Behringer ULTRALINK ULM202USB/ULM200USB Quick Start Guide
High-Performance 2.4 GHz Digital Wireless System with 2 Handheld Microphones and Dual-Mode USB Receiver
Hook-Up Diagram
The diagram illustrates how to connect the Behringer ULTRALINK ULM202USB/ULM200USB system. It shows the ULM200D USB receiver connecting to a laptop or a Behringer XENYX QX2442USB mixer. The two ULM200M handheld microphones are shown wirelessly connected to the ULM200D receiver. Another configuration shows the ULM200D receiver connecting to a Behringer B115MP3 powered speaker.
Controls
ULM200M Microphone
Model: ULM200M
- 1. POWER/STATUS LED
- 2. VOLUME Button (Mute/volume down) ▼
- 3. VOLUME Button (Power on/unmute/volume up) ▲
ULM200D Receiver
Model: ULM200D
- 4. USB connector
- 5. Wireless Link Status LED
Getting Started
- Connect the ULM200D wireless receiver to the “WIRELESS ONLY!” USB connector on wireless-enabled Behringer mixers, powered speakers or other compatible products, or to a USB port on a computer.
- Press and hold the ▲ button on the ULM200M wireless microphone to connect wirelessly to the ULM200D receiver. The LED on the microphone will flash slowly during the connecting sequence and will light solid once connected. If the ULM200M wireless microphone cannot connect to a receiver, the microphone will automatically power down after 10 seconds.
- Once connected, the ULM200M microphone will be set at a medium volume. Use the ▲ and ▼ buttons to adjust the volume.
- A long press of the ▼ button will put the ULM200M microphone into mute. The mute condition is indicated by rapid flashing of the LED. If the user does not unmute within 60 seconds, the ULM200M microphone will power down to save battery life.
- A short press of the ▲ button will unmute the ULM200M microphone. If the ULM200M microphone is unmuted more than 10 seconds after muting, it will return to the previous volume level, if unmuted after less than 10 seconds it will be set to the minimum volume level.
- Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone will power down 10 seconds after the ULM200D wireless receiver is unplugged.
- The LED in the ULM200M wireless microphone will indicate when the battery is low by regular brief flashes.
- Should the ULM200M wireless microphone become unpaired with the ULM200D wireless receiver, the microphone can be re-paired from the powered down state by simultaneously pressing the ▲ and ▼ buttons and moving the microphone to within 10 cm (4 inches) of the ULM200D wireless receiver. The LED on the microphone will flash slowly during the pairing sequence and will light solid once connected. If the ULM200M wireless microphone cannot pair to the receiver it will automatically power down after 10 seconds.
Specifications
| Feature | Value |
|---|---|
| RF output | <20 dBm (100 mW) |
| Operating range | 120 m (Line of Sight)* |
| Dynamic range | 92 dB, A-weighted** |
| Equivalent input noise | -112 dBu |
| Frequency Response (Wireless Link) | 20 Hz - 20 kHz, ±1 dB** |
| Sampling rate | 48 kHz |
| Resolution | 24-bit |
| Encoding | 232 kbps SLAC (Slightly Lossy Audio Codec) |
| Latency | 14.5 ms |
| RF frequency | 2.4 GHz ISM band (2406 MHz - 2474 MHz), 18 channels |
| USB current consumption | 70 mA @ 5 VDC |
| Battery type | 2 x AA (LR6) Alkaline cells |
| Battery life | 30 hours |
| Dimensions (W x D x H) | 45.7 x 45.7 x 243.8 mm (1.8 x 1.8 x 9.6") |
| Weight | |
| ULM200USB | 0.2 kg (0.4 lbs) |
| ULM202USB | 0.4 kg (0.9 lbs) |
*Achievable range will be dependent on nearby sources of RF interference and/or line of sight obstacles.
**Measured from analog input to analog output, unity gain operation without wireless compression.
Legal Disclaimer & Warranty
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
For the applicable warranty terms and conditions and additional information regarding Music Tribe's Limited Warranty, please see complete details online at musictribe.com/warranty.
FCC Compliance Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Important information: Changes or modifications to the equipment not expressly approved by Music Tribe can void the user's authority to use the equipment.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
Hereby, Music Tribe declares that this product is in compliance with Directive 2014/53/EU, Directive 2014/30/EU, Directive 2014/35/EU, Directive 2011/65/ EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S Address: Ib Spang Olsens Gade 17, DK - 8200 Aarhus N, Denmark
Music Tribe
Music Tribe
