LINOVISION POE-SW308G-4BT User Manual
Important Safeguards & Warning
Attention:
Please read the following safeguards and warnings carefully before using the product in order to avoid damage and loss.
Note:
- Do not expose the device to dust, high humidity, or dirt. Doing so may cause fire or electric shock.
- Do not install the device in direct sunlight as it may cause overheating and failure. Installation of the units should be via the compatible rack mount or securely on a flat surface.
- Do not place the device on carpet or around the unit. Doing so may cause overheating, failure, or fire.
- Do not stack or place objects on the unit.
- This unit contains no user-serviceable parts; servicing should only be performed by approved technicians.
Warning:
Do not use a power supply other than the provided manufacturer power supply. Failure to do so may cause unit failure or damage.
Special Announcements:
This manual is for reference only. All designs and software are subject to change without prior notice.
Product Overview
Introduction:
LINOVISION's POE-SW308G-4BT 802.3bt PoE++ switch is a compact yet powerful networking solution designed to support the increasing demand for high-power devices. This switch provides Power over Ethernet Plus Plus (PoE++) capability, delivering up to 90W on the first 4 ports, making it ideal for powering high-performance devices such as PTZ cameras, WiFi6 access points, LED lighting, and industrial equipment.
Engineered for reliability and efficiency, LINOVISION's PoE++ switches feature gigabit Ethernet support and robust safety mechanisms like surge protection and overcurrent prevention. Their plug-and-play design ensures quick setup, while the compact form factor makes them suitable for both office and industrial environments. These 802.3bt PoE++ switches offer tremendous value by reducing infrastructure costs and simplifying deployment. They eliminate the need for separate power supplies, enhance energy efficiency, and provide scalable solutions tailored to small-to-medium networks or edge deployments.
Common Features:
- 802.3bt commercial PoE++ switch.
- Supports IEEE 802.3af, IEEE 802.3at, and IEEE 802.3bt standards.
- Supports PoE Power up to 90 watts for PoE++ ports.
- Complies with IEEE802.3, IEEE802.3u, IEEE802.ab, IEEE802.z.
- MAC auto study and aging, MAC address list capacity is 8k.
- All RJ45 ports self-adapt MDI/MDIX mode.
- All RJ45 ports self-adaptive 10/100/1000Mbps.
- Commercial wide temperature design (-4°F to 131°F / -20°C to 55°C).
- Supports 6KV ESD protection on all ports.
Typical Application:
Diagram Description: A network diagram illustrates the typical application of the POE-SW308G-4BT switch. It shows two cameras and one Wi-Fi AP connected to the switch via Ethernet cables. The switch also has an SFP fiber port connected to a network backbone. A PC or NVR is connected to the switch via an Ethernet cable. The diagram indicates that the cameras and Wi-Fi AP are powered by PoE++ and PoE+ respectively, originating from the switch.
Operation Guide:
Please check and confirm the following notes before installation:
- If the PoE port meets the power requirements of the connecting device.
- If the PoE standard requirements and power supply match the connecting devices.
- If the output power of the matched power adapters is compatible with the specification of the adapters.
Follow these steps to install the PoE switch:
- Place the PoE switch on a table, wall, or rack.
- Connect the power outlets through the power cable.
Caution:
- Please do not place heavy products on the PoE switch and ensure good ventilation environments for the PoE switch.
- Please cut off the power first before plugging in the power adapter.
- Indoor use only.
Panel View
Diagram Description: The front panel of the POE-SW308G-4BT switch is depicted. It features various ports and indicators:
- Indicators: SFP Indicator (Link/Green), Link/ACT Indicator (Green), PoE Indicator (Yellow), Power Indicator (Green).
- Ports: 4 x 90W Gigabit PoE Ports, 4 x 30W Gigabit PoE Ports, 1 x Gigabit Uplink Port (RJ45), 1 x Gigabit SFP Port.
- Other: Ground terminal, AC Input (100-240V), PoE Extend Mode switch.
Technical Specification
Hardware Specifications
| Specification | Details |
|---|---|
| Model | POE-SW308G-4BT |
| Connector | 10*10/100/1000BASE-T RJ45, 1*1000MBASE-X SFP |
| PoE Port | 4*10/100/1000Mbps PoE+ port, 4*10/100/1000Mbps PoE++ port |
| LED Indicators | Power Indicator: PWR(green). Network Indicator: Link(green). PoE Working Indicator: PoE(yellow). SFP Indicator: Link(green) |
| Switch Architecture | Store and Forward |
| Backplane Bandwidth | 24Gbps |
| Packet Forwarding Rate | 17.86Mpps |
| MAC Address | 8k |
| Power Requirement | AC100-240V 50/60Hz |
| ESD Protection | 6KV ESD |
| Dimension (W×D×H) | 250mm x 180mm x 44.5mm |
| Weight | 4.41lb (2Kg) |
Power over Ethernet (PoE) Specifications
| Specification | Details |
|---|---|
| Network Standard | IEEE802.3i 10 BASE-T, IEEE802.3u 100 BASE-TX, IEEE802.3ab/z 1000 BASE-TX, IEEE802.3x Flow Control |
| PoE Standard | IEEE 802.3 af/at/bt |
| PoE Supply Type | 1/2/4/5(+), 3/6/7/8(-) |
| PoE Power Output | Max. 90W (Single Port) |
| PoE Power Budget | Total 120W |
Environment Specification
| Specification | Details |
|---|---|
| Operating Temperature | -4°F to 131°F (-20°C to 55°C) |
| Storage Temperature | -4°F to 131°F (-20°C to 75°C) |
| Operating Humidity | 5% to 95% (non-condensing) |
| Storage Humidity | 5% to 95% (non-condensing) |
Safety
FCC Part15 Class A, CE, RoHS
Warranty Card
This section contains fields for warranty information, including:
- Product Name, Product Model, Customer Name, Address, Telephone, Email, Linkman, Zip Code, Fax, Shipping Date.
- Quality Certificate: Checked By, Date.
The warranty card is only valid when filled in and the product is registered for repair.
