GE 7.4 cu. ft. Capacity with Sensor Dry Electric Dryer

Dimensions and Installation Information (in Inches)

Electric Dryer Rating:

• 240V 5600W 24A 60Hz
• 208V 4400W 22A 60Hz

Exhaust Option:

4-way rear, right, left and bottom

Circuit Requirements:

An individual, properly-grounded branch circuit, protected by a 30-amp circuit breaker or a time-delay fuse, is required.

Note on Dryer Wall Outlet:

Dryer wall outlet must be located within 36" of service cord entry and accessible when dryer is mounted in position.

Installation Information:

For complete information, see installation instructions packed with your dryer.

Special Installation Requirements

Alcove or Closet Installation:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0" either side; 1" front, top and rear.
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

Bathroom or Bedroom Installation:

• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

Minimum Clearances Other Than Alcove or Closet Installation:

• Minimum clearances to combustible surfaces are: 0" both sides; 1" rear.

Dryer Exhausting Information:

Use metal duct only, vertical and horizontal ducting.

Diagram Description: Side and Rear Views with Dimensions

• Side View: Width 22-1/2 inches, Depth 30-1/2 inches, Height 46 inches (overall), 38-1/2 inches (cabinet).
• Rear View: Width 27 inches, Depth 27 inches (cabinet), Power Cord 5 inches, 11-3/4 inches from top.
• Clearances indicated: 8 inches (top), 1-3/4 inches (side), 3-1/4 inches (bottom).

For answers to your Monogram, GE Café™, GE Profile™ or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.

Listed by Underwriters Laboratories.

Specification Revised 12/22

Ducting Materials and Exhausting

For complete information, see installation instructions packed with your dryer.

Ducting Materials:

For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting.

Exhaust Length Calculation:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.

Dryers must be exhausted to the outside.

Caution:

For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down.

Dryer Exhausting Information:

Use metal duct only, vertical and horizontal ducting.

Diagram Description: Exhausting Information

Diagrams illustrate exhaust hood types and maximum vent lengths based on the number of 90° turns (A and B measurements are shown in the diagram).

For every extra 90° elbow, reduce the allowable vent system length by 10 ft. Two 45° elbows will be treated like one 90° elbow. For the side exhaust installations, add one 90° elbow to the chart. When calculating the total vent system length, you must add all the straight portions and elbows of the system (including the transition duct).

For more information on venting kits and accessories, please call 1-800-GE-CARES.

Specification Revised 12/22

Features and Benefits

Sensor Dry:

This dryer with moisture sensor continually monitors temperature and moisture to determine the appropriate drying time to protect your laundry and prevent over-drying.

My Cycle Setting:

Make laundry simpler by saving your favorite wash settings as a preset for future use with the My Cycle setting.

Eco Dry:

Energy saving option reduces dry temperatures on select cycles without sacrificing performance.

High Performance Venting:

Powerful airflow offers long-lasting performance from lint build-up and offers venting solutions up to 120 feet for greater installation flexiablity.

Wrinkle Care:

Minimize wrinkles with an extended tumble dryer that will continue to tumble with no heat to keep wrinkles from setting in after the dry cycle is complete.

Damp Alert:

Immediately know when clothes reach the ideal dampness level for ironing or air drying with this Damp Alert dryer.

Custom Dry Settings:

10 custom dryer settings support a variety of specialty settings to protect clothing from unnecessary wear and tear.

Model:

GTD58EBPVDG – Diamond Gray

Control Panel Description: The dryer features a control panel with options including: Mixed Load, Delicates, Normal, Cottons, Sanitize, Active Wear, Quick Dry, Towels, Bulky Bedding, Air Fluff, Timed Dry, Pause, Controls, Sensing, Clean Lint Filter, Damp Alert, Delay Drying, Cooling, Done, Time (More Time, Less Time), Level (More Dry, Dry, Less Dry, Damp), Temp (High, Medium, Low, No Heat), Wrinkle Care, Control Lock, Sound Delay, Eco Dry, My Cycle.

Listed by Underwriters Laboratories.

Specification Revised 12/22