Zigbee 2-Gang In-wall Switch

Important Information

Read all instructions prior to installation.

Function Introduction

• 2-channel switch input for independent control of two loads.
• [Reset Key]: Used for network pairing, TouchLink, and factory reset.
• [LED Indicator]: Off when not added to a Zigbee network; solid on when added.
• 2-channel load output.
• AC power input terminal.

Device Specifications:

Input/Output Voltage: 100-240VAC

Channels: 2

Max Load: Resistive load: max. 5.1A per channel; Capacitive load: max. 1.7A per channel.

Dimensions: 45.5mm x 45mm x 20.3mm

Compatible Load Types

Key Features

• 2-gang Zigbee in-wall switch with Zigbee 3.0 protocol.
• Wide input and output voltage range (100-240VAC).
• Supports both resistive and capacitive loads.
• Independent ON/OFF control for two channels (max 5.1A/CH).
• Input and output terminals use screw connections for safety and reliability.
• Supports multiple Zigbee endpoints.
• Compatible with TouchLink commissioning for direct pairing with Zigbee remotes.
• Can form a Zigbee network without a coordinator and add other devices.
• Supports Find and Bind mode for binding Zigbee remotes.
• Works with Zigbee Green Power switches (up to 20 per device).
• Compatible with universal Zigbee gateway products.
• Can be controlled by universal single-wire push switches (each channel independently).
• Features active power and energy metering.
• Compact mini size for easy installation in standard wall boxes.
• Operates on the 2.4GHz radio frequency.
• IP20 waterproof grade.

Safety & Warnings

• DO NOT install the device while power is applied.
• DO NOT expose the device to moisture.

Zigbee Clusters Supported

Endpoint 0x01 - Channel 1: Basic (0x0000), Identify (0x0003), Groups (0x0004), Scenes (0x0005), On/off (0x0006)

Endpoint 0x02 - Channel 2: Basic (0x0000), Identify (0x0003), Groups (0x0004), Scenes (0x0005), On/off (0x0006)

Endpoint 0x0b - Whole device: Basic (0x0000), Simple Metering (0x0702), Electrical Measurement (0x0b04), Diagnostics (0x0b05), ZLL Commissioning (0x1000), OTA (0x0019)

Operation

1. Ensure wiring is done correctly according to the connection diagrams.
2. This Zigbee device acts as a wireless receiver, controlled by Zigbee signals.
3. Zigbee Network Pairing (with Coordinator or Hub):
   1. If the device is already paired, remove it from the previous Zigbee network first (refer to "Factory Reset Manually").
   2. On your Zigbee Controller or hub, select "add lighting device" and enter pairing mode as instructed.
   3. Reset the device's power to enter network pairing mode. The connected light will flash twice slowly. There is a 15-second timeout; repeat the step if needed.
   4. Upon successful pairing, the connected light will blink 5 times and then stay solid. The device will then appear in your controller's menu for control.

Over Current Protection

If the total load (resistive) exceeds 8.1A, the relay will automatically turn off to protect the device.

Advanced Pairing & Control Methods

4. TouchLink to a Zigbee Remote

Step 1: Initiate TouchLink commissioning. Method 1: Short press the "Reset" button 4 times (or power cycle the device 4 times) for immediate commissioning (180s timeout). Method 2: Power cycle the device. TouchLink starts after 15 seconds if not added to a network (165s timeout), or immediately if already added (180s timeout). Repeat if timeout occurs.

Step 2: Bring the Zigbee remote or touch panel within 10cm of the lighting device.

Step 3: Set the remote or touch panel into TouchLink commissioning mode, following its manual.

Step 4: Successful linking will be indicated on the remote, and the connected light will flash twice.

Notes:

• Direct TouchLink (neither device added to a Zigbee network): 1 remote per device.
• TouchLink after both devices are added to a Zigbee network: up to 30 remotes per device.
• For control via both gateway and remote, add both to the network first, then TouchLink.
• After TouchLink, the device can be controlled by the linked remotes.

5. Remove from a Zigbee Network (via Coordinator or Hub)

Use your Zigbee controller or hub interface to delete or reset the lighting device as instructed. The connected light will blink 3 times to confirm successful removal.

6. Factory Reset Manually

Note: If the device is already at factory default, no indication will appear upon resetting again. All configuration parameters will be reset.

Step 1: Short press the "Reset" key 5 times continuously. Alternatively, power cycle the device 5 times if the "Reset" key is not accessible.

Step 2: The connected light will blink 3 times to indicate a successful reset.

7. Factory Reset via Zigbee Remote (Touch Reset)

Note: Ensure the device is already added to a network, and the remote is added to the same network or not added to any network.

