Osaki OP-Kairos 4D LT Instruction Manual

Contents

1. Safety Precautions
2. Preparation
   • External structure name
   • Internal structure name
   • Mechanical components diagram
   • Mechanical components list
3. Installation
   • Installation 1
   • Installation 2
   • Installation 3
   • Installation 4
   • Installation 5
   • Installation 6
4. The adjustment before massage
5. Massage Operation
   • Built-in remote instructions
   • Tablet remote control operation
   • Voice control use method
6. Operational Instruction and Function Illustration
7. After Massage
   • Restoration of the massage chair
8. Maintenance
   • Clean and maintenance
9. Others
   • Malfunction guide
   • Technical data
   • FCC Compliance Statement

Safety Precautions

Please read this manual carefully before use, and install and use it correctly according to the requirements of the manual.

The safety precautions are to explain the size and severity of the hazard and damage. And divide some situations that may occur due to incorrect use and assumptions into two aspects: [Warning] and [Caution].

Both are important safety warnings, please pay attention to them.

The Meaning of Symbols

• Warning: This symbol is a warning that death or injury may occur.
• Caution: This symbol is a warning of possible injury or damage.
• !: This symbol means that you must follow the instructions.
• ?: This symbol indicates prohibited behavior.
• ?: This symbol means that it is forbidden to disassemble by yourself.
• ?: This symbol indicates the correct operation of the power cord.

Warning

Patients with osteoporosis, spine fractures, and those suffering from acute painful diseases such as sprains or muscle strains.

Heart disease patients (including those who are equipped with a pacemaker or are using other medical electronic equipment) Malignant tumor patients.

People who suffer from perceptual impairment due to diabetes and other high-level peripheral circulatory disorders.

People with abnormal spine or curved spine.

People with herniated disc.

Pregnant women and those who have just finished childbirth, and those who are in poor health.

People suffering from trauma such as thrombosis, acute venous tumor, various skin inflammations, etc.

People who have been found to have lost the ability to discern temperature.

People with high fever symptoms (acute inflammation: such as fatigue, chills, changes in blood pressure, physical weakness)

Seniors over 80

People who are mentally handicapped, mentally handicapped, or incapable of operating this machine are prohibited from using this machine.

People who cannot take care of themselves, infants and drunk persons are prohibited from using this machine.

It is forbidden to use this machine if it gets wet or people with wet body.

People who are not sensitive to heat or those who are allergic to heat must be careful when using it, or do not use it.

Do not fall asleep in this chair.

People with the above symptoms are prohibited from using this machine, or must consult a physician before using this machine. If this product is used, close supervision must be carried out.

Warning: Before sitting, please make sure that there are no foreign objects between the various parts of the machine.

When using the backrest lift, lower leg lift, and lower leg extension, make sure that there are no people or objects around (behind, under, or in front of the chair).

If you experience abnormalities or feel abnormalities during use, stop using it immediately and ask your doctor.

When massaging around the head, pay attention to the movement of the massage head, and don't massage the head too much.

When massaging the surrounding areas of the neck, be especially careful and avoid massaging the neck too heavily.

Do not use this machine to massage your abdomen or knees.

If you want to leave the seat during the massage, you must stop the operation of the massage chair before leaving the seat.

Do not use it with other equipment at the same time.

Do not let children or pets play on or around the machine (especially when in use); also do not sit or stand on the backrest, armrests, or legs.

When used by people with limited mobility or lack of communication skills, strict and continuous care must be provided.

Before moving the machine, the angle of the backrest and legs must be adjusted back to the original state.

This product contains magnets. Keep a certain distance if you have implanted electronic medical devices, such as pacemakers, or if you have credit cards, data storage media, mechanical watches, or similar items on your person.

When using the product for waist heating, make sure to position it on the sides (the outer edge of the seat), avoiding the massage area to prevent damage to the internal heating element.

After each massage session, please make sure to fold and store the heated shawl on the sides of the back to prevent damage to the internal heating element.

To remove a shawl or flip it upwards, it is necessary to unplug the connector to avoid damaging the wires.

When using a heated shawl, the left and right sides should not be stacked together.

When installing this machine, please turn off the power switch and unplug the power plug after the chair is reset.

Only connect the plug of this machine to a suitable power outlet. And be sure to fully insert the plug into the power socket to reduce the risk of short circuit or fire.

When not in use, be sure to unplug the power plug of the machine.

Before unplugging the power plug, turn off all massage actions and switches.

Caution

This product is intended for use by individuals weighing below 270lbs.

Please use it on a flat ground.

When used by overweight individuals, the product may generate significant noise during operation, and the fabric may wear out more quickly.

To prevent it from accidental dumping.

Please start with a light massage. The recommended use time is 20 minutes, and the same position massage within 5 minutes.

Long time continuous use will have an adverse effect.

