Instructions for ELSEMA models including: PCR433WG 433MHz Penta Receiver with Wiegand Output, PCR433WG, 433MHz Penta Receiver with Wiegand Output, Penta Receiver with Wiegand Output, Wiegand Output
Wiegand Receiver | Access Control | PentaCODE remotes | Elsema
ELSEMA 433MHz Receiver Wiegand Output PCR433WG Wiegand Output Penta Receiver 433MHz Penta Receiver with Wiegand Output Features Easy to add remote controls to any Wiegand input access control panel Remotes are added like cards or RFID tags with no software changes Wireless keyless entry offers convenience, security and safety for accessing gates, doors and boom gates Wide operating supply voltage and low current consumption Easy way to facilitate for handicapped access Compatible with PentaCODE® remotes Easy to use dipswitch coding PCR433WG Applications Keyless access control for automatic gates, doors and boom gates Description This receiver allows you to add wireless remote controls to your existing access control systems by connecting the PCR433WG receiver to the access system. The remote controls have a range of up to 200 metres (650 feet) and are available with 2 or 4 buttons. The extra buttons can be used as a panic button allowing a single remote to allow access control and panic alert system. The receivers Wiegand output interfaces to virtually any commercial access control panel. Remote controls are added as easily as Wiegand cards or RFID tags without any software changes. The ID and facility codes can be matched to the system requirements. The receiver has a bi-colour LED to act as a status display. Red LED indicates that AC or DC power is "On" and Green LED indicates remote control signal has been received. Setup Instructions The Penta receiver has a 12-way dipswitch, where switches 1-8 sets the site code. Dip Switch 10, 11 & 12 selects the button that the PCR433WG receives from the PentaCODE® Remote. Receiver dip-switch setting Remote Button 10 11 12 All Off Off Off 1 Off Off On 2 Off On Off 3 Off On On 4 On Off Off The user code is set by the 12-way dipswitch on the remote. Each remote should have a unique code to identify each user. Remotes are programmed into the access controller in the same way as RFID tags. When programming instead of swiping the RFID tags, the remote button is pressed. On the PentaCODE® remotes you need to have at least 1 of the 12 switches "On" for the remote to work. The receiver comes pre-wired in a small 70 x 55 x 25 mm enclosure and a supply of 12 to 24 Volts AC or DC can be connected. ELSEMA 433MHz Receiver Wiegand Output PCR433WG The 26 bit Wiegand data output from the PCR433WG is as shown below. You can change the 12 way Dip Switch on the transmitter to change the serial code. However each button on the transmitter will send a different code. Site Code: Dip Sw 1-8 on Receiver (PCR433WG) Serial Code: Dip Sw 1-12 on Tx + Button Pressed Bit 1 = Leading Parity Bit Bit 2 = Receiver Dip Switch 8 Bit 3 = Receiver Dip Switch 7 Bit 4 = Receiver Dip Switch 6 Bit 5 = Receiver Dip Switch 5 Bit 6 = Receiver Dip Switch 4 Bit 7 = Receiver Dip Switch 3 Bit 8 = Receiver Dip Switch 2 Bit 9 = Receiver Dip Switch 1 Bit 10 = Transmitter Button 4 Bit 11 = Transmitter Button 3 Bit 12 = Transmitter Button 2 Bit 13 = Transmitter Button 1 Bit 14 = Bit 15 = Bit 16 = Bit 17 = Bit 18 = Bit 19 = Bit 20 = Bit 21 = Bit 22 = Bit 23 = Bit 24 = Bit 25 = Transmitter Dip Switch 12 Transmitter Dip Switch 11 Transmitter Dip Switch 10 Transmitter Dip Switch 9 Transmitter Dip Switch 8 Transmitter Dip Switch 7 Transmitter Dip Switch 6 Transmitter Dip Switch 5 Transmitter Dip Switch 4 Transmitter Dip Switch 3 Transmitter Dip Switch 2 Transmitter Dip Switch 1 Bit 26 = Trailing Parity Bit Products in the Range ELSEMA 433MHz Receiver Wiegand Output PCR433WG PCR43301RE 1-Channel Receiver with Relay Output. Enclosed in a case PCR43302P 2-Channel Plug in type Receiver with Open Collector Output PCR43302R PCR43302RE 2-Channel Receiver with 2-Channel Receiver with Relay Outputs Relay Outputs. Enclosed in a case PCR43301240R PCR43301240RE PCR43302240R PCR43302240RE 1-Channel Receiver with 1-Channel Receiver 2-Channel Receiver with 2-Channel Receiver 240VAC mains supply enclosed in an IP66 case 240VAC mains supply enclosed in an IP66 case PCR43304R PCR43304RE PCR43305R PCR43305RE 4-Channel Receiver with 4-Channel Receiver 5-Channel Receiver with 5-Channel Receiver Relay Outputs enclosed in an IP66 case Relay Outputs enclosed in an IP66 case LED Indicator Led color RED Flashing RED On Green ON Status Power up Receiver is ready PentaCODE transmitter code received Technical Data ELSEMA 433MHz Receiver Wiegand Output PCR433WG Supply Voltage 12 24 Volts AC or DC. Can use Elsema's AC power pack (12PP-1000) Standby Current 28mA stand by at 24VDC Wiegand Format 26 bits, other formats available upon request Frequency Band 433.100 to 434.700MHz Operating Temperature Range -5 to 50°C Connections 50cm Flying leads for supply and Wiegand output. See block diagram Antenna ANT433 series for long range applications. Antenna wire for short range applications Dimensions 70mm x 55mm x 25mm. Weight 70 grams Operating Range up to 200 metres depending on building structure and receiver antenna Useable Transmitters PCK series "PentaCODE®" remotes Block DiagramElsema Pty Ltd Adobe PDF Library 24.5.96