INVANTI Voyage Electric Bicycle User Manual

Welcome

Thanks for choosing the INVANTI Electric Bicycle, and experiencing the pleasure brought to you by travel and fitness.

Ride legally in accordance with local laws and regulations.

Products & Accessories

Product Name: INVANTI Electric Bicycle

Model: EB19

Implementation Standard: UL2849

Bicycle Components Diagram Description:

A diagram shows an electric bicycle with components labeled: Electronic Display, Brake Lever, Handlebar clamp, Charging port, Cushion, Headlight, Front Fork, Reflector, Seatpost Clamp, Battery, Taillight, Reflector, Rear Disc Brake, Pedal, Derailleur, Motor, Front Disc Brake, Tire.

Included Accessories:

• Instructions
• Tools
• Power Adapter
• Keys
• Pedals

Please carefully check whether all items in the box are complete and intact.

Precautions for Use

Traffic Regulations and Safety:

• Obey traffic regulations and traffic safety.
• Persons under the age of 16 are prohibited from riding E-bikes on the road.
• Do not lend the E-bike to persons who cannot ride to avoid injury.
• Carry people or items with E-bike in accordance with laws and regulations.
• It is recommended to wear a helmet when riding and pay attention to traffic safety. It is strictly forbidden to hold the handlebar with one hand or ride with both hands away from the handlebar.
• Pay attention to slow down when riding in rain or snow, as the braking distance will be extended. Try to avoid riding in severe weather, such as heavy rain.

Safety Tips for E-bike Use:

• Do not park E-bike in building foyers, evacuation stairs, walkways, or safety exits.
• Do not charge and park E-bike in residential buildings; keep away from combustibles when charging, and the charging time shall not be too long.
• Use and maintain the battery correctly; used batteries shall not be dismantled without authorization and shall be recycled by a relevant professional department.
• Understand the safe use of the charger and warning terms.
• Replace the charger with one matching the storage battery model.
• Do not rinse with water to avoid the hidden danger of accidents caused by the soaking of internal electronic components and circuits.
• When adjusting the handlebar or seat, be careful not to expose the safety line marking of the handlebar stand tube and saddle tube (where applicable).
• The A-weighted emission sound pressure level at the driver's ears is less than 70dB(A).
• For your safety, do not tamper with other parts of the electric bicycle except the sprocket and non-original parts. If any parts are damaged, contact the local dealer for after-sales service.

Do not use the E-bike in off-road or other extreme sports scenes as it is not professional equipment for such activities. Prolonged exposure to UV rays, rain, and the elements may damage the enclosure materials. Please store indoors when not in use.

Operation & Use

NOTICE: The following steps are a general guide for e-bike assembly. Consult a certified bike mechanic for comprehensive assembly, maintenance, and repair.

Step 1: Unpack the E-bike

Open the bike box. Take out the seat and accessory box. With the help of another person, remove the e-bike from the box. Carefully remove packaging material. Please recycle packaging materials.

Step 2: Install the Handlebar

Diagram description: Rotate the stem towards the front of the bike and adjust the angle of the riser and frame to be relatively perpendicular to the fork. Remove the 4 front cover screws with an Allen key and take off the stem front cover. Place the handlebar into the stem and center its angle. Fasten the front cover, gradually tightening the 4 screws in order.

Step 3: Install the Pedals

Diagram description: Both ends of the left and right pedals are marked. Install the right pedal by tightening clockwise. Tighten the left pedal counterclockwise. Both pedals should be tightened with a torque wrench.

Step 4: Adjust the Saddle Height

• Open the seatpost clamp.
• Adjust the seatpost to a comfortable height, ensuring it is inserted past the minimum insertion point indicated on the seat post.
• Close the seatpost clamp lever.

Battery Installation and Removal

Step 5: Install the Rear Mudguard Bracket

Diagram description: Align the mudguard bracket with the screw holes, then insert screws and spacers and tighten them.

Step 6: Removing or Installing the Battery

• To remove the battery: Insert the key and unlock counterclockwise, then flip the switch lever. Remove the battery downwards. Store it in a safe place or perform charging operations.
• To install the battery: Push the battery into the battery compartment. After installing, insert the key and turn it clockwise to lock.
• Ensure the battery is properly secured to the bike before each use.

About Charging

Open the waterproof plug of the charging port on the upper right side of the battery and connect the charger to start charging. When the indicator light on the charger turns from red to green, the battery is fully charged.