Please confirm the correct position of the massage head before sitting down slowly.

To avoid accidental damage.

The tablet hand controller should be placed on the tablet support in time, and do not randomly place it to avoid damage to the tablet hand controller from being squeezed or dropped.

Before connecting the power plug to the socket, be sure to check that the power switch is in the off position.

It is forbidden to curl and store the cushions and other accessories of the massage chair.

It is forbidden to run the machine without load for a long time.

It is forbidden to leave the appliance unattended after plugging in the power source.

Do not use it when the power plug or socket is loosely inserted. To prevent electric shock and short circuit.

Do not use a power supply other than the rated voltage to avoid fire, electric shock or malfunction.

The power cord must not be broken, reworked, twisted, stretched, knotted, or pressed with heavy objects (pay special attention not to be pressed under the machine), etc.

If the power cord or plug is damaged, cannot work normally, please do not use this product.

Keep the power cord away from heat sources.

If the machine is not working properly, has been dropped or damaged, has been splashed or dropped into the water, it must be repaired by professionals or sent to the designated repair center. Do not modify, disassemble and repair by yourself.

If the power cord is damaged, you must use a special power cord or buy special components from its manufacturer or maintenance department to replace it.

To avoid electric shock or personal injury, please do not open or disassemble any parts of this machine without authorization. There are no user-serviceable parts in this machine.

Before use, please lift the back cushion to check whether the fabric of the backrest and other parts is damaged. If there is any damage (no matter how small the damage), please stop using it in time and unplug the power socket. Request for a repair.

When not in use, before unplugging the power plug, turn off all massage actions and switches.

Be sure to insert the power plug completely into the power socket.

Check whether the power cord is damaged, there should be no adherents such as moisture or trash on the power plug.

For safety, please install the ground wire accurately. The power plug must be plugged into a socket with a grounding wire. The ground plug cannot be bent or removed.

Do not press or step on the massage head with hands and feet.

Do not reach between the active massage heads.

Do not put your hands and feet into the gaps of the movable mechanism.

Please do not let objects fall or jam into any slots of the machine.

Do not stand, sit or put anything on the backrest, armrests, or calves.

Do not stand on the machine during use.

Do not unplug the power plug and turn off the power switch during use.

Do not put your hands and head into or under the calf massage area.

Do not use hard hair accessories on the head.

When massaging the buttocks and thighs, there should be no hard objects in the trouser pockets.

Do not hit the armrest with hard objects or sharp cones, so as not to affect the appearance of the armrest.

When the backrest of the massage chair is in an inclined position, do not sit on it or press it heavily.

Do not use it when the skin is bare or wearing only thin clothes. Although thin clothes can enhance the massage effect, it may cause skin irritation and pain or low-temperature burns.

Do not use this product immediately after meals, as it may cause physical discomfort.

Do not use this machine while wearing loose clothes or jewelry.

Keep long hair away from the massager.

Keep this machine away from heat, humidity, sharp objects, and corrosive, flammable and explosive environments.

It is forbidden to put heating items such as electric blankets on the machine.

Do not approach the stove or place it around heating appliances such as heaters.

Do not place it under direct sunlight or in an environment where the room temperature is higher than 104°F.

Do not place it in an environment with severe dust or corrosive gas.

Do not place it in a small space or use in a place with poor air circulation.

Do not use this unit outdoors.

when the power is restored.

To reduce the risk of short circuit and fire.

If you don't pay attention, you may get an electric shock in case of leakage or malfunction.

Keep long hair away from the massager.

Otherwise, the fabric will fade, change color, or harden and deteriorate the synthetic leather.

Caution

Please keep it dry and do not use or store this product in swimming pools, bathrooms and other particularly humid environments.

The chair and the controller can not be sprinkled with water.

Do not use this product when the body is wet.

Be sure to install the ground wire correctly. (Improper grounding connection may cause electric shock hazard. If you have any doubts about the correctness of the grounding of the machine, please entrust a qualified electrician for inspection.)

Please do not use plug adapters. (If the plug attached to the machine does not match your socket, please do not modify the plug, but ask an electrician to install a suitable socket.)

Before cleaning the machine, be sure to unplug the power plug.

After using this machine, be sure to unplug the power plug.

In the event of a power failure, please unplug it immediately.

Please pull out the power plug by holding the plug. Avoid pulling the power cord to unplug the power plug.

After each massage, please turn off the power switch and unplug the power plug.

Unplug the plug immediately when there is a power failure.

Otherwise, it may cause an accident or injury when the power is restored.

Usage environment

Environment temperature: 32°F ~ 95°F Relative humidity: 20%~80%

Storage environment

Environment temperature: 23°F ~ 95°F Relative humidity: 20%~80%

Grounding Instructions

※This machine is equipped with a cable with a grounding plug. The plug must be plugged into a well-installed and grounded socket that meets the requirements of this plug.

