Safety Information and Specifications
⚠ IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
CAUTION: Do not use this product for any purpose not explicitly specified by Rocketfish. Improper installation may cause property damage or personal injury. If you do not understand these directions, or have doubts about the safety of the installation, contact Customer Service or call a qualified contractor. Rocketfish is not responsible for damage or injury caused by incorrect installation or use.
- Maximum TV weight: 100 lbs. (45.3 kg)
- Screen size: 40" to 75" diagonal
- Overall dimensions (H × W × D): 16.7 x 24.9 x 3.5 in. (425 x 632 x 90 mm)
- Wall-mount weight: 19.4 lbs. (8.8 kg)
We're here for you
For customer service, call: 1-800-620-2790 (U.S. and Canada)
The weight of your TV must not exceed 100 lbs. (45.3 kg). The wall must be capable of supporting five times the weight of your TV and wall mount combined.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children!
Tools Needed
You will need the following tools to assemble your new TV wall mount:
- Edge-to-edge stud finder
- Pencil
- Level
- Drill
- Phillips screwdriver
- Measuring tape
- Socket wrench with 1/2" (13 mm) socket or adjustable wrench
- Hammer
- 7/32" (5.5 mm) wood drill bit for wood stud wall
- 3/8" (10 mm) masonry drill bit (concrete only)
Package Contents
Make sure that you have all the hardware necessary to assemble your new TV wall mount:
- 1 Vertical Brackets (Qty. 2)
- 2 Horizontal brackets (Qty. 2)
- 3 Wall plate (Qty. 1)
- 4 Arm (Qty. 1)
- 5 Template (Qty. 1)
TV Hardware
The following hardware is included:
| Lbl | Hardware | Qty. | Lbl | Hardware | Qty. |
|---|---|---|---|---|---|
| 6 | M6/M8 washers | 4 | 14 | M8 x 35 mm screw | 4 |
| 7 | 2.5 mm spacers | 4 | 15 | M8 x 45 mm screw | 4 |
| 8 | 22 mm spacers | 4 | 16 | M8 x 50 mm screw | 4 |
| 9 | M6 x 12 mm screw | 4 | 17 | M4 x 18 mm screw | 4 |
| 10 | M8 x 16 mm screw | 4 | 18 | 5/16" x 2 3/4" lag screw | 4 |
| 11 | M8 x 20 mm screw | 4 | 19 | Securement screw | 2 |
| 12 | M8 x 25 mm screw | 4 | 20 | 4 mm hex key | 1 |
| 13 | M6 x 35 mm screw | 4 | 21 | TV interface screw | 2 |
Concrete Installation Kit CMK1 (not included)
Contact customer service at 1-800-359-5520 to have these additional parts shipped directly to you.
- 22 Concrete anchors (Fischer UX10 x 60R) (Qty. 4)
A ruler is shown with markings for inches (4in) and millimeters (100mm).
Installation Instructions
Step 1 - Determine whether your TV has a flat back or an irregular or obstructed back
- Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches.
- If your TV has a table-top stand attached, remove the stand. Refer to the documentation that came with your TV for instructions.
- Temporarily lay the vertical brackets (1) on the back of your TV.
- Align the screw holes in the vertical brackets with the mounting screw holes on your TV.
- Identify which type of back your TV may have:
- Flat back: The brackets lay flush against the back of your TV and do not block any jacks. Spacers are not needed.
- Obstructed back: The brackets block jacks on the back of your TV. Use spacers (7 or 8) when assembling the wall mount.
- Irregularly-shaped back: There is a gap between the brackets and some part of the back of your TV. Use spacers (7 or 8) when assembling the wall mount.
- Remove the vertical brackets.
Diagrams illustrate bracket placement on different TV back types, showing where spacers might be needed.
Step 2 - Select screws, washers, and spacers
- Select the hardware for your TV (screws, washers, and spacers). Some TVs include mounting hardware. If your TV came with screws, they are likely already in the back of the TV. If you are unsure of the correct screw length, test various sizes by hand threading them.
- Available screws: M6 x 12 mm (9), M8 x 16 mm (10), M8 x 20 mm (11), M8 x 25 mm (12), M6 x 35 mm (13), M8 x 35 mm (14), M8 x 45 mm (15), M8 x 50 mm (16).
