Product Overview
This document provides instructions, safety guidelines, and calibration procedures for the VEVOR Table Saw Miter Gauge. It is designed for use with table saws to ensure accurate angled cuts.
The product is suitable for 3/4 inch diagonal miter slots.
Safety First
Always read and understand all safety materials before operating power tools or machinery. Follow all safety guidelines provided by the manufacturer.
Safety Guidelines
WARNING: Failure to follow instructions may result in electric shock, fire, or serious injury. The term "power tool" refers to both corded and cordless tools.
Work Area Safety
- Keep the work area clean and well-lit.
- Do not use power tools in dangerous, damp, wet, or explosive environments.
- Keep children and bystanders away.
- Make your workshop child-proof.
Electrical Safety
- Ensure power tool plugs match the outlet; do not modify plugs or use adapters with grounded tools.
- Ground electric tools properly.
- Avoid contact with grounded surfaces.
- Do not expose tools to rain or wet conditions.
- Do not abuse power cords; keep them away from heat, oil, sharp edges, and moving parts.
- Use appropriate, heavy-duty extension cords in good condition.
Precision Miter Gauge System Safety
- Read this manual and manufacturer's safety guidelines for the tool you are using the accessory with.
- Ensure handles and T-knobs are secure before operation.
- Keep hands away from moving blades or bits; turn off the tool and wait for it to stop before clearing debris.
- Always support long boards on both infeed and outfeed ends.
- Securely hold workpieces against the machine table and miter gauge/fence.
- This miter gauge system is designed for a specific application; do not modify or use it for other purposes.
WARNING: This product can expose you to chemicals, including Acrylonitrile, known to cause cancer and reproductive harm in California. For more information, visit www.P65Warnings.ca.gov.
Calibration
Generally, the Miter Gauge is ready out of the box. If calibration is needed, follow these steps:
- Release the fixed knob and handle: Loosen the handle counterclockwise, lift the metal knob, and rotate it 90 degrees to release.
- Set Index to Zero: With the locking pin engaged, adjust the miter gauge head to zero on the index point. [Image: Miter gauge head showing index point and locking mechanism]
- Square it Up: Place a square against the miter bar (1), then slide it against the face of the miter gauge (2). Set the miter gauge face to be 90 degrees to the miter bar. [Image: Diagram showing a square being used to check 90-degree alignment]
- Lock the knob mechanism and tighten: Tighten the handle to maintain the pan tilt position, then rotate the metal knob into the card slot. [Image: Hand tightening the miter gauge knob]
- Adjust The Plungershandle: Use a hex key wrench to push plungers outward or draw them inward to achieve the correct fit for your table saw slot. Comment: Do not over-extend plungers, as this can prevent smooth sliding and damage them. [Image: Hand using a hex key wrench to adjust plungers]
- Ready to Go: Your Miter Gauge is now calibrated and ready for use. [Image: Fully assembled VEVOR Table Saw Miter Gauge]
Aluminum Miter Fence Installation
Many miter gauges are pre-drilled to accept miter fences. Align bolts with holes and secure the fence using supplied bolts, washers, and T-knobs.
Why Use a Miter Fence?
Using a miter fence provides better support for your stock during cuts.
- Factory Miter Gauge: Shows a large unsupported gap between the blade and the gauge.
- Miter Gauge with fence: Shows the stock fully supported when using the fence.
Flip Stop Installation
The flip stop is ideal for repetitive length cuts. It slides into the top track of the aluminum fence and is secured with a T-knob.
Ensure your stock always contacts the flip stop on the outside of the arm for minimal play. The flip stop can be reversed if necessary by disassembling and reassembling the unit.
[Image: Flip stop installed on the fence, holding a piece of wood. Text overlay: "Always Keep Your Stock On The Outside Of The Stop Arm"]
Product SKUs and Inventory
The VEVOR Table Saw Miter Gauge is available in several configurations:
SKU1: Table Saw Oblique Cutting Gauge without Support
Range: -60° to +60°
| Item | Quantity |
|---|---|
| Adjustment plate & sliding bar (assembled) | 1 |
| Handle | 1 |
| Grating limiter | 1 |
| Hex wrench (4mm) | 1 |
| Hex wrench (2mm) | 1 |
| Instruction manual | 1 |
[Image: Miter gauge and accessories for SKU1]
SKU2: Table Saw Oblique Cutting Gauge with Support
Range: -60° to +60°
Backing length: 18" (460mm)
| Item | Quantity |
|---|---|
| Backing Mountain | 1 |
| Diagonal cutting gauge (metal adjustment plate & sliding bar, assembled) | 1 |
| Handle | 1 |
| Grating limiter | 1 |
| Hex wrench (4mm) | 1 |
| Hex wrench (2mm) | 1 |
| Instruction manual | 1 |
[Image: Miter gauge with 18" backing and accessories for SKU2]
SKU3: Table Saw Oblique Cutting Gauge with Support
Range: -60° to +60°
Backing length: 24" (610mm)
| Item | Quantity |
|---|---|
| Backing Mountain | 1 |
| Diagonal cutting gauge (metal adjustment plate & sliding bar, assembled) | 1 |
| Handle | 1 |
| Grating limiter | 1 |
| Hex wrench (4mm) | 1 |
| Hex wrench (2mm) | 1 |
| Instruction manual | 1 |
[Image: Miter gauge with 24" backing and accessories for SKU3]
SKU4: Table Saw Oblique Cutting Gauge with Support
Range: -60° to +60°
Backing length: 19-35" (490-890mm)
| Item | Quantity |
|---|---|
| Backing Mountain | 1 |
| Diagonal cutting gauge (metal adjustment plate & sliding bar, assembled) | 1 |
| Handle | 1 |
| Grating limiter | 1 |
| Hex wrench (4mm) | 1 |
| Hex wrench (2mm) | 1 |
| Instruction manual | 1 |
[Image: Miter gauge with 19-35" backing and accessories for SKU4]
Diagrams
Disassembled diagram of herringbone scale parts: Shows handle, blade, and Spring Jimmy screws.
[Image: Disassembled miter gauge scale parts]
Display of the range of division values for the herringbone scale: Shows various angle settings on the scale.
[Image: Close-ups of the miter gauge scale showing different angle divisions]
Company Information
Manufacturer Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi, Shanghai
Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREET, EASTWOOD, NSW 2122, Australia
Imported to USA: Sanven Technology Ltd., Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
EC REP: SHUNSHUN GmbH, Römeräcker 9 Z2021, 76351 Linkenheim-Hochstetten, Germany
UK REP: Pooledas Group Ltd, Unit 5 Albert Edward House, The Pavilions, Preston, United Kingdom
Made In China