Gas pipe: may cause explosion and fire.

Telephone lines and lightning rods: lightning may cause electric shock and fire.

Water pipe: The ground wire does not work where there is plastic in the water pipe.

Replace the Fuse

※When the fuse is blown, please unplug the power plug first, turn off the power switch, then use a screwdriver to open the fuse box cover on the switch box, replace with a new fuse of the same specification, and then reinstall the fuse box cover or entrust an electrician to assist in the replacement.

External Structure Name

External Structure

• Anion
• Right Shoulder Massage Device
• Loudspeaker
• Microphone
• Pillow
• Left Shoulder Massage Device
• Back Seat Cushion
• Tablet Remote
• USB charging port
• Cell phone wireless charging area
• Left Armrest
• LED
• LED atmosphere light
• Castor
• Right Armrest
• Seat airbag
• Seat
• Legrest
• Footrest
• Backrest
• Power Switch
• Power Box
• Fuse Holder
• Power Cord Socket

Internal Structure Name

Internal Structure

• Heating massage roller
• Shoulder Airbag
• Magnet
• Waist Airbag
• Heating shawl
• Hand Airbag
• Seat Side Airbag
• Legrest Heat Cloth
• Leg back roller
• Leg Side Airbag
• Foot Airbag
• Foot Rollers & Shiatsu Points

Mechanical Components Diagram

Mechanical Explosive View

Mechanical Components List

Installation

Installation 1

Step 1 Remove footrest, main body and accessories from the packing box

Hold the left and right sides of the legs and footrest with both hands and lift the legs and footrest out of the seat of the main body.

Take out the accessories box and other parts, and lift out the body of the massage chair by more than two people.

Check and confirm whether the attachments are complete (please check one by one against the packing list).

One person holds the handle of the backrest with both hands, and the other person holds both sides of the lower backrest with both hands and slowly lift it out.

Note: It is forbidden to move this location.

Lift out the left and right armrest, put the armrest flat on the table or the ground. (Be careful not to scratch).

Left armrest

Right armrest

Installation 2

Decide the setting place.

Please make sure you can tilt the space.

Wait at least 20inch away from the wall

At least 0.79inch away from the wall.

Hint: The grounding part of the body, such as cushion, etc. When laying, prepare a mat that can cover the ground part of the body.

Attention:

• Do not use or store the product in swimming pool, bathroom or other particularly humid environment. To prevent leakage, electric shock or failure.
• Please use on a level field. Prevent accidental dumping of the machine.
• Do not close to the stove or placed around the heater and other greenhouse appliances. Can cause fabric fading, discoloration or synthetic leather hardening deterioration, etc.

Installation 3

Step 2 Reset the massage chair

Insert one end of the cable insert to the power box jack, the other end insert to the power socket, turn on the switch on the power box, the massage chair is in powered status. Insert the concave position of the remote plug to the remote cable socket convex position of the left of the seat, insert tightly then twist the nut tightly. Turn on the on/off button of the tablet remote, then turn off, now the backrest is upping and the seat is downing. Put the remote on the seat temporarily after the backrest is reset. After the backrest is reset, please turn off the switch and unplug the power.

Step 3 install the left, right shoulder shell

Put the right shoulder shell close to the chair shoulder outside; Insert the 6 buckle cavities and the 3 buckles of the shoulder shell inside to the 6 buckle joints and 3 buckles of the chair shoulder outside, move the wire harness out from the shoulder shell along the notch on the outside of the shoulder shell at the same time, push the shoulder shell inward hard to make sure the buckle insert firmly. Install the left shoulder shell in same way (there is no wire harness).

Right shoulder shell

Inside of the right shoulder shell

Chair shoulder outside

Installation 4

Step 4 Install left and right armrest

Twist down the two M6*20 screws on the front end of the iron frame on both sides of the seat. Put the right armrest close to the side of the main machine, insert the side wire harness of the chair shoulder to the wire harness socket of the chair shoulder side. Insert the fixed-axis on the end of the armrest to the card slot pallet on the up of the shoulder side. Insert the stop block into the fixed hole on the up of the shoulder. Insert the fastenings on the bottom of the armrest to the card slot pallet on the side of the seat frame; Insert firmly the air tube of the armrest to the seat air tap, and insert firmly the wire harness. Aim the fixed panel on the side of the armrest to the fixed shelf hole on the side of the seat frame, then use an Allen wrench to screw in a M6*20 screw to tighten. Install the left armrest follow the above steps, there is no wire harness on the left armrest.

Note: Do not squeeze the air tube during installation, otherwise it will lead to air leakage or the air bag will not inflate. Make sure the connection of the fixing plate and wiring harness is firm, otherwise the armrest will fall off or the convenient hand controller, speaker and Bluetooth will not work.

