Owner's Manual

Safety Instructions

⚠ READ AND FOLLOW ALL INSTRUCTIONS BEFORE OPERATING FAN. DO NOT USE FAN IF ANY PART IS DAMAGED OR MISSING.

IMPORTANT INSTRUCTIONS

• Use this fan only as described in this manual. Any other use not recommended by the manufacturer may cause electrical shock, fire or injury.
• To reduce the risk of fire or electrical shock, do not expose to water or rain.
• To reduce the risk of fire or electrical shock, do not use with any solid-state speed control device.
• Automatically operated device: To reduce the risk of injury, disconnect from power supply before servicing.
• If the power supply cord is damaged, contact your local service centre or a qualified electrician to install an appropriate replacement cord to prevent any injury or damage.
• This unit is not intended for use in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapor or gas).
• Do not place the fan on a small, not level, uneven or any surface which might allow the fan to tip or fall.
• This unit is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the fan by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the fan.
• This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

GENERAL USE

• Never insert fingers or any other objects through the grille guard when the fan is in operation.
• Do not unplug the fan by pulling the cable cord. Unplug by holding the plug.
• Disconnect the fan from its power source when moving it from one location to another.
• Disconnect the fan from its power source when removing guards for cleaning.
• Be sure the fan is on a stable, flat surface when in operation.
• Do not use the fan in windows. Rain and moisture may create an electrical hazard.
• Do not pour water on the housing or control panel.
• Close supervision is necessary when this fan is used near children, the elderly, and pets.
• Do not place heavy items or sit on the fan.
• Do not place the fan near an open flame, cooking or heating appliance, or hot surface.
• This fan should not be operated outside or exposed to rain.
• Avoid the use of extension cords due to the risk of fire. If an extension cord must be used, the cord must be a minimum of 14AWG and rated not less than 1875W.
• Do not run the power cord under carpeting. Do not cover the cord with throw rugs, runners, or the like. Arrange the cord away from traffic areas where it will not be tipped over.

⚠ WARNING

DO NOT ALTER THE FAN'S ASSEMBLY.

BE SURE THAT BOTH FRONT AND REAR GUARD SCREWS ARE COMPLETELY TIGHTENED IN LOCKING POSITION BEFORE OPERATION.

Shock Hazard: Use the fan only in dry environments. This fan is not intended for use in a bathroom, laundry area, or similar locations, or near sinks, washing machines, swimming pools, or other sources of water. Never locate the fan where it may fall into a bathtub or other water receptacle. Do not use in damp environments such as flooded basements.

Hot Surfaces: Do not touch the fan motor when in use. The motor is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.

Fire Hazard: Fans have arching or sparking parts inside. Do not use near combustible materials or flammable gases or sources of heat. Do not use in areas where gasoline or flammable materials are used or stored. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire, or damage to the fan.

Prevent Electric Shock: This fan has a three-prong grounded plug that must be inserted into a matching properly grounded outlet to reduce the risk of electrical shock. Do not attempt to defeat this safety feature. Do not use this fan with any solid-state speed control devices.

Assembly Instructions

PRODUCT DESCRIPTION

The following parts are included:

• 1. Front Grille
• 2. Blade Cap
• 3. Fan Blade
• 4. Mounting Nut
• 5. Rear Grille
• 6. Motor Shaft
• 7. Oscillation Knob
• 8. Motor Housing
• 9. Speed Control (0, 1, 2, 3)
• 10. Set Screw / Fan Assembly
• 11. Inner Tube of Extension Pole
• 12. Height Adjustment Knob
• 13. Extension Pole
• 14. Base Screws x 4
• 15. Round Base
• 16. Cover

Assembly Steps

1. Remove the Extension Pole (#13). Align the holes at the bottom of the base pole with the Round Base (#15). Secure with the screws (#14) and tighten.
2. Remove/Loosen the Height Adjustment Knob (#12) from the Extension Pole (#13) by turning it clockwise.
3. Extend the Inner Tube Extension Pole (#11). Tighten the height adjustment knob (#12).
4. Remove/Loosen the Set Screw (#10) from the bottom of the fan assembly.
5. Place the fan assembly onto the Inner Tube of the Extension Pole (#11) and then tighten the Set Screw (#10) to secure it into position.
6. Unscrew the Mounting Nut (#4) located on the Motor Housing (#8) by turning it counter-clockwise.
7. Place the Rear Grille (#5) on the motor housing. Place the Mounting Nut back on and tighten by turning it clockwise.
8. Next, place the Fan Blade (#3) on the Motor Shaft (#6).
9. Place the Blade Cap (#2) on and tighten by turning it counter-clockwise.
10. Remove the screw on the front guard and open the clamps on the front grille (#1). Align the front grille with the back base screw. Tighten the screw on the front base and tighten the clamps.
11. Place the Cover (#16) on the Front Grille (#1).

Operation

1. Plug the power supply cord into an electrical outlet.
2. Use the controls below to adjust and customize airflow.

FAN SPEED

Press the Fan Speed / Off button to control the fan speed (OFF, Low, Medium, or High).

OSCILLATION CONTROL

Control the fan oscillation by pushing the knob Down/Up.

Tilt

Adjust fan head angle to set direction of airflow.

Height Adjustment

Adjust the height of the fan.

Care and Maintenance

⚠ WARNING

• Unplug the fan from the electrical supply source before cleaning.
• Do not use water directly on the fan for cleaning metal surfaces.
• Never immerse the fan or any wires in water.
• Do not use harmful cleaners.
• Do not bend the blades.

Cleaning

1. Use a soft damp cloth, then wipe the surface of the fan. To remove dust from the grille, use a vacuum cleaner or remove the front grille by removing the securing screw on the edge of the grille with a screwdriver.
2. After cleaning, remount the grille and fasten the securing screw on the edge of the grille.
3. Do not use harmful cleaners.
4. Do not bend the blades.

STORAGE

Keep the unit in its original carton for storage. Wrap the power cord to avoid damage during storage.

Specifications

Warranty

RS International Canada Inc. ("Royal Sovereign") warrants each fan to be free from defects in material and workmanship. Our obligation under this warranty is limited to the repair or replacement, free of charge, when delivered to an authorized Royal Sovereign service center, of any defective part(s) thereof, other than parts damaged in transit. This warranty is in effect for the original purchaser, for a period of one year from the date of purchase and is not transferable. This warranty shall apply only if the fan is used in accordance with the factory-provided instructions which accompany it.

Exclusions

This warranty excludes and does not cover defects, malfunctions, or failures of your Royal Sovereign Fan, caused by repairs by unauthorized persons or service centers, mishandling, improper installation, modification, or unreasonable use, including incorrect voltage, acts of God, or failure to provide reasonable and necessary maintenance. This warranty is in lieu of any and all expressed warranties. In no event shall Royal Sovereign be liable for consequential or incidental damages. This limitation would not apply if you live in a location that does not permit the exclusion or limitation of incidental or consequential damages.

For product support and warranty questions, please visit us at www.royalsovereign.ca/pages/contacts.

Contact Information:

RS INTERNATIONAL CANADA INC.
191 Superior Blvd., Mississauga,
ON L5T 2L6 CANADA
TEL: +1) 866-961-6673
www.royalsovereign.ca