FLIPSKY VX5 Waterproof Remote Controller User Manual
01 Introduction
Thank you for purchasing this product! Improper operation may cause uselessness or even damage. We strongly recommend reading this manual carefully before using this product and strictly following the prescribed operating procedures. FLIPSKY is not responsible for any liability arising from the misuse of this product, including but not limited to liability for direct or indirect loss or damage, and does not assume any liability for unauthorized modifications to the product. FLIPSKY reserves the right to change product design, appearance, performance, and usage requirements without prior notice to the buyer.
VX5 Remote Controller
The VX5 Remote Controller is designed for electric skateboards and surfboards. It features an ergonomic design with several control buttons and a display screen.
- Mode Button: Used for changing modes or settings.
- Horn Button: Activates the horn function.
- Setting Button: Accesses or confirms settings.
- Brake Trigger: Controls braking.
- Power Throttle On/Off Trigger: Controls acceleration and power.
- USB Magnetic Charging Port: For charging the remote.
- 2 Inches Display Screen: Shows various operational data.
Display Screen Icon Introduction
The display screen provides real-time information about the remote and the connected device (e.g., e-skateboard or e-surfboard).
PPM Control Mode (VX5 Remote)
This mode displays the following information:
- Receiver signal quality: Indicates the strength of the signal from the receiver.
- Surfing Mode / Speed Gear: Shows the current operating mode or speed gear.
- Number of GPS Positioning Satellites Time: Displays the count of acquired GPS satellites and current time.
- Remote Battery: Shows the battery level of the remote controller.
- Surfingboard Battery: Displays the battery level of the connected surfing board.
- Throttle: A visual representation of the throttle position.
- Auto-locking Time: Time duration for auto-locking.
- Throttle Progress Bar: Visualizes throttle input.
- Working Record Time: Total operating time recorded.
- Throttle Percentage: Current throttle input as a percentage.
- Realtime Speed: Current speed of the device.
- Speed Unit: Unit of speed measurement (e.g., Km/h).
- ESC.POWER, MOS.TEMP: ESC power consumption and MOSFET temperature.
- BAT.Voltage, MOT.TEMP: Battery voltage and Motor temperature.
- BAT.Current, MOT.Current, Duty: Battery current, Motor current, and Duty cycle.
Note: This mode is applicable to all ESCs and does not feature forward and reverse switching functionality.
E-skateboard Mode (VX5 Remote)
This mode displays similar information tailored for e-skateboards:
- Receiver signal quality
- Eboard Working Mode
- Eboard Battery
- Eboard Mode
- Headlight status (High Speed: Red, Medium Speed: Yellow, Low Speed: Green)
- Number of GPS Positioning Satellites Time
- Remote Battery
- Throttle
- Auto-locking Time
- Throttle Progress Bar
- Working Record Time
- Throttle Percentage
- Realtime Speed
- Speed Unit
- ESC.POWER, MOS.TEMP
- BAT.Voltage, MOT.TEMP
- BAT.Current, MOT.Current, Duty
Note: This mode is applicable to all ESCs and does not feature forward and reverse switching functionality.
02 Wiring Diagram
Detailed connection diagrams are provided for different control modes.
PPM Control Mode (Receiver)
This diagram illustrates the standard PPM connection between the ESC/Motor and the VX5 Receiver.
- Receiver Pins: BAT+, VRX2, VTX2, VRX1, VTX1, GND, 5V, PPM.
- Connections: These pins connect to corresponding ports on the ESC and Battery.
PPM Dual Channel Connection Mode (Receiver)
This diagram shows how to connect the receiver for dual ESC setups.
- Receiver Pins: BAT+, VRX2, VTX2, VRX1, VTX1, GND, 5V, PPM1, PPM2.
- Connections: Connects to two ESCs (ESC1, ESC2) and the Battery.
UART Control Mode (Receiver)
This mode enables advanced control and data display, supporting VESC and FTESC.
- Receiver Pins: BAT+, VRX2, VTX2, VRX1, ESC RX, VTX1, ESC TX, GND, ESC GND, 5V, ESC 5V, PPM.
- Functionality: Supports forward and reverse switching, control, and data display.
VX5 Receiver
The VX5 Receiver is a compact unit that connects to the ESC and motor system.
- Components: LED Signal Light, Antenna.
- Connection Pins: BAT+, VRX2, VTX2, VRX1, VTX1, GND, 5V, PPM1, PPM2. These are typically connected to the ESC and battery.
03 Operation Manual
For detailed operation instructions, please scan the provided QR code. The QR code will direct you to online resources with comprehensive guidance on using the FLIPSKY VX5 remote controller.
