Tyger Auto: Contact Us
Installation Guide for TYGER models including: TG-AS2T24003 D P, TG-AS2T24003, TG-AS2T24003 Access Fit, TG-AS2T24003, Access Fit, Fit
File Info : application/pdf, 4 Pages, 3.11MB
DocumentDocumentTYGER ACCESS TG-AS2T24003 Scan to Download the Latest Digital Version BEFORE INSTALLATION READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT TORQUE VALUES Fastener Size Class 8.8 Torque (ft-lbs) 6mm 6-7 8mm 15-16 10mm 31-32 12mm 54-55 14mm 87-88 Class 10.9 Torque (ft-lbs) 6-7 22-23 44-45 78-79 125-126 x1 Driver/Left Tyger Access x1 Passenger/Right Tyger Access x1 Driver/Left Front Mounting Bracket [A] x2 Driver/Left Center & Rear Mounting Brackets [B] x1 Passenger/Right Front Mounting Bracket [C] x2 Passenger/Right Center & Rear Mounting Brackets [D] x12 8-1.25 x 25mm Hex Combo Bolts x12 8mm Lock Washers x12 8mmx24mmx2mm Flat Washers x12 8-1.25mm x 30mm Hex Bolts Top View ATTENTION: Refer to D and P labelling on the side of the tubes to determine Driver and Passenger TYGER Access P Passenger Side TYGER Access Front x1 [A] Driver/Left Front Mounting Bracket D Driver Side TYGER Access x2 [B] Driver/Left Center & Rear Mounting Brackets x1 [C] Passenger/Right Front Mounting Bracket x2 [D] Passenger/Right Center & Rear Mounting Brackets x12 8mm Lock Washers x12 8-1.25mm x 30mm Hex Bolts x12 8mm x 24mm x 2mm Flat Washers x12 8-1.25mm x 25mm Hex Combo Bolts 1/4 Customer Support: www.tygerauto.com/contact V241203 TYGER ACCESS Reference the letters printed on the brackets to determine mounting locations Top View D Driver Side TYGER Access [A] [B] [B] Front [D] [D] [C] P Passenger Side TYGER Access Bottom View D Driver Side TYGER Access [B] [B] [A] Front Front Front [C] [D] [D] P Passenger Side TYGER Access 2/4 TOOLS REQUIRED Ratchet 13mm Socket Extensions Wrench STEP 1 MOUNTING BRACKETS Follow (Fig 1 6) to install the mounting brackets to the Passenger/Right Side. Hand tighten hardware only at this point. TYGER ACCESS (1) 8-1.25mm x 30mm Hex Bolt (1) 8mm Lock Washer (1) 8mm x 24mm x 2mm Flat Washer C (Fig 2) Attach Passenger/Right Front Mounting Bracket as shown [C] (Fig 3) Attached Passenger/Right Front Mounting Bracket [C] Passenger-side Front Mounting Area Front Passenger-side Center & Rear Mounting Area (Fig 1) Attach Passenger/Right Front Mounting Bracket to front mounting location shown using the threaded inserts (Fig 4) Attach Passenger/Right Center/Rear Mounting Bracket to Passenger/Right Center mounting location using the threaded inserts 3/4 TYGER ACCESS (1) 8-1.25mm x 30mm Hex Bolt (1) 8mm Lock Washer (1) 8mm x 24mm x 2mm Flat Washer D Front STEP 3 DRIVER SIDE Repeat STEPS 1-2 for driver side installation. Use Front Mounting Bracket [A] instead of [C]; Use Center & Rear Mounting Brackets [B] instead of [D]. (Fig 5) Attach Passenger/Right Center/Rear Mounting Bracket as shown [D] D (Fig 6) Attached Passenger/Right Center/Rear Mounting Bracket [D] to Vehicle. STEP 2 MOUNTING RUNNING BOARD Follow (Fig 7) to install the Tyger Access Drop Step on the Passenger/Right Mounting Brackets. Ensure all hardware is hand tightened at this point. (2) 8mm Combo Bolts STEP 4 Ensure Tyger Access Drop Step is level and straightened, then tighten all fasteners. Installation is complete. Perform periodic inspections to the installation to make sure that all hardware is secure and tight. Complete Installation Front (Fig 7) Attach Passenger/Right Tyger Access Drop Step to Passenger/Right Mounting Brackets, as shown, for all mounting brackets. 4/4