Step 1: Short press the "Reset" button 4 times to start TouchLink commissioning (180s timeout). Repeat if needed.

Step 2: Bring the Zigbee remote or touch panel within 10cm of the lighting device.

Step 3: Set the remote or touch panel into the Touch Reset procedure, following its manual.

Step 4: Successful reset will be indicated on the remote, and the connected light will flash 3 times.

8. Find and Bind Mode

Note: Ensure the device and remote are already added to the same Zigbee network.

Step 1: Short press the "Reset" button 3 times (or power cycle the device 3 times) to start Find and Bind mode. The connected light will flash slowly. This mode has a 180-second timeout; repeat if needed.

Step 2: Set the Zigbee remote or touch panel (target node) into find and bind mode, enabling it to find the initiator. Refer to the remote's manual.

Step 3: The remote or touch panel will indicate successful binding, allowing control of the device.

9. Learn Zigbee Green Power Switch

Step 1: Short press the "Reset" button 4 times (or power cycle the device 4 times) to start Learning to GP switch mode. The connected light will flash twice. This mode has a 180-second timeout; repeat if needed.

Step 2: Set the Zigbee Green Power switch into Learning mode, following its manual.

Step 3: The connected light will flash twice to indicate successful learning. The switch can now control the device.

Note: Each device can learn a maximum of 20 Zigbee Green Power switches.

10. Delete Learning from Zigbee Green Power Switch

Step 1: Short press the "Reset" button 3 times (or power cycle the device 3 times) to start the delete Learning to GP switch mode. The connected light will flash slowly. This mode has a 180-second timeout; repeat if needed.

Step 2: Set the paired Zigbee Green Power switch into Learning mode, following its manual.

Step 3: The connected light will flash 4 times to indicate successful deletion.

11. Setup Zigbee Network & Add Devices (No Coordinator Required)

Step 1: Short press the "Reset" button 4 times (or power cycle the device 4 times) to enable the device to set up a Zigbee network. The connected light will flash twice. This mode has a 180-second timeout; repeat if needed.

Step 2: Set another Zigbee device or remote/touch panel into network pairing mode and pair it to the network, following its manual.

Step 3: Pair additional devices and remotes to the network as desired, following their manuals.

Step 4: Bind the added devices and remotes through TouchLink so they can be controlled by the remotes, following their manuals.

Notes:

• Each added device can link and be controlled by a maximum of 30 remotes.
• Each added remote can link and control a maximum of 30 devices.

12. OTA (Over-The-Air) Updates

The device supports firmware updates via OTA. It will automatically acquire new firmware from the Zigbee controller or hub approximately every 10 minutes.

Wiring Diagrams and Notes

Notes for Diagrams:

• L: Terminal for live lead
• N: Terminal for neutral lead
• S1: Terminal for switch key No. 1
• S2: Terminal for switch key No. 2
• L1: Output terminal No. 1 for light load
• L2: Output terminal No. 2 for light load

Supported Switch Types:

• 1. Push Switch (factory default setting)
• 2. Toggle On/Off Switch (configurable upon request)

Wiring Method 1: External Switches Control through Neutral Lead

1.1. With 1PC 2-Gang 1-Way Switch

Diagram showing the Zigbee 2-Gang In-wall Switch connected to Live (L) and Neutral (N) power. The COM terminals of two external 1-way push switches are connected to S1 and S2 respectively. L1 and L2 terminals are connected to the respective light loads.

1.2. With 2PCS 1-Gang 1-Way Switches

Diagram showing the Zigbee 2-Gang In-wall Switch connected to Live (L) and Neutral (N) power. The COM terminals of two separate 1-gang switches are connected to S1 and S2 respectively. L1 and L2 terminals are connected to the respective light loads.

Wiring Method 2: External Switches Control through Live Lead

2.1. With 1PC 2-Gang 1-Way Switches

Diagram showing the Zigbee 2-Gang In-wall Switch connected to Neutral (N) power. Live (L) power is connected to the COM terminals of the two external 1-way push switches. The other terminals of the external switches are connected to S1 and S2 of the 2-Gang switch. L1 and L2 terminals are connected to the respective light loads.

2.2. With 2PCS 1-Gang 1-Way Switches

Diagram showing the Zigbee 2-Gang In-wall Switch connected to Neutral (N) power. Live (L) power is connected to the COM terminals of two separate 1-gang switches. The other terminals of these switches are connected to S1 and S2 of the 2-Gang switch. L1 and L2 terminals are connected to the respective light loads.

Product Dimensions

Diagram showing the physical dimensions of the Zigbee 2-Gang In-wall Switch, with measurements for width (45mm), height (45.5mm), and depth (20.3mm).