Klarstein Spin Doctor Ceiling Fan

Introduction

Congratulations on purchasing the Klarstein Spin Doctor ceiling fan. This manual provides essential information for safe installation and operation. Please read these instructions carefully to prevent potential damage. Klarstein assumes no liability for damage caused by disregard of instructions or improper use.

Scan the QR code (if available in the original document) for the latest user manual and additional product information.

Technical Data

Safety Instructions

• Never attach the fan to a power outlet; attach it directly to the ceiling.
• The minimum distance between the fan blades and the floor must be more than 2.3 meters (7.5 feet).
• The minimum load capacity of the hook from which the fan is hung must be 100 kg (220 lbs).
• Ensure installation of a double-pole disconnection switch with a contact separation of at least 3 mm between poles in the supply wiring to the ceiling fan.
• Switch off the power supply before connecting any wires.
• Electrical wiring must comply with local regulations.
• The fan must be properly earthed to avoid the risk of electric shocks.
• Never mount the fan in a moist or wet room.
• Be careful when working near the rotating blades.

Note: Always have your fan installed by someone knowledgeable about electrical wiring.

Installation

Follow these steps for installation:

1. Step 1: Mount the Bracket

   Locate and mark the center of the ceiling joist. Pass the power cable through the hole in the mounting bracket. Secure the mounting bracket to the ceiling joist using flat washers, spring washers, and wood screws.

   [Diagram shows locating ceiling joist, passing wire through bracket, and screwing bracket to joist.]

2. Step 2: Hang the Fan

   Hang the fan cover onto the bracket hook using one of the holes at the top of the upper canopy screws.

   [Diagram shows hanging the fan cover onto a hook on the mounting bracket.]

3. Step 3: Connect Wires

   Connect the wires from the power source to the wiring terminals as follows:

   • Brown wire: "L" (Live)
   • Blue wire: "N" (Neutral)
   • Green/Yellow wire: [ground symbol] (Earth)
   [Diagram shows wire connections to terminals: L, N, and Earth symbol.]

4. Step 4: Secure the Canopy

   Lift the fan canopy until the screws reach the bottom of the slots. Rotate the canopy counterclockwise until the screws drop into the slot recesses.

   [Diagram shows lifting the canopy and rotating it to engage screws in slots.]

5. Step 5: Final Canopy Attachment

   Insert the remaining set screws and washers. Tighten all screws securely. Ensure the canopy is firmly attached and no wires are trapped.

   [Diagram shows inserting and tightening set screws for the canopy.]

6. Step 6: Install Fan Blades

   Attach the fan blades to the motor using the provided screws and spring washers.

   [Diagram shows attaching fan blades to the motor.]

7. Step 7: Connect Speed Regulator

   Remove the speed regulator cover. Feed the wires through the cable entry and connect them as shown in the diagram. Mount the regulator on a wall using a suitable base block.

   [Diagram shows wiring connections for the speed regulator, motor, and power supply.]

Use and Operation

• Turn on the electricity before operating the fan.
• The fan starts when the three-speed switch, connected by an extension chain to the motor housing, is activated.
• The fan operates at three different speeds by pulling the extension chain:
  • First pull: HIGH SPEED
  • Second pull: MEDIUM SPEED
  • Third pull: LOW SPEED
  • Fourth pull: OFF

Disposal Considerations

If your country has legal regulations for the disposal of electrical and electronic devices, the symbol on the product or packaging indicates that it must not be disposed of with household waste. Instead, it must be taken to a collection point for recycling electrical and electronic equipment. Proper disposal protects the environment and human health from negative consequences. For information on recycling and disposal, contact your local authority or household waste disposal service.

Manufacturer & Importer (UK)

Manufacturer: Klarstein, Chal-Tec GmbH, Wallstraße 16, 10179 Berlin, Germany.

Importer for Great Britain: Chal-Tec UK limited, Unit 6 Riverside Business Centre, Brighton Road, Shoreham-by-Sea, BN43 6RE, United Kingdom.