Parkside PDSSA 20-Li B2 Cordless Impact Wrench

Introduction

Welcome to your new Parkside product. This user manual is an integral part of the product and contains important information regarding safety, operation, and disposal. Please familiarize yourself with all operating and safety instructions before using the product.

Intended Use

This tool is designed for driving and removing screws, as well as for tightening and loosening nuts. It features a forward/reverse rotation, a 1/4" internal hexagon bit holder, and an LED work light. The impact function engages during tightening and loosening to apply rotational force.

This tool is intended for adult use. Adolescents over 16 years of age may only use the tool under supervision. The manufacturer is not liable for damages caused by improper use or incorrect operation. The tool is not intended for commercial use.

Equipment

The tool includes the following components:

• 1 Tool holder
• 2 Locking sleeve
• 3 Bit holder (magnetic)
• 4 Direction switch / lock
• 5 Belt clip
• 6 Battery status button
• 7 Battery display LED
• 8 Battery pack*
• 9 Battery pack release button
• 10 LED work light
• 11 ON/OFF switch / speed regulator
• 12 Adapter for 1/4" square drive
• 13 Bit holder
• 14 Fast charger*

*Battery and charger not included in the scope of delivery.

Scope of Delivery

• 1 Cordless Impact Wrench
• 1 Adapter for 1/4" square drive
• 1 1/4" Extension (50 mm)
• 1 Belt clip
• 1 Carrying case
• 1 User manual

Technical Data

• Rated voltage: 20 V DC
• No-load speed: 0–2800 min⁻¹
• Number of impacts: 0–3600 min⁻¹
• Max. torque: 180 Nm
• Suitable for metal screws: ≤ M8
• Suitable for wood screws: ≤ 8 mm
• Tool holder: 1/4"

Compatibility

The tool is part of the Parkside X20V Team series and can be operated with batteries from this series. Batteries from the X20V Team series must only be charged with chargers from the X20V Team series.

Recommended batteries: PAP 20 A1/PAP 20 A2/PAP 20 A3/ PAP 20 B1/PAP 20 B3/Smart PAPS 204 A1/Smart PAPS 208 A1.

Recommended chargers: PLG 20 A3/PLG 20 A4/PLG 20 C1/ PLG 20 C3/PDSLG 20 A1/B2/ Smart PLGS 2012 A1.

Noise and Vibration Emissions

Measured values determined according to EN 62841. The A-weighted sound pressure level of the power tool is typically:

• Sound pressure level (LPA): 86 dB
• Uncertainty (KPA): 3 dB
• Sound power level (LWA): 94 dB
• Uncertainty (KWA): 3 dB

Vibration total values (vector sum of three directions) determined according to EN 62841:

• For tightening screws and nuts of maximum permissible size (an): 5.677 m/s²
• Uncertainty (K): 1.5 m/s²

[Attention] Wear hearing protection!

Note: The specified vibration and noise emission values are measured using standardized test procedures and can be used to compare power tools. They can also provide a preliminary assessment of exposure.

WARNING! Vibration and noise emissions may differ from the stated values during actual use, depending on the type and manner of use, and the workpiece being processed.

Try to keep exposure as low as possible. Measures to reduce vibration exposure include wearing gloves and limiting working time. Consider all parts of the operating cycle (e.g., times when the tool is switched off or running without load).

General Safety Instructions for Power Tools

1. Workplace Safety

• Keep your work area clean and well-lit. Cluttered or dark areas can lead to accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite dust or fumes.
• Keep children and other persons away while operating the power tool. Distractions can cause you to lose control.

2. Electrical Safety

• The power tool plug must match the socket. Do not modify the plug. Do not use adapter plugs with earthed power tools. Unmodified plugs and matching sockets reduce the risk of electric shock.
• Avoid body contact with earthed surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed.
• Keep power tools away from rain or wet conditions. Water entering a power tool increases the risk of electric shock.
• Do not misuse the power cord. Do not use it for carrying, pulling, or unplugging the power tool. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or tangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Using an outdoor-suitable extension cord reduces the risk of electric shock.
• If operating a power tool in a damp environment is unavoidable, use a residual current device (RCD). Using an RCD reduces the risk of electric shock.

