INBAY Wireless Charging Tray Installation Guide

Installation Overview

This guide provides step-by-step instructions for installing the INBAY wireless charging tray in your Renault Kadjar. Please follow all instructions carefully to ensure proper installation and safe operation.

Difficulty Level: Low to High (depending on user experience)

Important Safety Information

• Ensure correct wiring and connections.
• Route cables carefully to prevent kinking, crimping, or damage.
• Keep cables away from moving parts and ensure they do not become entangled.
• INBAY is not liable for damages caused by improper installation or utilization.
• Use only the supplied mounting material.
• Technical modifications are reserved; no responsibility is accepted for the accuracy of this information.
• The "Qi" symbol is a trademark of the "Wireless Power Consortium".
• CAUTION: Do not place any other objects such as coins, credit cards, etc., onto the INBAY surface. Especially smartphones with attached ring stand holders should not be used.
• CAUTION HOT! Surface temperature can reach up to 55°C.
• CAUTION: Do not operate devices/consumers with more than 5A / 60W on the +12V socket. Otherwise, a risk of overvoltage can occur!

Installation Steps

The installation involves disassembling parts of the center console and connecting the charging tray to the vehicle's power supply.

Step 1: Accessing the Console Area

Begin by carefully removing trim pieces around the gear shift and center console. This may involve using a trim removal tool to gently pry components loose.

Visual Description: The images show hands using tools to carefully remove plastic trim pieces from the car's center console, revealing internal components and wiring.

Step 2: Unscrewing Components

Locate and remove screws securing the center console panels. The images indicate the use of a TX30 screwdriver for specific screws.

Visual Description: Close-up shots show a TX30 screwdriver being used to remove screws from the console, with circular highlights indicating the screw locations.

Step 3: Disconnecting and Removing Panels

Carefully disconnect any electrical connectors attached to the panels being removed. Gently pull panels away from the console.

Visual Description: Hands are shown disconnecting electrical connectors and pulling away sections of the center console trim. Arrows indicate the direction of removal.

Step 4: Preparing the Installation Site

A hole of approximately 10 mm diameter needs to be drilled in the designated area of the center console to route the power cable.

Visual Description: A hand is shown using a drill with a 10mm drill bit to create a hole in the car's console. An eye symbol with "Ø = ca. 10 mm" indicates the required hole size.

Step 5: Routing the Power Cable

Route the power cable from the charging tray through the newly drilled hole and towards the vehicle's power source.

Visual Description: The images show the power cable being threaded through the hole and routed underneath the console, with arrows indicating the path.

Step 6: Connecting the Power Cable

Connect the INBAY charging unit's power cable to the appropriate connector within the vehicle's wiring harness. The images show specific connectors being plugged together.

Visual Description: Close-up images show the power connector from the INBAY unit being plugged into a corresponding connector in the car's wiring harness. A green checkmark symbol indicates a successful connection.

Step 7: Installing the Charging Tray Unit

Place the INBAY wireless charging tray into the prepared space in the center console. Ensure it sits flush and securely.

Visual Description: The charging tray is shown being placed into the console opening. Arrows indicate the placement points.

Step 8: Reassembling the Console

Reinstall all removed trim pieces and panels, ensuring all electrical connectors are reconnected and screws are tightened.

Visual Description: The images show the process of reassembling the center console panels, reversing the disassembly steps.

Step 9: Final Check and Operation

Once assembled, test the wireless charging functionality. A red LED indicates standby mode, and a blue LED indicates that a device is charging.

Visual Description: The top image shows the charging pad with a red LED illuminated (standby). The bottom image shows a smartphone placed on the pad with a blue LED illuminated, indicating charging.

Troubleshooting and Warnings

• Do not place metal objects (coins, credit cards, key rings) on the charging surface as they can cause overheating or damage.
• Smartphones with attached ring stands should not be used.
• Ensure the power source does not exceed 5A / 60W.

Important Post-Installation Note

After installation, this manual must be placed in the glove compartment of the customer's car.