Battery Safety Instructions:

• Do not dismantle or disperse battery cells.
• Keep the battery away from children.
• Do not disconnect the cathode and anode of the charger during charging and discharge process. Do not use any conductor to connect both terminals, as this will cause a short circuit.
• Do not expose the battery to water.
• It is prohibited to place the battery in temperatures over 60°C, near high-temperature heat sources like furnaces or fireplaces.
• Do not hit, throw, or trample batteries.
• Do not use tools or nails to lacerate and cut through the battery.
• If a leak occurs and electrolyte contacts eyes, do not rub. Wash immediately with plenty of water.
• If the battery has a smell, heat, smoke, changed colors, distortion, or any abnormal signs, stop using it immediately and move away.
• Store the battery in a clean, dry circumstance and charge it for 2 hours every two months if not used for a long time.

Protection:

• To extend battery life, use only the provided charger.
• Connect the charger to the power source, then connect the charger's output connector to the battery's input connector.
• Common single charging time is about 7.5 hours. Stop charging when the battery is full. Never charge a battery for more than 12 hours.
• Do not leave a charged battery unattended.
• Charge the battery timely after discharging to avoid over-discharge.

Storage Requirements:

• The lithium-ion battery cannot be stored in hot and high humidity places. Store between 20 to 55 degrees Celsius.
• The bike must be kept in a dry and clean area.
• The battery cannot be stored for a long time without charging. Charge the battery once a month. Store with a fully charged status.

WARNING - Risk of Fire and Electric Shock. No User Serviceable Parts.

Display Operation

Control Buttons:

Diagram description: Shows control buttons labeled Power button, Button "+", Button "-".

Functional Area Layout:

Diagram description: Shows the display layout with numbered indicators: 1. Cruise Control Sign, 2. Speed Unit, 3. Real Time Speed, 4. Power, 5. Data Area, 6. Bluetooth Connection, 7. Fault Alarm, 8. Boost Logo, 9. Boost Gear, 10. Headlight Status, 11. Speed Dial.

App Connection:

Please use your mobile phone to scan the QR code or search "Invanti", "InvantiMobility", "5thWheel" or "5thWheel-Trip" in the app store to download and install the App. Open the App, complete registration, and then add your bicycle by tapping "+" or the Search Devices button.

Button Definition:

General Operation:

Power on/off: Press and hold the power button.

Display Interface:

After the display is turned on, it shows real-time speed (SPEED) and trip distance (TRIP) by default. Pressing the "-" button cycles through TRIP, ODO, AVG, MAX, TIME, KCAL, POW, and VOLT.

Push Assistance:

When the speed is 0mph, press and hold the "-" button to enable electric push assistance mode (3mph). The instrument will display P. Applying any brake will stop power output. This function is only for pushing the e-bike.

Headlight On/Off:

Press and hold the "+" button to turn on headlights; press and hold it again to turn them off.

Assist Level Selection:

Press "+" or "-" to switch assist levels (0-5). 0 gear: no motor power. 1-5 gear: motor power increases. Throttle works in 0-5 gears.

Battery Level Indicator:

The battery level indicator consists of five segments. When the battery is fully charged, all segments are on. In case of undervoltage, the outline of the battery indicator will flash, indicating the battery needs charging.

Setting Mode:

Press "+" and "-" simultaneously to enter or exit the setting mode.

Error Code Indicator:

When a fault occurs, the display will show an error code. Definitions include: 10: Overcurrent protection, 11: Under voltage protection, 18: Position sensor failure, 70: Communication error. Conduct troubleshooting if an error code appears.

Attentions:

• Power off first before connecting and disconnecting cables to avoid display damage.
• Do not put the display into water.
• Clean the display with a wet and soft cloth; do not use chemical liquids or sprays.
• Dispose of the display and accessories according to local regulations for recycling.
• Damage or failure caused by improper installation or use is not covered by warranty.
• The manufacturer is not responsible for accidents caused by improper parameter setting.

Check Before Use

Final Check Before Each Ride:

• Handlebars: Check they are straight and secure.
• Wheels: Ensure front and rear mudguard stays are tight and the quick release mechanism is properly gripping the front wheel.
• Seat and Post: The seat and post should be straight, fastened tightly, and not exceed the max height indicator.
• Pedals and Chain: Pedals should be wound in and fully tightened. Gears should engage cleanly and change smoothly.
• Brakes: Test front and rear brakes by rolling the bike forwards; both wheels should stop completely. Ensure there is more than one finger thickness between the grip and the brake lever when fully depressed.
• Rack: Ensure the rack is secure and all bolts are tight.
• Kickstand: The kickstand shouldn't wobble; tighten if necessary.
• Tires: Pump tires to be very firm (impossible to deform with your thumb). Suggested tire pressure: 35~45 psi.
• Electrics: Test both lights.
• Battery: Fully charge the battery before use. Make sure the battery is in place and locked. Turn on the battery switch.

