PRYMEBLU BTH-600 Wireless BT Speaker Microphone User Manual

Introduction

This document provides information on the PRYMEBLU BTH-600 Wireless BT Speaker Microphone, its features, operation, and specifications.

Controls and Connections

Front Firing Speaker

Receives audio for calls. Volume controlled by microphone buttons or radio/phone.

PTT Button

Activates push-to-talk for the 2-way radio.

Clothing Clip

Secures the microphone to clothing. Rotatable for optimal positioning.

Microphone

Picks up user's voice for outgoing calls.

Volume Up and Down Buttons

Adjusts receive audio volume in five preset steps.

Status LEDs

Red and blue LEDs indicate device status. ?

Phone Button

Answers or hangs up phone calls when connected to a cellphone. ?

Earphone Jack

3.5mm jack for optional wired listen-only earphones. ?

Charge Jack

Mini-USB port for recharging the battery. ?

Battery Cover

Rear cover secured by a thumbscrew, allows access to the removable battery. ?

Multifunction Button

Turns the device on/off (hold for 1 second) and initiates pairing mode.

Removable Battery

The device is powered by a removable Lithium battery pack.

Charging the Speaker Microphone

The BTH-600 uses a rechargeable Lithium-Ion battery pack that requires charging before use and regularly thereafter. A full charge provides up to 40 hours of operation, though this can vary.

To Charge:

1. Ensure the device is off.
2. Connect the charge cable to a powered USB outlet and then to the charge jack.
3. A constant red LED indicates charging.
4. Typical charge time is approximately 5 hours.
5. The LED turns off when charging is complete.
6. Disconnect the charger once fully charged.

Charging Cautions:

• Do not use damaged chargers or cables. Contact PRYME for replacements.
• Do not tamper with or modify the device or charger.
• Always turn the device off when charging.

Installing or Replacing the Battery Pack

The BTH-600 is powered by a rechargeable Lithium-Ion battery pack, designed for over 1,500 charge/discharge cycles.

To Access Battery Compartment:

1. Loosen the thumbscrew counter-clockwise to open the cover. Remove the battery door.
2. Insert the rechargeable battery pack, aligning terminals with contacts.
3. Reinstall the cover and tighten the thumbscrew clockwise. Do not overtighten.

Pairing Procedures

Pairing with a PRYMEBLU Radio Adapter or 2-Way Radio

Ensure the Speaker Microphone is powered off before starting.

1. Hold the Multifunction Button for approximately 3 seconds until the LED flashes RED-BLUE-RED-BLUE repeatedly (pairing mode).
2. For PRYMEBLU adapters: Put the adapter into pairing mode per its manual.
3. For Icom or Kenwood radios: Follow manufacturer instructions to scan for devices and select the PRYMEBLU microphone.
4. Devices will sync. The LED will show one blue flash every few seconds upon successful pairing.
5. If the adapter does not detect the microphone within 60 seconds, it will exit pairing mode.
6. Once paired, the 2-way radio can be operated via the Speaker Mic.

Reconnecting a Previously Paired Device

Paired devices will attempt to re-establish their link when powered on and within range. This can take 10-60 seconds.

Pairing with a Cellphone

Ensure the Speaker Microphone and other BT devices are powered off before starting.

1. Hold the Multifunction Button for approximately 3 seconds until the LED flashes RED-BLUE-RED-BLUE repeatedly (pairing mode).
2. Activate Bluetooth on your phone and scan for new devices.
3. Select the PRYMEBLU Speaker Microphone from the list. Enter "0000" if prompted for a passcode.
4. Devices will sync. The LED will revert to a single blue flash every few seconds.
5. Once paired, you can make and receive calls using the Speaker Microphone.

Using the PRYMEBLU Speaker Microphone

After pairing with an adapter or cellphone:

• Received signals play through the front speaker or optional earphone. Volume is adjustable.
• The microphone picks up your voice for transmitting or phone calls.
• Push-to-Talk (PTT) can be activated via the PTT button on the mic, the adapter's talk button, a wired PTT, or an optional PRYMEBLU Wireless BT PTT (BT-PTT2).
• To answer/hang up calls, press the Phone Button or use the phone interface.
• Press and hold the Phone Button for 3 seconds to activate voice dialing (when not connected to a 2-way radio).

Note: When on a phone call, 2-way radio signals are not heard. Pressing the PTT button during a phone call will transmit on the radio but will not send audio from the microphone.

Status LED Messages

Optional Earphones

For enhanced privacy, listen-only earphones with a 3.5mm audio plug can be used. The front speaker is disabled when an earphone is connected.

PRYME offers various listen-only earphones, such as the EH-1389SC model (sold separately).

Specifications

Support and Warranty

PRYME Radio Products provides a one-year limited warranty against defects in materials or workmanship from the date of retail purchase. This warranty applies to consumers in the United States and Canada and covers repair or replacement of defective units at PRYME's option. It does not cover damage from misuse, accidents, improper installation, or unauthorized repairs. For support or warranty service, contact PRYME at 1-800-666-2654 or visit www.PRYME.com.

Copyright and Trademark Information

© 2021 PRYME Radio Products, Brea CA. All rights reserved.

PRYME® and PRYMEBLU® are trademarks of PRYME Radio Products.

Icom is a trademark of Icom Inc.

Kenwood is a registered trademark of JVCKENWOOD Corporation.

Android is a trademark of Google Inc.

All other product or service names are the property of their respective owners.

Disclaimer: The BT wireless link used by PRYMEBLU products is an open, unsecured standard. It is not recommended for first-responder or mission-critical users.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting.

RF Exposure Warning! This device contains transmitters and receivers which emit Radio Frequency (RF) energy. The device is designed to comply with the limits for exposure to RF energy set by the Federal Communications Commission (FCC) of the United States, Industry Canada (IC) of Canada, and the regulating entities of other countries. If you are still concerned about exposure to RF energy, you can further limit your exposure by limiting the amount of time you use the equipment or by placing more distance between your body and the device, since exposure level drops off dramatically with distance.