Wire harness socket

Card slot pallet

Wire harness

Fixed panel

Air tube and wire harness

Right armrest

Installation 5

Step 5 Install the legs and footrest.

Screw down the legs and footrest hanging ears; Plug the wire harness into the socket; Connect the air tube of leg-rest with the air nozzle of the main machine firmly; Lift the upper rotating shaft press plate of the hanging lug, lift the legs and footrest, put the rotating shaft into the main engine hanging lug, and put the rotating shaft press plate down; Tighten the screw.

Note: When connecting the air pipe and the wire harness, the air pipe and the wire harness should not be wound together.

Hanging ears

Rotating shaft

Shaft

Socket Air nozzle

Harness plug

Air tube

Step 6 Install the bracket of the tablet hand controller

Insert the plate bracket rod into the bracket seat of the left armrest. Insert it according to the shape of the bracket and the shape of the seat hole until the bottom screw of the bracket is stuck in place; Put the tablet controller into the bracket;

Bracket seat

Bracket

Left armrest

Step 7 Connect the air pipe with the heating wire and install the back seat cushion

Connect the seat part and the air tube of the waist airbag; connect the waist heating wire; finally connect the back cushion zipper together.

Warm Suggestion: When the people sits on the chair, the bottom of the pillow is level with the ear, and then the pillow is connected with the back of the back. This shape detection will be more accurate, to achieve a comfortable massage effect.

Seat and back seat cushion connect heat cord.

When installing the back seat cushion, we should pay attention to: the middle leather position of the back cushion is aligned with the middle position of the chair backrest.

Two air pipes and two air nozzles on the upper end of the back seat cushion are connected.

The back seat cushion is connected with the back seat cushion and the two sides of the back seat through a zipper.

The back seat cushion is connected with seat front side with a zipper.

Connect the velcro between leg rest and seat front side.

Zip back seat cushion front side with legrest.

Installation 6

Step 8 Operation after installation

1. Plug the power plug into the power box socket under the backrest.
2. Insert another power plug from the power cord into the power socket.
3. Turn on the power switch at the back of the power box.
4. (Power switch "O/I", press I to connect.)

Use the handy hand controller on the armrest or the tablet hand controller to choose the massage function, enjoy this product to bring you relaxed and comfortable massage.

Before connecting the power plug to the socket, be sure to check that the power switch is in the off position.

The adjustment before massage

Environment

Caution

• Don't use the chair in wet places like near swimming pool, bath room to avoid leakage or electric shock.
• Don't use under sunlight or near stove or other heating place to avoid upholstery deteriorated.
• Please use chair in flat place to avoid chair falling or noise or other unexpected trouble.

Check environment

Space size for using the chair

• Zero space from wall. Tips: at least 0.79inch from wall.
• At least 20inch in front of the leg.

Check places in front

Check the areas when back and leg extending, make sure no people, pets or other things around.

Check surroundings

When the backrest or legrest reclines or extends, please pay attention to:

1. Check any person or things in every direction.
2. Check the space size.

Check power cable, plug

1. Clean the dust on plug on time. (using dry cloth).
2. No damage, re-do, bend, stretch, tie or press with heavy thing (especially can't be pressed by the chair) on power cable.

Massage Operation

How to move massage chair

Caution

Don't move chair when it's working in case of accidents or damage.

How to move

• Bind the cables and put them in the seat to avoid damage when moving.
• If you plump the chair, it may damage the inner parts of the chair.
• Don't use the castor if the floor is wooden or other easy damaged material. It will need 2 or more persons to lift the chair.
• Make sure the power is off and the plug doesn't touch the floor (It's better to let the chair in standing status to avoid the back crashing the floor).

Normally

Press down the head part to make the gravity fall on the back castors. Then push the chair to desired destination steadily and set it down slowly.

Rolling Wheel

Please hold the footrest to move the chair as shown in the picture in case any scratches on the leatherette.

During massage chair backrest lie down process, can't move the armrest.

Because the chair is heavy, it may ruin your floor in long time setting. Please put a blanket or other soft things to protect your floor.

Adjustment before massage

Before adjustment

Please confirm the position of the massage head before sitting down slowly.

Avoid injury caused by improper position of massage head.

Acupoint pulse tracking detection and confirmation

When detecting the position of acupoint pulse, if the massage head cannot detect it, the shoulder should be in the middle position by default.

Proper posture: please put your back against the back of the chair and lean your head back on the pillow cushion.

When the position of acupoint pulse is automatically measured, the hand controller will prompt.

When the prompt of "adjustment of shoulder height position" appears on the hand controller, if the shoulder height needs to be adjusted, the shoulder height can be adjusted according to the up and down arrows on the interface.

Avoid massage head on your acupoint pulse position detection is not accurate, affect the comfort of massage.

