Salus SQ610 Quantum Smart Thermostat

User Manual and Installation Guide

Introduction

The SQ610 Quantum is a ZigBee temperature controller for wireless control of iT600 series devices, such as the KL08RF wiring centre, mini TRV head, and RX10RF boiler control module. It can be controlled over the Internet or via the SALUS Smart Home mobile app (ONLINE mode) when installed with the UGE600 Internet gateway (sold separately). The application allows pairing with other system elements like Smart Plug SPE600, Smart Relay SR600, or window/door sensors OS600/SW600. The SQ610 can also operate locally without an Internet connection (OFFLINE mode) using the CO10RF coordinator (sold separately) for device communication, or as a standalone device without any gateway or coordinator.

A full manual in PDF format is available at www.salus-controls.eu.

Product Compliance

This product complies with essential requirements and relevant provisions of Directives 2014/30/EU, 2014/35/EU, 2014/53/EU, and 2011/65/EU. The full text of the EU Declaration of Conformity is available at www.saluslegal.com.

Safety Information

Use in accordance with national and EU regulations. The device is intended for indoor use only and must be kept in dry conditions. Installation must be performed by a qualified person following national and EU regulations. Always disconnect power before cleaning with a dry cloth.

Warning: Ensure the AC 230V mains power is switched OFF before installing or working on any components.

Package Content

Installation Location and Wiring

Thermostat Location

The ideal mounting position is approximately 1.5m from the floor, away from heating or cooling sources, direct sunlight, or drafts. Ensure a minimum clearance of 20cm from doors.

Mounting Instructions

Use the included mounting screws. Remove the back plate from the thermostat, mount the plate to the wall, and then attach the thermostat to the plate.

Wiring Diagram

The thermostat requires AC 230V power supply connected to terminals L (Live) and N (Neutral). It features COM (Common) and NO (Normally Open) terminals for a voltage-free output. Terminals S1 and S2 are for connecting an external temperature sensor or an ON/OFF switch/occupancy sensor.

Symbols Explanation:

LCD Icon Description

The thermostat display shows various icons:

  1. Menu/Settings description + Clock
  2. AM/PM indicator
  3. Temperature unit (°C/°F)
  4. Heating indicator (animates when heating is active)
  5. Cooling indicator (animates when cooling is active)
  6. RF Connection indicator
  7. Internet connection indicator
  8. Occupancy sensor (hotel card) indicator
  9. Key lock function indicator
  10. Standby mode icon
  11. Current Temperature / Setpoint Temperature display
  12. Holiday mode icon
  13. Temporary override mode icon
  14. Settings icon
  15. External / Floor temp sensor indicator
  16. Schedule program number
  17. Schedule mode icon
  18. Day indicator/ SET information
  19. Current Humidity value

Buttons Description

The thermostat features several buttons for control:

Compatibility with Other Salus Controls Devices

The SQ610 Quantum Thermostat supports both ONLINE and OFFLINE modes.

ONLINE Mode

Requires a Universal Gateway connected to the Internet. Allows configuration and use of devices via the SALUS Smart Home mobile app for remote access.

OFFLINE Mode

Operates without an Internet connection for local control. Uses the CO10RF Coordinator as a standard ZigBee coordinator.

Compatible Devices:

Note: SR600 and SPE600 are compatible only with Online Mode.

First Power Up Sequence

  1. Connect the thermostat to the 230V power supply.
  2. The display will show all icons.
  3. The thermostat will then display the software version.
  4. Select your language using the ⬆️ or ⬇️ buttons and confirm with the ✔️ button.
  5. Choose to connect with the network:
    • YES: For ONLINE or OFFLINE mode. Add the thermostat to the Salus Smart Home system via a universal gateway or CO10RF coordinator.
    • NO: For STANDALONE mode. Connect the thermostat directly to devices like pumps, boilers, or receivers without a network system. Network connection can be added later.

Installation in ONLINE Mode

Follow these steps to add your device to the Smart Home app and pair it with other devices:

  1. Connect to the network (YES).
  2. Go to the SALUS Smart Home app on your smartphone or tablet.
  3. Navigate to Home > Equipment > Settings > Setup Equipment.
  4. Scan for equipment.
  5. Connect the equipment.
  6. Once your thermostat is added, name your equipment (e.g., "SQ610 230V Thermostat").
  7. Click on the device name to set it up.
  8. Select the device to pair: UFH Wiring Center or Control Box, Smart Radiator Control, Smart Plug, Smart Relay, or Wired Device.
  9. Click Finish.
  10. The thermostat will display the main screen, indicating successful configuration.

Installation in OFFLINE Mode (Pairing)

Pairing with Wiring Centre / Control Box

  1. Connect to the network (YES).
  2. Open the ZigBee network by pressing the button for 5 seconds.
  3. Select System Type: UNDERFLOOR, then confirm with the ✔️ button.
  4. Use the ⬆️ and ⬇️ buttons to select the Control Box number (refer to the Control Box's PAIR button for its address number) and confirm with ✔️.
  5. Use the ⬆️ or ⬇️ buttons to select the zone number and confirm with ✔️.
  6. The display will show the number of paired TRVs.
  7. Close the ZigBee network by pressing the button for 5 seconds.

Pairing with TRV Radiator Head

  1. Connect to the network (YES).
  2. Open the ZigBee network by pressing the button for 5 seconds.
  3. Select System Type: RADIATORS, then confirm with the ✔️ button.
  4. Now, hold the antenna button for 10 seconds on all TRVs you wish to pair with your thermostat.
  5. The LCD will show the number of paired TRVs. You can pair up to 6 TRVs with one thermostat, provided they are in the same room.
  6. Once all TRVs are paired, press the ✔️ button to finish the pairing process.
  7. Close the ZigBee network by pressing the button for 5 seconds.

