Alphacool Core GPU Block Series 10290

Important Information

This document provides instructions for the Alphacool Core GPU Block Series. Safety instructions and a digital guide are available in multiple languages (English, German, French).

Included Accessories

The following accessories are included with the GPU block:

• A: 9x M2x10mm Screw
• B: 1x 55x15x1mm Pad
• C: 2x 26x15x1mm Pad
• D: 1x 83x8x1mm Pad
• E: 3x 15x8x1mm Pad
• F: 3x 8x8x1mm Pad
• G: 1x Thermal Grease
• H: 1x Putty tool
• I: 1x 55x8x3mm Pad
• J: 2x 26x8x3mm Pad
• K: 1x 45x45x3mm GPU-Pad
• L: 1x 20x8x3mm Pad
• M: 1x PCI Bracket
• N: 1x Washer
• O: 1x M2x5mm Screw
• P: 1x ARGB Adapter
• Q: 2x G1/4 Plug
• R: 1x Plug tool
• S: 1x Screwdriver

Compatibility Check and Preparation

Check Compatibility

Before assembling the cooler, compare your graphics card with the images in the Alphacool configurator at https://gpu.alphacool.com. Search for your specific graphics card or cooler model. You can also compare the PCB number for definitive identification, as the cooler is designed for a specific PCB layout. Be aware that graphics card manufacturers may revise their designs, which could lead to incompatibility with later models. During assembly, ensure that taller components have sufficient clearance and that the cooler does not damage your graphics card.

Alphacool International GmbH is not liable for assembly errors resulting from negligence, such as selecting an incompatible cooler.

Prepare Graphics Card

Place your graphics card hardware on an antistatic mat. Begin by dismantling the original cooler. Depending on the cooler's construction, you may need to remove screws from the back of the card and carefully disconnect the fan connector. If the original cooler uses thermal glue, proceed with extreme caution to avoid damaging components. Handle all parts carefully. After dismantling, clean the hardware of any thermal paste or pad residues using a solvent, such as isopropanol alcohol.

Step 1: Remove Transport Spacer

This step involves removing a transport spacer from the graphics card assembly. The visual depicts a graphics card PCB with a spacer being detached.

Step 2: Place Thermal Pads on Cooling Block

This step guides the placement of thermal pads onto the cooling block. The visual indicates specific areas on the cooling block where the thermal pads should be applied.

Assembly Instructions

Apply Thermal Grease

Apply the provided thermal grease (G) to the GPU die and other necessary contact points on the cooling block using the putty tool (H).

Install PCB

Carefully align and place the graphics card PCB onto the cooling block assembly, ensuring it is seated correctly.

Place Thermal Pads on PCB Backside

Apply the thermal pads (L, K) to the backside of the graphics card PCB. Place them on components such as VRMs and memory chips as shown in the diagram.

Install IO-Shield and Mount Backplate

Attach the IO-shield to the graphics card. Mount the backplate to the graphics card assembly using the provided screws (A, S, N, M) and the screwdriver (S).

Connect ARGB Lighting

Connect the ARGB adapter (P) to the ARGB header on the graphics card and to the appropriate ARGB controller or motherboard header for customizable lighting effects.

Screw in Screw Plugs with Tool

Utilize the plug tool (R) to securely screw in the G1/4 plugs (Q) into the designated ports on the cooling block.

Need Help?

For assistance or further information, please contact Alphacool International GmbH:

Alphacool International GmbH
Marienberger Str. 1
D-38122 Braunschweig
Germany

Support: +49 (0) 531 28874-0
Fax: +49 (0) 531 28874 - 22
E-Mail: info@alphacool.com
Website: https://www.alphacool.com

We care!