Blaupunkt GTx 1xxx Series 2-Way Coaxial Speakers

Introduction

Proper system planning is vital to maximize the device's performance and road safety. Plan your installation carefully to avoid compromising the performance reliability of the system. Consult an authorized Blaupunkt dealer for installation or reparation. Read the manual carefully before operating the device for the first time.

Safety Notes

Ensure to follow below safety notes during installation and wiring connection:

• Disconnect the negative terminal of the battery. Refer to the safety notes of the vehicle manufacturer.
• Ensure positions of the holes are nowhere near the vehicle component to avoid any damage during drilling.
• Ensure cross section of the cable is no less than 2.5mm² if the positive and negative cables are too long.
• Incorrect installation may result in malfunction of the device or the car sound system.

Installation and Connection Instructions

• Select a dry and well-ventilated location to install the device.
• The device must not be installed in an overly exposed location such as on the rear shelf, rear seat, etc.
• The installation location must be suitable for screw holes and have stable ground support.

Voltage Supply

• Use the supplied power extension cable to connect to the positive battery terminal.
• Firmly and carefully connect the ground lead to a bare metal point on the vehicle chassis.
• The control of the device should be a two-channel control, either via the pre-amplifier output of the car sound system. A control solely via the right or left channel is also possible since the low-frequency portion of the music is generally identical on both channels.

Disclaimer

In no event shall Blaupunkt be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products.

USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on an as-is basis. No warranty, whether expressed or implied, is provided in the U.S. or Canada.

Recycling and Disposal

Do not dispose of your old unit in the household trash! Use the return and collection systems available to dispose of the old device.

This manual may be updated from time to time without any notice.

Specifications

GTx 1352

Pair of 3.5" 2-way coaxial speaker with Polypropylene Cone Composition including mounting hardware.

• Max. Power Handling: 60W
• Normal Output Power (RMS): 20W
• Impedance: 4ohms
• Frequency Response: 120Hz - 20,000Hz
• Sensitivity: 90±3dB
• Mounting Depth: 41mm
• Diameter Hole: 78mm

Diagram Description: Shows a 3.5-inch speaker. Dimensions: Overall diameter 105mm, tweeter height 4.8mm, cutout diameter 70mm, mounting depth 78mm, overall height 41mm, magnet diameter 53mm. Accessories include two 4x32mm screws and two U-clips.

GTx 1402

Pair of 4.0" 2-way coaxial speaker with Polypropylene Cone Composition including mounting hardware.

• Max. Power Handling: 70W
• Normal Output Power (RMS): 22W
• Impedance: 4ohms
• Frequency Response: 100Hz - 20,000Hz
• Sensitivity: 90±3dB
• Mounting Depth: 47mm
• Diameter Hole: 95mm

Diagram Description: Shows a 4.0-inch speaker. Dimensions: Overall diameter 117mm, tweeter height 4.5mm, cutout diameter 70mm, mounting depth 95mm, overall height 47mm, magnet diameter 67mm. Accessories include four 4x32mm screws and four U-clips.

GTx 1662

Pair of 6.5" 2-way coaxial speaker with Polypropylene Cone Composition including mounting hardware.

• Max. Power Handling: 110W
• Normal Output Power (RMS): 33W
• Impedance: 4ohms
• Frequency Response: 70Hz - 20,000Hz
• Sensitivity: 90±3dB
• Mounting Depth: 56mm
• Diameter Hole: 145mm

Diagram Description: Shows a 6.5-inch speaker. Dimensions: Overall diameter 156mm, tweeter height 4.5mm, cutout diameter 80mm, mounting depth 145mm, overall height 56mm, magnet diameter 75mm. Accessories include four 4x32mm screws and four U-clips.

GTx 1692

Pair of 6.0" x 9.0" 2-way coaxial speaker with Polypropylene Cone Composition including mounting hardware.

• Max. Power Handling: 115W
• Normal Output Power (RMS): 35W
• Impedance: 4ohms
• Frequency Response: 60Hz - 20,000Hz
• Sensitivity: 90±3dB
• Mounting Depth: 74mm
• Diameter Hole: 153mm x 220mm

Diagram Description: Shows a 6.0" x 9.0" oval speaker. Dimensions: Overall dimensions 167mm x 119mm, tweeter height 4.5mm, cutout width 80mm, cutout length 220mm, mounting depth 153mm, overall height 74mm, magnet diameter 105mm. Accessories include four 4x32mm screws and four U-clips.

Installation Overview

The installation diagrams illustrate the general process of mounting the speakers into a vehicle's interior panel. This typically involves selecting a suitable location, ensuring proper fit, securing the speaker with the provided screws, and making the necessary wiring connections.

Troubleshooting

If any of the following problems occur, please refer to the possible solutions. Consult a Blaupunkt authorized dealer if problems persist.