User Manual for HOOKE ROAD models including: BXG.8200-S Earthshaker Front Bumper with Bull Bar and Winch Plate, BXG.8200-S, Earthshaker Front Bumper with Bull Bar and Winch Plate, Bumper with Bull Bar and Winch Plate, Bull Bar and Winch Plate, Bar and Winch Plate, Winch Plate
Hooke Road Earthshaker F150 Front Bumper w/Bull Bar & Winch Plate for Ford F-150 2009 2010 2011 2012 2013 2014 (Exclude Raptor), Full Width Steel Replacement Bumper : Automotive
Hooke Road Bumper Installation Instructions | Installation Manual – Hooke Road 4x4
Hooke Road Bumper Installation Instructions | Installation Manual – Page 2 – Hooke Road 4x4
Front Bumper (1)Contents: BXG.8200-S Accessories Qty Part Name 1 Winch Power Control Box Bracket Picture 2 Nut Plate 2 Connect Bracket Qty Part Name 4 Hex Bolts Bolts Size(mm) M12*35 Picture 10 Hex Bolts M12*30 8 Hex Bolts M8*20 6 Button Head Socket Cap Bolts Screws M8*20 14 Split Lock Washer 12 Split Lock Washer 24 Flat Washer 12 Flat Washer 14 Flange Hex Lock Nuts 10 Hex Nuts D12 D8 M12*30*2 M8*16*1.5 M8 M12 (2)Tools required: A. 19mm Socket Wrench; B. 18mm Wrench; C. 13mm Wrench; D. 5mm HEX Socket Wrench; (3)Installation time: About 1.5 hours, 2-3 people may be needed. Installation time may differ according to your mechanical skill level. (PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!) To view the electronic version (BXG.8200-S), please scan the QR code. (4)Installation instruction: Step 1: Remove the factory bumper. Ready to install this bumper. Step 2: To assemble the wings & the main body. Use the Hex Bolts (M12*30), Split Lock Washer (D12), Flat Washer (M12*30*2), Hex Nuts (M12). Repeat the same installation methods in the other side. Step 3: To install the bull bar into the main body. Use the Hex Bolts (M8*20), Split Lock Washer (D8), Flat Washer (M8*16*1.5), Flange Hex Lock Nuts (M8). Step 4: To assemble the winch power control box bracket & the winch bracket. Use the Button Head Socket Cap Bolts Screws (M8*20), Split Lock Washer (D8), Flat Washer (M8*16*1.5), Flange Hex Lock Nuts (M8). This step isn't 100% necessary. Depends if you have the winch power control box. Step 5: Put the nut plate into the vehicle body. To install the winch bracket into the vehicle body. Use the Hex Bolts (M12*30), Split Lock Washer (D12), Flat Washer (M12*30*2). Step 6: Lift up the bumper and install it into your vehicle. Use the Hex Bolts (M12*35), Split Lock Washer (D12), Flat Washer (M12*30*2), Hex Nuts (M12). Step 7: To connect the bumper and the vehicle with the connect bracket. Use the Button Head Socket Cap Bolts Screws (M8*20), Split Lock Washer (D8), Flat Washer (M8*16*1.5), Flange Hex Lock Nuts (M8). The upper bolts don't need install the flat washer & the split lock washer. Step 8: Keep the bolts loose, raise the bumper, adjust the gap between it and the car, and then tighten up all of bolts after confirming that the desired effect is achieved. Step 9: The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product! Attention: 1.The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product. 2.Please feel free to contact your distributor if you have any kind of question about your purchase.WPS 文字