3. Safety of Persons

• Be attentive, watch what you are doing, and use common sense when operating a power tool. Do not use the power tool if you are tired, or under the influence of drugs, alcohol, or medication. A moment of inattention can lead to serious injury.
• Wear personal protective equipment, including safety glasses. Personal protective equipment, such as a dust mask, non-slip safety shoes, hard hat, or hearing protection, depending on the type and use of the power tool, reduces the risk of injury.
• Avoid unintentional starting. Ensure the power tool is switched off before connecting it to the power supply and/or battery pack, before picking it up, or carrying it. Carrying the power tool with your finger on the switch or connecting the power tool to the power supply while it is switched on can lead to accidents.
• Remove any adjusting tools or wrenches before switching on the power tool. A tool or wrench left in a rotating part of the power tool can cause personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Wear appropriate clothing. Do not wear loose clothing or jewelry. Keep hair and clothing away from moving parts. Loose clothing, jewelry, or long hair can be caught by moving parts.
• If dust extraction and collection facilities can be connected, ensure they are connected and properly used. The use of dust extraction can reduce dust-related hazards.
• Do not be complacent and disregard safety rules for power tools, even if you are familiar with the tool after frequent use. Careless actions can cause serious injury in fractions of a second.

4. Use and Handling of Power Tools

• Do not overload the power tool. Use the correct power tool for your application. The right power tool will do the job better and safer at the rate for which it was designed.
• Do not use a power tool if the switch does not turn it on or off. A power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug and/or remove the detachable battery pack before making any adjustments, changing accessories, or storing the power tool. These preventive safety measures reduce the risk of unintentionally starting the power tool.
• Store idle power tools out of the reach of children. Do not allow persons unfamiliar with the power tool or these instructions to operate it. Power tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories with care. Check for misalignment or binding of moving parts, breakage of parts, or any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Sharpened cutting tools are less likely to jam and are easier to control.
• Use the power tool, accessories, and bits etc., in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• Keep handles and gripping surfaces dry, clean, and free from oil and grease. Slippery handles and gripping surfaces do not allow for safe handling and control of the power tool in unexpected situations.

5. Use and Handling of Battery Tools

• Charge batteries only with chargers recommended by the manufacturer. A charger that is suitable for one type of battery may create a fire hazard when used with another battery.
• Use only the intended batteries in the power tools. Use of other batteries may result in injury and fire hazard.
• Keep the unused battery away from paper clips, coins, keys, nails, screws, or other small metal objects that could cause a short circuit of the battery terminals. A short circuit between battery terminals may cause burns or fire.
• In case of improper use, liquid may be ejected from the battery. Avoid contact with it. If contact occurs, flush with water. If liquid gets into eyes, seek medical attention. Ejected battery liquid may cause irritation or burns.
• Do not use a damaged or modified battery. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or injury.
• Do not expose a battery to fire or high temperatures. Fire or temperatures above 130°C (265°F) can cause an explosion.
• Follow all instructions for charging and do not charge the battery or power tool outside the temperature range specified in the operating instructions. Incorrect charging or charging outside the permitted temperature range can damage the battery and increase the risk of fire.

[Attention] EXPLOSION HAZARD! Never charge non-rechargeable batteries.

Protect the battery from heat, e.g., continuous sunlight, fire, water, and moisture. There is an explosion hazard.

6. Service

• Have your power tool repaired by qualified personnel using only original spare parts. This ensures that the safety of the power tool is maintained.
• Never service damaged batteries. All battery servicing should only be performed by the manufacturer or authorized customer service centers.

Specific Safety Instructions for Impact Wrenches

• Wear hearing protection when using the impact wrench. Exposure to noise can cause hearing loss.
• Secure the workpiece. A workpiece held by clamping devices or a vice is held more securely than by hand.
• Hold the power tool firmly. High reaction torques can occur briefly when tightening and loosening screws.
• Wait until the power tool has come to a complete stop before setting it down. The accessory can get jammed and lead to loss of control of the power tool.
• Hold the power tool by the insulated gripping surfaces when performing an operation where the fastener may contact hidden wiring. Contact with a live wire may also make exposed metal parts of the power tool live and cause an electric shock.

Original Accessories / Attachments

Only use accessories and attachments specified in the user manual or whose mounting is compatible with the device.

[Warning] Do not use accessories not recommended by PARKSIDE. This can lead to electric shock and fire.

ACHTUNG! Hot surface. Risk of burns.

Before Use

Charging the Battery Pack (See Fig. A)

[Attention] Always unplug the charger before removing or inserting the battery pack.

[Warning] Observe the safety instructions and the instructions for charging and correct use provided in the user manual for your battery and charger of the 20V series.

A detailed description of the charging process and further information can be found in the separate operating instructions.

Note: It is ideal to fully charge the battery before putting it into operation. Li-ion batteries can be recharged at any time without shortening their lifespan. Interrupting the charging process does not damage the battery.