- Use M6/M8 washers (6) for all screws.
- For an irregular or obstructed TV back, use the 2.5 mm (7) or 22 mm spacers (8).
CAUTION: To avoid potential personal injuries and property damage, ensure adequate threads secure the brackets to your TV. If resistance is met, stop immediately and contact customer service. Use the shortest screw and spacer combination that fits your TV. Using hardware that is too long may damage your TV. Using a screw that is too short may cause your TV to fall from the mount.
Diagrams show a screw fitting correctly, a screw that is too long, and a screw that is too short.
- Remove the screws.
- For a flat back TV, proceed to "STEP 3 - Option 1: Attaching the vertical brackets to TVs with a flat back" on page 7.
- For an irregular or obstructed back, proceed to "STEP 3 - Option 2: Attaching the vertical brackets to TVs with irregular or obstructed backs" on page 8.
Step 3 - Option 1: Attaching the vertical brackets to TVs with a flat back
- Align the holes on the vertical brackets (1) with the screw holes on the back of your TV. Ensure the brackets are level.
- Place washers (6) over the bracket holes that align with the TV screw holes. Insert screws (9, 10, 11, or 12) through the washers.
- Tighten the screws until snug against the vertical brackets. Do not over-tighten.
You'll need:
- Screws: 9 (Qty.4), 10 (Qty.4), 11 (Qty.4), or 12 (Qty.4)
- Washers: 6 (Qty.4)
- 1 Vertical Brackets (Qty.2)
- Phillips screwdriver
- Level
Step 3 - Option 2: Attaching the vertical brackets to TVs with irregular or obstructed backs
- Place the 2.5 mm (7) or 22 mm spacers (8) over the screw holes on the back of the TV.
- Align the vertical brackets (1) over the spacers (7 or 8). Place washers (6) over the bracket holes and insert screws (13, 14, 15, or 16) through the washers, brackets, and spacers. Ensure the brackets are level.
- Tighten the screws until snug against the vertical brackets. Do not over-tighten.
You'll need:
- Screws: 13 (Qty.4), 14 (Qty.4), 15 (Qty.4), or 16 (Qty.4)
- Spacers: 7 (Qty.4) or 8 (Qty.4)
- Washers: 6 (Qty.4)
- 1 Vertical brackets (Qty. 2)
- Phillips screwdriver
- Level
Step 4 - Attaching the horizontal brackets
- Slide the horizontal brackets (2) through the slots in the vertical brackets (1), ensuring they are centered.
- Secure the horizontal brackets (2) to the vertical brackets (1) using M4 x 18 screws (17). Tighten until snug. Do not over-tighten.
You'll need:
- 2 Horizontal brackets (Qty.2)
- Screws: 17 (Qty.4)
- Phillips screwdriver
Step 5 - Determine wall-mount location
NOTE: For detailed information on determining hole placement, visit http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder.
Your TV should be positioned so your eyes are level with the middle of the screen, typically 40 to 60 inches from the ground.
The center of your TV should align with the center of the wall plate (3). Before drilling:
- Measure the distance from the bottom of your TV to the middle of the four mounting screw holes. This is measurement 'a'.
- Measure the distance from the floor to where you want the bottom of the TV placed on the wall. Ensure the TV is above furniture (e.g., entertainment centers, TV stands) and items on the furniture (e.g., Blu-ray players, cable boxes). This is measurement 'b'.
- Calculate the total height: a + b. This is the desired height for the center of the wall plate (3) on the wall.
- Mark this spot on the wall with a pencil.
You'll need:
- Measuring tape
- Pencil
Diagram shows measurements 'a' (TV bottom to bracket holes) and 'b' (floor to TV bottom) on a TV stand setup.
Step 6 - Option 1: Installing on a wood stud wall
Note: Drywall covering the wall must not exceed 5/8" (16 mm).
- Locate a stud. Verify its center using an edge-to-edge stud finder.
- Ensure the distance between studs is 16 inches.
- Align the center of the wall plate template (5) at the determined height. Ensure it is level. Tape the template to the wall and mark the four lag screw hole locations at the stud centers. Remove the template.