Kind suggestion

When you feel the massage strength is not enough, please remove the pillow and shoulder pads, and then massage.

Built-in Remote Instructions

Backrest Up & Leg-rest Down

Leg-rest Up & Backrest Down

Leg and foot Up

Auto Program

Zero-Gravity

Power Switch

Leg and foot Down

Speed

Emergency Stop

Tablet remote control operation

Tips: When the following functions are enabled, the tablet hand controller will display the status synchronously.

1. In the standby state, press the power on key for about 3 seconds, and the massage chair will enter the boot state; In the boot state, When the massage chair needs to be turned off, press the power switch for about 3 seconds to reset the massage chair. If you're in an emergency stop In the state, click the power switch to turn off the massage chair when confirming that there is no danger.

2. When the device is turned on, pressing this button repeatedly will cycle through four angles: zero gravity, leisure, sleep, and reset. During the operation of the angles other than the reset, the button will appear blue.

3. Press this button to stop the current operation and the power indicator and emergency stop indicator blink in the boot state; Press the power button to shut down, other keys are invalid.

4. In manual operation mode, after shoulder height detection, pressing this button allows you to adjust the movement speed of the device. There are a total of 5 speed levels that can be adjusted. The tablet handheld controller interface will display corresponding speed level icons.

5. In the powered-on state, after shoulder height detection, each press of the auto button will switch to a different automatic program. The corresponding indicator light will illuminate, and the tablet handheld controller screen will display the corresponding information. There are a total of five automatic massage programs: Chinese massage, Pain Relief, Stretch, Senior, Quick Demo.

6. in the boot state, press and hold this button, little legs up. Release the button, leg stops running, Angle It's locked in this position.

7. in the boot state, press and hold this button, small leg down. Release the button, leg stops running, Angle It's locked in this position.

8. Hold this key, backrest goes up and leg-rest goes down; release this key, backrest and leg-rest stops moving.

9. Hold this key, back-rest goes down and leg-rest goes up; release this key, backrest and leg-rest stops moving.

Top surface of tablet remote control

ON/OFF buttom

Tablet Remote Control

1. After the chair is powered on, the tablet is turned on by default and the boot interface is displayed. Wait a while to enter the main interface, and press the power switch on the top right of the tablet hand controller to turn on/off the tablet hand controller display.

Main Interface 1

AI MASSAGE ROBOT

Quick Demo

Chinese Massage

Stretch

Pain Relief

Senior

On/Off

Quick Demo Chinese Massage Stretch Pain Relief Senior

Navigation Icons, Slide left and right to switch the main interface.

Position Adjustment Interface

Legrest up

Zero Gravity

Legrest retract

Leisure

Legrest down

Legrest extend

Back rest

Backrest

Additional function interface

4D adjust key

Foot roller adjustment diagram

Air pressure adjustment diagram

Posture adjustment button

0

2

5

4D

3

Foot Roller Pressure Strength

Restore stop key

On/Off

Pause

◄ 05:59

Time adjustment

Gluteus Maximus Strain easy to cause sciatic nerve pain, lower limb numbness, X/O leg

Back

Roller

Lower Back or Chest

Side

Knees

Pose Heat

Additionals

“Home page” press this button, return to the home page.

Voice Command button, clicking this button, get into the "Voice Command" interface.

Additional function icon

Heating button

"Favorite button", When you click this "favorite button," a bookmark dialog box will pop up, and upon clicking "OK," the item will be successfully bookmarked.

AI MASSAGE ROBOT

Quick Demo

Anion button

Foot Roller

Pose Heat

Additionals

Additional function interface

AI MASSAGE ROBOT

Quick Demo

5

4D

3

Pressure Strength

Anion Restore

Back rest upward

Sleep

Backrest downward

Reset

◄ 05:02

Gluteus Maximus Strain easy to cause sciatic nerve pain, lower limb numbness, X/O leg

Pose Heat

Additionals

“Pause” button, press it and it will light up, then all the massage functions will stop, the interface only have Start and On button can be used, press start button to make the massage functions begin to work normally.

“On and Off” button, press it then the icon light up, and turn ON the massage chair can be used.

Foot roller adjustment icon, two levels in total. Click the bar-shaped button icon to adjust.

4D adjustment button, five levels in total. Click the circular button icon to adjust.

Time display and adjustment button: It displays the remaining time for the current function. The left and right arrows can increase or decrease the time. The following section shows the acupoint muscle massage effects.

Heating button: Click to open the heat therapy settings window, where you can turn on or off the heating function for the massage mechanism, waist or chest, and knee areas. There are two levels of temperature adjustment. If you select 2 levels of heating for the massage mechanism, a warning window will pop up. Click 'OK' to enable the heating function or click 'Cancel' to disable it.

Air pressure adjustment icon, five levels in total. Click the circular button icon to adjust. The minimum air pressure can be set to level 1.