Never charge the battery pack if the ambient temperature is below 10°C or above 40°C. If a lithium-ion battery is to be stored for a long time, the charge level must be checked regularly. The optimal charge level is between 50% and 80%. The storage climate should be cool and dry, with an ambient temperature between 0°C and 50°C.

The recommended ambient temperature range for use with tools and batteries is between -5°C and 50°C.

• If necessary, remove the battery from the device.
• Slide the battery pack 8 into the fast charger 14.
• Plug the power adapter into the socket.
• When charging is complete, disconnect the fast charger from the mains.
• Remove the battery pack 8 from the fast charger 14.
• Switch off the charger for at least 15 minutes between successive charging cycles. Unplug the power adapter for this.

Inserting / Removing the Battery Pack

Inserting Battery Pack

Move the direction switch 4 to the middle position (lock). Slide the battery pack 8 into the handle until it clicks into place.

Removing Battery Pack

Press the release button 9 and remove the battery pack 8.

Checking Battery Status

To check the battery status, press the battery status button 6 (see main illustration).

The charge level is indicated by the battery display LED 7 as follows:

• RED/ORANGE/GREEN = Full charge
• RED/ORANGE = Medium charge
• RED = Low charge – charge battery

Operation

Switching On/Off

Switching On

To start the device, press and hold the ON/OFF switch 11. The LED work light 10 illuminates when the ON/OFF switch 11 is pressed lightly or fully, illuminating the work area in poor lighting conditions.

Switching Off

Release the ON/OFF switch 11 to switch off the device.

Adjusting Speed / Tightening Torque

Light pressure on the ON/OFF switch 11 results in low speed/tightening torque. Increasing pressure increases the speed/tightening torque.

The tightening torque depends on the selected speed and the duration of the impact.

[Attention] The actual achieved tightening torque must always be checked with a torque wrench!

Note: The integrated motor brake ensures a quick stop.

Changing Direction

Change the direction of rotation by pressing the direction switch 4 to the right or left.

Inserting Bits

Insert the adapter 12 or bit holder 13 into the tool holder 1. Pull the locking sleeve 2 back and allow the adapter 12 or bit holder 13 to click into place.

Maintenance and Cleaning

[Warning] RISK OF INJURY! Switch off the device and remove the battery before performing any work on the device. The device is maintenance-free.

The device must always be kept clean, dry, and free from oil or grease. Liquids must not enter the device.

Use a dry cloth to clean the housing. Never use gasoline, solvents, or cleaning agents that attack plastic.

If a lithium-ion battery is to be stored for a long time, the charge level must be checked regularly. The optimal charge level is between 50% and 80%. The optimal storage climate is cool and dry.

Disposal

[Icon: Crossed-out wheelie bin] Do not dispose of power tools in household waste!

The adjacent symbol of a crossed-out wheelie bin indicates that this device is subject to Directive 2012/19/EU. This directive states that at the end of its service life, this device must not be disposed of with normal household waste, but must be handed in at specially designated collection points, recycling centers, or disposal companies.

This disposal is free of charge for you. Protect the environment and dispose of it properly.

For the German market: When purchasing a new device, you have the right to return a corresponding old device to your dealer. Dealers of electrical and electronic equipment, as well as food retailers who regularly sell electrical and electronic equipment, are obliged to take back up to three old devices free of charge, even without the purchase of a new device, if the old devices are no larger than 25 cm. LIDL offers you return options directly in its branches and markets.

If your old device contains personal data, you are responsible for deleting them before returning it.

If possible without damaging the old device, remove old batteries or rechargeable batteries, as well as lamps, before returning the old device for disposal, and hand them in for separate collection. For built-in batteries, it must be pointed out during disposal that the device contains a battery.

[Icon: Recycling symbol with 'b'] Further options for the disposal of the used product can be obtained from your local municipality or city administration.

The packaging consists of environmentally friendly materials that can be disposed of at local recycling centers.

Dispose of the packaging in an environmentally friendly manner. Observe the markings on the various packaging materials and separate them if necessary. The packaging materials are marked with abbreviations (a) and numbers (b) with the following meaning:

• 1–7: Plastics
• 20–22: Paper and cardboard
• 80–98: Composite materials

Warranty of Kompernaß Handels GmbH

You receive a 3-year warranty on this device from the date of purchase. If included in the scope of delivery, you also receive a 3-year warranty on the battery packs of the X12V and X20V Team series from the date of purchase. In the event of defects in this product, you have statutory rights against the seller of the product. These statutory rights are not restricted by our warranty described below.