- Drill four pilot holes to a depth of 2 3/4 in. (69 mm) using a 7/32 in. (5.5 mm) diameter drill bit.
Diagram shows a stud finder locating a stud, a wall with 16-inch spacing indicated, and pilot holes being drilled. Notes specify minimum wood stud size: Common 2 x 4 in. (51 x 102 mm) or Nominal 1.5 x 3.5 in. (38 x 89 mm).
You'll need:
- Lag screw 18 (Qty.4)
- Level
- Template 5
- Edge-to-edge stud finder
- Drill
- Wall plate 3
- Pencil
- 7/32" wood drill bit
- Tape
- 1/2" socket wrench
Installation:
- Align the wall plate (3) with the pilot holes. Insert lag screws (18) through the wall plate assembly holes and tighten until firm against the wall.
CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the lag screws (18).
Step 6 - Option 2: Installing on a solid concrete or concrete block wall
CAUTION: To prevent property damage or personal injury, never drill into the mortar between blocks. Mount the wall plate directly onto the concrete surface.
Note: Minimum solid concrete thickness: 8 in (203 mm). Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm).
- Align the center of the wall plate template (5) at the determined height. Ensure it is level. Tape the template to the wall and mark the four lag screw hole locations. Remove the template.
- Drill pilot holes to a depth of 3 in. (76 mm) using a 3/8 in. (10 mm) diameter masonry drill bit.
- Insert the concrete wall anchors (22) (refer to "Concrete Installation Kit CMK1 (not included)" on page 4) into the pilot holes and use a hammer to ensure they are flush with the concrete surface.
Diagrams show drilling pilot holes into concrete, indicating depth and drill bit size (3 in / 76 mm, 3/8 in / 10 mm), and inserting anchors with a hammer.
You'll need:
- Wall plate 3
- Template (5)
- Level
- Hammer
- Drill
- 1/2" socket wrench
- Concrete anchor 22 (Qty.4)
- Lag screw 18 (Qty.4)
- 3/8" masonry drill bit
- Pencil
- Tape
Installation:
- Align the wall plate (3) with the anchors. Insert lag screws (18) through the wall plate assembly holes and tighten until firm against the wall plate.
CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the lag screws (18).
Step 7 - Attach the arm to the wall plate
- Hang the arm (4) onto the wall plate (3) by first hooking the top support, then lowering the bottom of the arm into place.
- Lock the arm (4) to the wall plate (3) with the securement screws (19), using the hex key (20).
IMPORTANT: These securement screws must be installed to secure the TV onto the wall plate assembly.
You'll need:
- Arm 4
- Securement screws 19 (Qty.2)
- Hex key 20
Diagrams show the arm being hung on the wall plate and then secured with screws.
Step 8 - Attach the TV to the arm
- To make it easier to attach your TV, position the arm (4) so the elbow is bent 90 degrees and pressed against the wall.
- Hang the TV onto the arm (4) by first hooking the top support, then lowering the bottom of the TV into place.
- Lock the TV to the arm (4) with the TV interface screws (21).
IMPORTANT: The two TV interface screws must be installed to secure the TV onto the wall plate assembly.
HEAVY! You will need assistance with this step.
You'll need:
- Level
- TV interface screw 21 (Qty. 2)
- Hex key 20
Diagrams show the TV being hung on the arm and secured with screws.
Step 9 - Making adjustments and managing cables
- Adjustments are available by loosening the tilt control knob.
NOTE: Once your TV is in place, tighten the tilt tension knob to prevent unwanted movement.
Diagrams illustrate TV tilt adjustments (up/down for viewing angle) and the fully articulating arm with three pivot points for viewing positions. Angles of 5° and 10° are indicated.
- Manage cables by fully extending the arms to provide enough slack, then routing cables along the arms and inserting them into the channels on the arms for a clean look.
Removing the TV from the wall mount
- To remove your TV from the wall plate assembly, disconnect all cables, then reverse the procedures in Step 8.
IMPORTANT: Your TV is heavy. You may need assistance with this step.
For customer service, call: 1-800-620-2790 (U.S. and Canada)
