MC56F80000-EVK | NXP Semiconductors
User Guide for NXP models including: MC56F80000 Evaluation Kit, MC56F80000, Evaluation Kit, Kit
MC56F80000-EVK | NXP Semiconductors
File Info : application/pdf, 4 Pages, 1.98MB
DocumentDocumentQUICK START GUIDE MC56F80000-EVK MC56F80000 EVALUATION KIT GET TO KNOW THE MC56F80000-EVK Power/USB Power/USB Virtual OpenSDA and Serial Port (CP210x Virtual Serial Port is DNP by Default SW5 SW3 SW4 SW2 J7 Adapter/ 5 V Only J11 Reset Source Selection Jumper SW1 Reset JTAG Port for 56F80748 J3 I/O Header J4 I/O Header J2 I/O Header J1 I/O Header NC-2 VDD-4 RESET-6 VDD-8 P5V-10 GND-12 GND-14 P5V_DC_IN-16 ANA3/3B-2 GA4-4 GA5-6 GB1-8 GB4-10 GB5-12 1-GF1 3-GE7 5-GE4 7-GE5 9-GE2 11-GE3 13-GE0 15-GE1 1-NC 3-NC 5-NC 7-NC 9-NC 11-NC NC-19 NC-17 ADC-MID-15 GB1_OPB_P-13 GA1_OPA_P-11 GB2_RC-9 GA2_RC-7 GA3/GB3_RC-5 GB0_IN-3 GA0_IN-1 NC-15 NC-13 NC-11 NC-9 NC-7 NC-5 GC6-3 NC-1 20-GC15 18-GC14 16-AREF 14-GND 12-GC9 10-GC8 8-GC10 6-GE7 4-GE6 2-GF6 16-GC5 14-GC7 12-GF3 10-GC4 8-GF4 6-GF5 4-GC2 2-GC3 PWM LEDs User LEDs Figure 1: MC56F80000-EVK Callouts 2 Figure 2: MC56F80000-EVK Pin-Outs QUICK START GUIDE MC56F80000-EVK OPERATION NOTES 1. MC56F80000-EVK can be powered by either of the USB connectors (J12, J26), or the adapter input (J7). Beware that only an adapter with 5V output can be used. 2. When the board is powered up, a green LED D2 will illuminate, indicating 3.3V is on. If the board is powered by USB connector (J12), an orange LED D4 will also illuminate, indicating K26 is powered. 3. J12 is the on-board OPENSDA (realized by K26) connector which can be used to debug/program MC56F80748. It provides a virtual serial port as well. 4. J26 is the virtual serial port connector. CP210x USB to UART bridge VCP Drivers are needed. CP210x is not populated by default on the board. 5. J10 is the JTAG connector for MC56F80748. Remember to remove four jumpers on J13 when this JTAG is used. This is to avoid the impact of on-board OPENSDA circuit. 6. Pin2 and pin3 of J11 are connected by default to enable the external reset from SW1. 3 GET STARTED Download installation software and documentation under "Jump Start Your Design" at www.nxp.com/MC56F80000-EVK. SUPPORT Visit www.nxp.com/support for a list of phone numbers within your region. WARRANTY Visit www.nxp.com/warranty for complete warranty information. www.nxp.com/MC56F80000-EVK NXP, the NXP logo and NXP SECURE CONNECTIONS FOR A SMARTER WORLD are trademarks of NXP B.V. All other product or service names are the property of their respective owners. © 2022 NXP B.V. Document Number: MC56F80000QSG REV 0 Agile Number: 926- 54617 Rev A