Warranty Conditions

The warranty period begins on the date of purchase. Please keep the receipt safe, as it is required as proof of purchase.

If a material or manufacturing defect occurs within three years of the purchase date of this product, we will repair, replace, or refund the purchase price free of charge, at our discretion. This warranty service requires that the defective device and proof of purchase (receipt) are presented within the three-year period, along with a brief written description of the defect and when it occurred.

If the defect is covered by our warranty, you will receive the repaired or a new product back. Repair or replacement of the product does not start a new warranty period.

Warranty Period and Statutory Warranty Claims: The warranty period is not extended by warranty service. This also applies to replaced and repaired parts. Any damage and defects present at the time of purchase must be reported immediately after unpacking. Repairs after the warranty period has expired are subject to a charge.

Warranty Scope

The device was manufactured according to strict quality guidelines and carefully checked before delivery. The warranty applies to material or manufacturing defects. The warranty does not cover parts subject to normal wear and tear, such as saw blades, replacement blades, sandpaper, etc., or damage to fragile parts such as switches or glass components.

This warranty is void if the product is damaged, used improperly, or not maintained. All instructions in the user manual must be followed precisely for proper use of the product. Uses and actions that are advised against or warned against in the user manual must be strictly avoided.

The product is intended for private use only and not for commercial use. Misuse, improper handling, force, or unauthorized modifications will void the warranty.

[Warning] Warranty service does not apply to:

• Normal wear and tear of battery capacity
• Commercial use of the product
• Damage or modification of the product by the customer
• Disregard of safety and maintenance regulations, operating errors
• Damage due to natural disasters

Handling Warranty Claims

To ensure prompt processing of your request, please follow these instructions:

• For all inquiries, please have the receipt and the article number (IAN) 479364_2410 ready as proof of purchase.
• The article number can be found on the type plate of the product, an engraving on the product, the title page of the user manual (bottom left), or on the sticker on the back or underside of the product.
• Should functional errors or other defects occur, please first contact the service department listed below by telephone or use our contact form, which you can find on parkside-diy.com in the Service category.
• A product identified as defective can then be sent postage-free to the service address provided, along with proof of purchase (receipt) and a description of the defect and when it occurred.

[Image Description: QR code linking to parkside-diy.com] On parkside-diy.com, you can view and download this and many other manuals. Use this QR code to go directly to parkside-diy.com. Select your country and search for the user manuals using the search mask. By entering the article number (IAN) 479364_2410, you will get to the user manual for your item.

[Warning] Have your devices repaired by the service center or an electrician and only with original spare parts. This ensures that the safety of the device is maintained.

Service

DE Germany
Tel.: 0800 8855 300
Contact form on parkside-diy.com

AT Austria
Tel.: 0800 447 750
Contact form on parkside-diy.com

CH Switzerland
Tel.: 0800 563 601
Contact form on parkside-diy.com

IAN 479364_2410

Importer

Please note that the following address is not a service address. Please contact the named service center first.

KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
DEUTSCHLAND
www.kompernass.com

Original Declaration of Conformity

We, KOMPERNASS HANDELS GMBH, document responsible: Mr. Semi Uguzlu, BURGSTR. 21, 44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards, normative documents, and EC directives:

Machinery Directive (2006/42/EC)

Electromagnetic Compatibility (2014/30/EU)

RoHS Directive (2011/65/EU)*

* The sole responsibility for the issuance of this declaration of conformity lies with the manufacturer. The object of the declaration described above complies with the provisions of Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

Applied Harmonised Standards

• EN 62841-1:2015/A11:2022
• EN 62841-2-2:2014
• EN 55014-1:2021
• EN 55014-2:2021
• EN IEC 63000:2018

Type/Device Designation: Cordless Impact Wrench PDSSA 20-Li B2

Year of Manufacture: 01-2025

Serial Number: IAN 479364_2410

Bochum, 13.10.2024

[CE Mark]

Semi Uguzlu
- Quality Manager

Technical changes in the interest of further development are reserved.

Replacement Battery and Charger Order

You can conveniently order replacement batteries or chargers online at www.kompernass.com.

[Image Description: Parkside X20V Team logo and QR code] Scan the QR code with your smartphone/tablet. This QR code will take you directly to our website where you can view and order available replacement parts.

Note: If you have problems with online ordering, you can contact our service center by phone or email. Always provide the article number (IAN) 479364_2410 when placing your order. Please note that online ordering of spare parts is not possible for all delivery countries.