Wired Device Connections

The SQ610 Quantum can function as a standalone device without a gateway or coordinator.

1. Wiring Diagram for Volt-Free Connection (e.g., boiler control)

The thermostat's COM and NO terminals are connected to the boiler's control terminals.

2. Wiring Diagram for 230VAC Connections

The thermostat is connected to AC 230V (L, N) and can control a pump or valve actuator (M) via the COM/NO terminals.

3. Wiring Diagram for Control Box Connection

The thermostat connects to a KL08NSB 1-8 Zones control box using L, N, and SL terminals.

Legend:

Boiler connection note: Boiler's contacts for ON/OFF thermostat should be according to the boiler's instructions.

Note: Thermostats without application support can be easily added to the Smart Home app anytime. All settings made before adding are automatically copied.

SQ610 Full Menu Structure

Main Menu

Short Description of Selected Functions

  1. DISPLAY TEMP RESOLUTION: Sets the displayed temperature resolution (0.5°C or 0.1°C).
  2. CONTROL ALGORITHM: Defines room temperature control. Options include ITLC (for Underfloor Heating/Radiators/Electrical Heating), hysteresis (+/-0.5°C or +/-0.25°C), or THB Actuator.
  3. S1/S2 INPUT: Connects a floor sensor, external temperature sensor, or occupancy sensor. Can also be used as a OneTouch rules trigger or Heat/Cool changeover via a NO volt-free contact.
  4. VALVE PROTECTION: Activates actuators weekly for 5 minutes to prevent sticking, especially in summer.
  5. INTERNAL RELAY (COM/NO): Controls internal relay activation/deactivation using COM/NO outputs. Default is enabled.
  6. MIN TURN OFF TIME: Sets the minimum switch-off time to prevent frequent heating/cooling signals.
  7. OPTIMISATION FEATURE: Includes Optimum Start and Optimum Stop functions for energy saving and cost-effectiveness, especially with the ITLC algorithm.
  8. COMFORT WARM FLOOR: Maintains floor warmth even when room heating is not required. Offers 3 levels. This is a comfort feature, not economy, as the heating system may run regardless of room demand.
  9. DEVICE INFORMATION: Displays Software Version, RF range, paired devices, and allows activation of Identification mode.
  10. FACTORY RESET: Resets the device to factory settings. After reset, the device is removed from the ZigBee network and requires re-pairing.

Product Summary & Compatible Devices

Key Features:

Compatible Devices:

Importer:

SALUS Controls Plc, Units 8-10 Northfield Business Park, Forge Way, Parkgate, Rotherham S60 1SD, United Kingdom.

For more information, visit www.salus-controls.com and www.salus-smarthome.com.

Models: SQ610 Smart Thermostat, SQ610, Smart Thermostat, Thermostat

File Info : application/pdf, 16 Pages, 4.93MB

PDF preview unavailable. Download the PDF instead.

SQ610-Wired-Slimline-I-internet-Controlled-Thermostat-Manual

References

Adobe PDF Library 16.0.7 Adobe InDesign 17.2 (Windows)

Related Documents

Preview SALUS VS20WRF/VS20BRF Thermostat - Full User Manual
Comprehensive user manual for the SALUS VS20WRF/VS20BRF thermostat, detailing installation, online/offline operation, ZigBee network compatibility, and troubleshooting for smart home heating and cooling systems.
Preview SALUS Elypso EL600F Smart Thermostat - Quick Start Guide & Installation
A comprehensive guide to installing and operating the SALUS Elypso EL600F smart thermostat within the SALUS Smart Home ecosystem. Learn about its features, compatibility, and setup procedures for optimal home climate control.
Preview SALUS Controls EL600F Smart Home Thermostat Kurzanleitung
Eine prägnante Anleitung zur Installation und Bedienung des SALUS Controls EL600F Smart Home Thermostats, die Funktionen, Kompatibilität, Einrichtung und Bedienung abdeckt.
Preview SALUS HTR-RF(20) Wireless Thermostat Quick Guide and Installation
Quick guide and installation instructions for the SALUS HTR-RF(20) wireless thermostat, designed for underfloor heating. Learn about setup, pairing, LED indications, error codes, and jumper settings.
Preview Salus IT700 Smart Thermostat: Modern Home Temperature Control
Discover the Salus IT700 Smart Thermostat, offering advanced features, WiFi/Zigbee connectivity, and seamless integration for efficient home heating and cooling. Enhance your comfort with smart control.
Preview SALUS RX10RF Wireless Receiver Unit Installation and User Manual
This document provides comprehensive installation, operation, and safety instructions for the SALUS RX10RF Wireless Receiver Unit, designed for use with the iT600 Zigbee system. It covers electrical connections, technical specifications, system integration, and warranty information.
Preview Salus IT700 Thermostat Intelligent : Confort et Efficacité pour la Maison Connectée
Découvrez le thermostat intelligent Salus IT700, une solution moderne et élégante pour le contrôle de la température. Avec sa connectivité WiFi et Zigbee, son design ultra-fin et son intégration facile aux systèmes de maison intelligente (Alexa, Google Home), l'IT700 optimise votre confort et votre efficacité énergétique.
Preview SALUS Controls Produktkatalog: Intelligente Heizungs- und Smart Home Lösungen
Entdecken Sie den SALUS Controls Produktkatalog für innovative Heizungssteuerungen, Thermostate und Smart Home Produkte, die Komfort, Energieeffizienz und ein intelligentes Wohnambiente bieten.