Position adjustment button, click and enter the position adjustment interface.

Additional function icon: Click to open the additional function settings window.

The massage of the human body's acupoints and muscles.

4D Plus(Minus)

Zero gravity

Voice command interface

AI MASSAGE ROBOT

Voice Command

Continue massage

Position reset

Chinese massage

Volume up(down)

Strong (Weak)air

Stop massage

Pause massage

Quick demo

Relax mode

Vitality mode

Stretch mode

Morning mode

Pain Relief mode

Midday mode

Senior mode

Night mode

A new technique

Hello Kiri... Neck Shoulder mode

Back waist mode

Glutes mode

Yoga mode

Legrest Up(Down)

Change a new mode

Leg extension(retraction)

(Switch off) foot rollers

(Switch off) heat function

Backrest Up(Down)

(Switch off) air pressure massage

Emergency stop

Sports recovery mode Spine Care mode

Waist Glutes mode

Switch off voice function

Boss mode

Lady mode

Leg and Foot mode

Additional function settings window

Restore

Operational Instruction and Function Illustration

On/Off

When turned on, clicking this button enables you to open or disable the touch sound and voice function. The voice switch is set to "ON" by default when the device is powered on.

Body scanning interface

Body scanning finished, enter into manual shoulder height position adjustment interface.

Body shape detecting

Please adjust your sitting position. Lean back closely to the backrest of the chair. Put your head to the pillow, adjust to the deepest area of the chair.

Detecting, please wait......

Manual shoulder height adjust

Shoulder height adjustment

Shoulder height detecting automatically is completed, slightly adjust the height per your actual need.

Program Interface Switching

1. When there is a program running, you can return to the main interface and click on the icon of the currently running program to return to the running interface.

2. If there is no user input on any interface for more than 15 seconds, it will automatically switch back to the running interface. If there is no program running, it will switch to the main page.

3. In the running interface, clicking on the title allows you to return to the main page or the settings page.

Voice control use method

The use of smart voice control (has voice control function)

In the standby mode, press the power button on the tablet handheld controller or the convenient handheld controller to enter the powered-on state. At this time, the voice recognition system enters the waiting state.

To use the voice recognition function, you need to say "Hello, Kiri" for the system to recognize the subsequent voice commands. Once the voice mode is activated, if the massage chair is turned off, you need to press the power button again to restart the voice function.

Please use standard Mandarin to speak the following voice commands. If they are not recognized, please pause for 2 seconds and raise the volume to speak again.

When the massage chair recognizes a command, there will be corresponding voice feedback from the speaker, indicating successful command recognition. The voice function is enabled by default every time the device is powered on. Please speak the voice commands clearly and loudly. If not recognized, pause for 2 seconds, raise the volume, and try again.

Voice command entry:

Voice control

Hello, KIRI

Hello, KIRI, Stop massage

Hello, KIRI, Change a new mode

Hello, KIRI, Quick demo

Hello, KIRI, Chinese massage

Hello, KIRI, Pain Relief mode

Hello, KIRI, Stretch mode

Hello, KIRI, Neck Shoulder mode

Hello, KIRI, Glutes mode

Hello, KIRI, Back waist mode

Hello, KIRI, Sports recovery mode

Hello, KIRI, Senior Mode

Hello, KIRI, Relax mode

Hello, KIRI, Vitality mode

Hello, KIRI, Yoga mode

Hello, KIRI, Spine Care mode

Voice control use method

Voice control use method

Voice command entry:

Voice control

Hello, KIRI, Morning mode

Hello, KIRI, Midday mode

Hello, KIRI, Night mode

Hello, KIRI, Boss mode

Hello, KIRI, Lady mode

Hello, KIRI, Waist Glutes mode

Hello, KIRI, Leg and Foot mode

Hello, KIRI, A new technique

Hello, KIRI, Full body massage

Hello, KIRI, Partial massage

Hello, KIRI, Point massage

Hello, KIRI, Rollers up

Hello, KIRI, Rollers down

Hello, KIRI, Make it narrower

Hello, KIRI, Make it wider

Hello, KIRI, Air pressure massage

Hello, KIRI, Switch off air pressure massage

Hello, KIRI, Backrest Up

Hello, KIRI, Backrest Down

Hello, KIRI, Legrest Up

Hello, KIRI, Legrest Down

Hello, KIRI, Leg extension

Hello, KIRI, Leg retraction

Hello, KIRI, Speed up

Hello, KIRI, Slow down

Hello, KIRI, 3D Plus/4D Plus

Hello, KIRI, 3D Minus/4D Minus

Hello, KIRI, Strong air

Hello, KIRI, Weak air

Hello, KIRI, Zero gravity

Hello, KIRI, Position reset

Hello, KIRI, Foot rollers

Hello, KIRI, Switch off foot rollers

Hello, KIRI, Heat function

Hello, KIRI, Switch off heat function

Hello, KIRI, Anion function

Hello, KIRI, Switch off anion function

Hello, KIRI, Pause massage

Hello, KIRI, Continue massage

Hello, KIRI, Emergency stop

Hello, KIRI, Switch off voice function

Operation instruction and function illustration

Bluetooth

Step1.Power on

Operate the massage chair according to the method in the previous section.

