RF48 User Manual
1 Appearance
The RF48 remote control is a handheld device with a vertical layout. At the top, it features buttons labeled 'ZG', 'TV', 'M1', and 'M2'. Below these are directional control buttons, indicated by icons for moving the head up and down, the feet up and down, and the lumbar support up and down. Further down the remote, there are buttons for 'TIMER', 'FOOT', 'MODE', and 'ON/OFF'. A prominent lock icon is also present, likely for the child lock feature.
2 Key Function
| Key value | Specification |
|---|---|
| PAIR | press and hold [pairing button] and [button], the remote enters pairing mode |
| HEAD UP | Press and hold [head up button], head actuator moves out, stop when released |
| HEAD DOWN | Press and hold [head down button], head actuator moves in, stop when released |
| FOOT UP | Press and hold [foot up button], foot actuator moves out, stop when released |
| FOOT DOWN | Press and hold [foot down button], foot actuator moves in, stop when released |
| LUMBAR UP | Press and hold [lumbar up button], Lumbar actuator moves out, stop when released |
| LUMBAR DOWN | Press and hold [lumbar down button], Lumbar actuator moves in, stop when released |
| FLAT | Press and hold [flat button], the bed goes flat |
| ZG | Click [ZG button], the bed moves to zeroG position, press and hold zeroG button for 5s, until backlight flashes, the control set the current position as zeroG position |
| TV | Click [TV button], the bed moves to TV position, press and hold TV button for 5s, until backlight flashes, the control set the current position as TV position |
| Antisnore | Click [Antisnore button], the bed moves to Antisnore position, press and hold Antisnore button for 5s, until backlight flashes, the control set the current position as Antisnore position |
| M1 | Click [M1 button], the bed moves to M1 position, press and hold M1 button for 5s until backlight flashes, the control set the current position as M1 position |
| M2 | Click [M2 button], the bed moves to M2 position, press and hold M2 button for 5s, until backlight flashes, the control set the current position as M2 position |
| UBB | Click [light button], open or close under bed light |
| CHILD LOCK | press and hold [lock button] button for 5s until backlight flashes, then the lock/unlock is complete. In locked state, press any button except this button and the pairing button, the backlight flashes |
| Massage head+ | Click [head massage button], head massage motor switches massage intensity, massage intensity switches among 0-1-2-3 |
| Massage timer | Click [timer button]. If the massage motors do not work, the button is invalid, if the massage motors work, click the button to switch the massage time, when massage time switch to 0, turn off the massage. |
| Massage foot+ | Click [foot massage button], foot massage motor switches massage intensity, massage intensity switches among 0-1-2-3 |
| Massage Mode | Click [mode button], to switch the massage mode or massage motors, massage mode switches among type0→type1→type2→type3→type0; this button can only switch the massage mode, it can not open massage motors. |
| MASSAGE ON/OFF | click [ON/OFF button] button to turn on/off head&foot massage |
FCC Warning
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ISED Warning
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
