ASUS RT-BE86U WiFi Router Quick Start Guide

Hardware Explanations

I/O Ports Overview

The router features the following ports and controls on its rear panel:

• DCIN port: For connecting the power adapter.
• 10G WAN/LAN (Internet) port: A high-speed port for your internet connection or a 10 Gigabit LAN connection.
• USB 3.2 Gen 1 port (USB 3.0 port): For connecting USB storage devices or printers.
• USB 2.0 port: For connecting USB devices.
• WPS button: Press to initiate Wi-Fi Protected Setup.
• Reset button: Press and hold to restore factory default settings.
• LED button: Press to toggle the status LEDs on or off.
• Power switch: To turn the router on or off.
• 2.5G LAN 2-4 ports: Three Gigabit Ethernet LAN ports for connecting wired devices.

Specifications

LED Lights Overview

The router is equipped with several indicator lights to show its status:

• Power LED: Indicates the power status of the router.
• 2.4GHz LED: Indicates activity on the 2.4GHz Wi-Fi band.
• 5GHz LED: Indicates activity on the 5GHz Wi-Fi band.
• USB LED: Indicates activity on the USB ports.
• 10G LED: Indicates the status of the 10G port.
• WAN (Internet) LED: Shows the status of the internet connection.
• LAN LEDs: Indicate the connection status of the LAN ports.

Router Setup Steps

01 Prepare your Modem

Before connecting the router, prepare your existing modem:

1. Unplug the power cable from your modem. If it has a battery backup, remove the battery.
2. Connect your modem to the WAN port on the back of the ASUS RT-BE86U router using the provided network cable.
3. Plug the modem back into a power outlet and turn it on.
4. Check the modem's LED lights to ensure the internet connection is active.

02 Install your Router

Connect and power on the router:

1. Plug the power adapter into the router's DCIN port and press the Power switch.
2. The Power LED will illuminate, indicating that the hardware is ready for setup.

Note: If you are using DSL for your internet service, you will need to obtain your username and password from your Internet Service Provider (ISP) to properly configure the router.

Setup Methods

You can set up your router using either the ASUS Router mobile app or a web browser.

Via App

1. On your iOS or Android mobile device, go to your device's app store, search for "ASUS Router", and download the app.
2. Connect your mobile device to the default network SSID shown on the product label on the back of the router. Alternatively, you can scan the QR code on the product label to connect to the default network.
3. Launch the ASUS Router App and follow the on-screen instructions to complete the router setup.

The default Network Name (SSID) is typically "ASUS XX", where "XX" refers to the last two digits of the MAC address, which can be found on the label on the back of your router.

Or via Web Browser

1. Connect your computer to one of the router's LAN ports (LAN 2-4) at the back using an additional network cable. Alternatively, connect wirelessly to the network using the default SSID shown on the product label (e.g., "ASUS_XX").
2. Open a web browser on your connected computer or mobile device.
3. Navigate to http://www.asusrouter.com. The system may automatically redirect you to the ASUS Setup Wizard. If not, manually enter the address.
4. Follow the instructions provided by the ASUS Setup Wizard to complete the configuration.

Gain Another 10GE LAN Port

Set up 2.5GE WAN connection

To enable an additional 10 Gigabit LAN port, you need to configure the 2.5 Gigabit Ethernet (2.5GE) WAN connection:

1. Under factory default settings, connect your modem to the router's 2.5GE WAN port using a network cable.
2. When the ASUS Setup Wizard appears, select "Manual Setting".
3. In the wizard, choose "2.5G WAN" as the connection type. Follow the subsequent prompts to set up your Wi-Fi network name (SSID) and login credentials.

Start to Use

After completing the setup steps, the router will reboot briefly and then begin connecting to the internet via the 2.5GE port.

Frequently Asked Questions (FAQ)

Q1: Where can I find more information about the wireless router?

A1: For technical support and detailed product information, please visit the ASUS support website at https://www.asus.com/support. You can also find helpful video tutorials at https://qr.asus.com/wl_videotutorials.

Compliance and Safety Information

ASUS Recycling/Takeback Services

ASUS is committed to the highest environmental standards. Our recycling and takeback programs provide solutions for responsibly recycling our products, batteries, components, and packaging materials. For detailed recycling information specific to your region, please visit http://csr.asus.com/english/Takeback.htm.

REACH Compliance

In compliance with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, ASUS publishes information about chemical substances in its products. You can find this information on the ASUS REACH website at http://csr.asus.com/english/REACH.htm.

Federal Communications Commission (FCC) Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Prohibition of Co-location: This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirement, please follow operation instruction as documented in this manual. WARNING! This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 247 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This device is restricted for indoor use.

Innovation, Science and Economic Development Canada (ISED) Compliance

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. This device complies with CAN ICES-003(B)/NMB-003(B). Radio Frequency (RF) Exposure Information: The radiated output power of the ASUS Wireless Device is below the Innovation, Science and Economic Development Canada radio frequency exposure limits. The ASUS Wireless Device should be used in such a manner that the potential for human contact during normal operation is minimized. This equipment should be installed and operated with a minimum distance of 66cm between the radiator and any part of your body. This device has been certified for use in Canada. Status of the listing in the Innovation, Science and Economic Development Canada's REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h tt00020.html. Additional Canadian information on RF exposure also can be found at the following web: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html. The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit. The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate.

Safety Notices

Use this product in environments with ambient temperatures between 0°C (32°F) and 40°C (104°F). Refer to the rating label on the bottom of your product and ensure your power adapter complies with this rating. DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has been damaged. DO NOT place or drop objects on top and do not shove any foreign objects into the product. DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during electrical storms. DO NOT cover the vents on the product to prevent the system from overheating. DO NOT use damaged power cords, accessories, or other peripherals. If the Adapter is broken, do not try to fix it yourself. Contact a qualified service technician or your retailer. To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. DO NOT mount this equipment higher than 2 meters. The power supply cord(s) must be plugged into socket-outlet(s) that are provided with a suitable earth ground.