Step2.Connect Bluetooth

Search for Bluetooth and connect with mobile phone, tablet, etc

Step3.Play music using Bluetooth

Wireless Charging

Step1.Power on

Operate the massage chair according to the method in the previous section.

Step2.Charging

Place your phone on the wireless charger, make sure that the phone is well located at the charging area of wireless charger.

Attention:

1. Please keep the charger away from water or other liquid.
2. If you need to clean the charger, please make sure the massage chair is not connect socket.

Operational Instruction and Function Illustration

On/Off

Step 1. Turn on the power

1. Make sure the A hole is inserted into the power plug at one end of the power cord.
2. Insert the power plug into the socket.
3. Turn on the power switch of power box, massage chair powers on.
4. Press "ON/OFF" button of the panel remote or quick keys, massage chair is ready to work, could be operated after reminding interface disappear.

Built-in Remote

Tablet

Step 2. Massage

1. According to the operating instructions of the tablet remote, select the corresponding function massage. For massage techniques detail, please refer to the instructions for using the tablet remote.

After the massage is over, the massager is reset, and the tablet remote show it is shutting down.

Warning

①Please lift up the pillow cushion and back cushion before use them, to confirm whether the fabric of the backrest part and other parts are damaged. If there is any damage (no matter how small the damage), please stop using it in time, unplug the power socket, and perform entrusted maintenance.

②Only connect the machine plug to a suitable power outlet.

Step 3. Turn off the power

1. In the shutdown state, press the tablet remote panel button again to turn off the machine, and the machine will automatically store it.
2. After the storage is finished, turn off the power switch on the power box under the backrest.
3. Finally, unplug the power plug from the socket.

Before sitting down, make sure that there are no foreign objects caught in the machine (including the armrest, legs and feet, backrest and seat, etc.).

②The feet are equipped with safety protection devices, when there is a foreign body between the legs and feet, the feet automatically stop retracting.

Make sure that the massager is in the storage place then sit down.

Please do not stand on the machine during use it.

Watching The power box upper cover is equipped with a safety anti-pinch device. When there is a squeeze between the power box and the back cover or there is a heavy object on the power box upper shell, the backrest will stop lifting.

Function Illustration

Legrest Up

Press this button on controller, legrest goes up. Release the button, legrest stops moving, the angle is locked in this Position.

Legrest Down

Press this button on controller, legrest goes down. Release the button, legrest stops moving, the angle is locked in this position.

Legrest up and backrest down

Press this button on controller, backrest goes down and legrest goes up. Release this button, backrest and legrest stops moving, the angle, is locked in this position.

Backrest up and Legrest down

Press this button on controller, backrest goes up and legrest goes down. Release this button backrest and legrest stops moving, the angle, is locked in this position.

Legrest extend and retract

When legrest get up to an certain angle above the ground, its length can be adjusted into a suitable one by extending and retracting within 19cm automactically.

Zero-gravity

By pressing the " ☯ " button on the handheld controller, you can adjust the massage chair's position to achieve a comfortable zero-gravity state. Pressing this button continuously will cycle through four angles: zero gravity, leisure, sleep, and reset. The tablet handheld controller interface will display corresponding zero-gravity icons. This zero-gravity position can effectively relieve pressure on the spine and joints, providing a more relaxing and comfortable experience for the user.

Tips:

Zero gravity is based on the NASA space capsule relaxation principle, through the three-part multi-angle change combination of the back, seat, and legs, and make the legs raised and the seat sunk, so that the elevation angle between the body and the legs is 128 degrees (+/-7 degrees), keeps the heart and knees in the same horizontal level, the blood circulation pressure is reduced, and the body pressure is moved into the buttocks. At the same time, due to the zero gravity angle design, the touching area of the human body and the massage chair is increased, so that the pressure on each part of the body is evenly distributed to the massage chair, reducing the pressure on the heart and spine, and realizing a comfortable massage experience, creating a completely relaxing, natural and comfortable massage posture.

1. Please make sure there is no people, no pets or any stuff around the backrest to avoid unexpected hurt or property loss.

2. When adjusting the backrest, be careful of the gap between the backrest and armrest.

3. When the legrest is moving, please do not stand on or leave from the seat, do not stop the legrest from moving in case of causing damage to the chair.

After Massage

Restoration of the massage chair

1. Confirm whether there are people, pets or other items in the movement range of this chair's backrest or leg-rest.
2. Turn off the power switch.
3. Unplug the power plug from the power socket. (Attention: hold the right plug position)
4. Do proper tidies and cleaning.

