.
2. Be sure not to insert anything into the air inlet and outlet.

If your problem is not listed or still persists, please contact our Customer Support (see page 15).

7. Dreo Customer Care

Default 12-Month Warranty

This appliance is covered by Dreo warranty for 12 months from the date of its original purchase.

Extend Your Warranty

Extend your warranty by registering your new appliance on our website https://dreo.com/warranty.

The warranty will not apply in cases of:

1. Accident, misuse, or repairs performed by unauthorized personnel.
2. Any unit that has been tampered with or used for commercial purposes.
3. Normal wear and tear of wearable parts.
4. Use of force, damage caused by external influences.
5. Damage caused by non-observance of the User Manual, e.g. connection to an unsuitable mains supply or noncompliance with the instructions.
6. Partially or completely dismantled appliances.
7. Defects caused by or resulting from damages from shipping or from repairs, service, or alteration to the product or any of its parts that have been performed by a repair person not authorized by Dreo.

We can only provide after-sales service for products that are sold by Dreo or Dreo authorized retailers and distributors. If you have purchased the appliance from a different place, please contact your seller for return and warranty issues.

Shenzhen Hesung Innovation Technology Co., LTD

26F, Bldg A7, Creative City, Shenzhen, China

MADE IN CHINA

ETL US LISTED Intertek 5018396

Rev_1.1_EN