Attention:

1. After the massage, press the "on/off" button to turn off all the massage movements and wait for the massage rollers to be collected and put in place.
2. After use, make sure the power supply is disconnected to avoid mischievous. Accidental injury to children or other pets.
3. After use, turn off the power switch, pull out the power cord plug, Environmental protection and energy saving.
4. Avoid pulling the power plug by pulling the power cord alone.
5. Avoid damage caused by moisture, dust and degradation of insulation.
6. After each massage session, please make sure to fold and store the heated shawl on the sides of the back to prevent damage to the internal heating element.

Function Illustration

Arm Massage

The armrest has built-in pulse pressure massage function to realize the pinching of the arm and the finger pressure of the palm acupoints, improve the blood circulation and relieve the numbness of the hand.

Calf rubbing Function

The innovative calf rubbing technology provides kneading and rubbing in leg position, combined with calf rolling, heating and pulse air squeezing, the leg muscles will be massaged sufficiently to prompt the blood circulation, and effectively relieve the leg aches and restore the energy on the muscles.

Shoulder Massage

Multi-layer extrusion airbags is deployed on both sides of the shoulder, Achieve pressure shoulder stretch massage, relieve shoulder fatigue.

Foot Safety Anti-Clip Function

When the footrest angle is being adjusted, the massage chair can automatically detect the length of human legs, do not put your feet on the out cover if footrest now, otherwise it will affect the detection of the leg length, resulting in retraction failure of the footrest. Also, there is anti-pinch reminding on auto program interface of tablet controller.

There are 3 places in the foot anti-clip induction area

When the massage chair is turned off, do not put your feet or any parts on your feet face, or the foot retracts to stop; In this state the chair continues reset, the legs and feet can not be collected to the original position.

Note: When the power is turned on, the massage chair should be fully reset. Turn on the machine again, otherwise it will cause the anti-clamping function to fail.

The power box have the flowing anti-pinch function, if there is heavy obstacle pressed the cover of power box, the backrest will stop declining, and continue to decline after heavy obstacle removed.

Heating function

Chinese heat therapy is applied to the neck, shoulders, lower back, hips, and knees, promoting blood circulation in the body and achieving the effects of strengthening the body, maintaining health, and prolonging life.

Foot Roller Massage

Footrest parts with roller massage and air pressure massage function, Through stimulating the foot reflex zones, and clear the body meridians, human organs function.improve the body resistance and immunity effectively.

Clean and Maintenance

Synthetic leather

General cleaning

Clean with tidy, soft and dry cloth slightly.

(Chemical or medical cleaning products are forbidden)

If leather is dirty

1. Dip soft cloth into 3-5% neutral detergent solution, squeeze it then clean the stain on the surface gently.
2. Wash cloth, squeeze it and wipe with detergent.
3. Clean it softly with dry cloth.
4. Allow to dry (air blower is prohibited)

Plastic parts

1. Dip cloth into neutral detergent, squeeze it and clean.
2. Wipe with water-dipped but squeezed cloth.
3. Allow to dry.

Clean the controller

1. Wipe with soft cloth after squeezing.
2. Allow to dry.

Propellant, diluent or alcohol are prohibited.

Cloth material

1. Dip cloth into weak neutral detergent, squeeze it and clean the material surface.
2. (Diluent, gas, alcohol are prohibited)
3. Brush the dirty parts with weak neutral detergent. (avoid excessive brushing)
4. Excessive cleaning may cause damage to cloth material.
5. Wipe with water-dipped but squeezed cloth.
6. Allow to dry.

About cleaning

• Before cleaning, unplug the electricity, don't touch plug with wet hands.
• Make sure hands are dry when plugging to the socket.
• If failed to follow the mentioned instruction, user may get electric shock or burned.

Malfunction guide

FAQ and Troubleshooting

Note: If the troubles are not caused by above reasons, please turn off the power switch and cut off the power, then contact the manufacturer or service agent to repair your chair.

Technical data

The product is massage chair, it was designed for indoor.

Recommended working time: 20 minutes.

And the same position massage within 5 minutes.

Frequency band(s) of operation : 100-300KHz, 2400-2483.5MHz

Operating frequency: 110-205KHz, 2402-2480MHz

Channel spacing/bandwidth: 2MHz for Bluetooth

RF output power: Wireless charging: 34.06 dBuA/m at 3m Bluetooth: -0.18dBm (Max. e.i.r.p.)

Type of antenna: Induction coil, Chip antenna

Ambient Temperature: 41°F ~ 77°F

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received including interference that may cause undesired operation.

Contain FCC ID:

Wireless Charging:2A78H-KT10W24V

Bluetooth: 2AOC9-ZENBDM10A