Adjusting the Height of the Seat:

Unlock the lever, adjust the seat height to the desired position without exceeding the mark on the seat's tube, then lock the lever. The seat height should allow your leg to be stretched when the corresponding pedal is in the lower position.

Riding Your E-bike:

After installation, turn on the e-bike. Loosen the bracket. Put one foot on the pedal to check safety before setting off. You will feel the motor assist. Battery power depletes sequentially. If the battery is depleted, turn off the main switch and use pedals only. Use both brakes together when stopping. Braking distance increases in wet conditions. Never ride through deep puddles or streams. Avoid loose or uneven surfaces. Do not carry extra passengers or heavy loads. Never ride under the influence of drugs or alcohol, or when feeling unwell. Always ride with lights at night. If you are new to cycling, practice in a quiet place to gain confidence.

Precautions Required Prior to Each Use:

• Check all lights and displays are working.
• Check regularly that the electrical connectors between the bike and battery are clean.
• Check the brakes: apply the front brake and push forward; the bike should not move. Repeat for the rear brake. Brake levers should not touch the handlebars and should work without excessive force.
• Make sure your clothing is suitable for riding; avoid long, loose, or flowing garments that could catch in wheels or chain.
• Wear an approved safety helmet.

Technical Parameters

Note on endurance mileage: This mileage is measured under specific conditions (mean speed of 9.3~20MPH, flat road without wind, 60kg load, temperature around 23°C). Actual endurance mileage varies depending on road conditions, temperature, wind velocity, humidity, personal weight, and operating habits. The endurance mileage value in this parameter page and the specification certificate are for reference only.

Maintenance & Repair

Regularly Check the E-bike:

• Check whether fasteners are locked and joints of various parts are normal.
• Check tire wear, cracks, and pressure (suggested: 35~45 psi). Ensure the drive system is smooth.
• Check whether the brake system is running properly.

E-bike Storage Method:

• If not using the product for a long time, do not store it outdoors, or under strong light, or below zero temperature. Keep it from heat sources (e.g., heating equipment) by at least 2cm.
• Store in a dry, clean, and well-ventilated indoor environment with a temperature of 10°C - 45°C and relative humidity not exceeding 90%.
• If not using the E-bike for a long time, charge it regularly (usually once every two months) to maintain battery performance.
• Keep the E-bike away from corrosive liquids and prevent it from mechanical shock and heavy object pressure.

Transportation:

• During transportation, prevent it from severe mechanical shock, exposure to sunlight, rain, chemical corrosive substances, and harmful gas erosion.
• During loading and unloading, handle it gently to prevent dropping, rolling, and heavy object pressure.

Instructions of Maintenance and Cleaning:

• It is forbidden to rinse the E-bike with water to avoid the hidden danger of accidents caused by soaking of internal electronic components and circuits.
• Gently wipe stains on paint or plastic parts with neutral detergent and a rag, then clean with a dry cloth.
• Wipe metal parts with lubricating oil for maintenance.
• It is strictly forbidden to inject oil into the brake part, as this can cause brake failure.

Authentication

EU Compliance Statement:

WEEE: Products must be disposed of and recycled properly. This sign indicates the product should not be disposed of with other domestic waste throughout the EU. Recycle to prevent harm to the environment and human health, and promote sustainable reuse of material resources. Use return and collection systems or contact the retailer for environmentally safe recycling.

EU Battery Recycling Information:

Batteries or battery compartments are marked in accordance with European Directive 2006/66/EC and amendment 2013/56/EU. The directive applies to the recycling framework of waste batteries and accumulator cells throughout the EU. The label on the battery indicates it should not be discarded but recycled at the end of its service life. The label may also contain chemical symbols of metals (Pb, Hg, Cd). Users should not dispose of batteries as garbage but use available collection frameworks. Minimizing potential impact on the environment and human health due to hazardous substances is important.

Restriction of Hazardous Substances (RoHS) Directive:

The products and parts (cables, wires, etc.) of Invanti (Beijing) Technology Co., Ltd comply with the requirements of Directive 2011/65/EU on restricting the use of certain hazardous substances in electrical and electronic equipment.

Trademark and Legal Statements

INVANTI and the INVANTI logo are trademarks of Invanti (Beijing) Technology Co., Ltd, used under license. The products are protected by relevant patent laws. This user manual describes all instructions and functions of the EB19 electric bicycle. With constant updates, the received EB19 may differ slightly from features shown. Invanti develops products with many functions and different models; some mentioned functions may not apply. The manufacturer reserves the right to change the design and function of the EB19 electric bicycle and documents without notice. © 2024 Invanti (Beijing) Technology Co., Ltd. All rights reserved.

Contact Us

If you encounter any problems when using the product, please contact us through the following methods: Amazon Platform: Contact Seller. Email Address: aftersales@invanti.com. A QR code is provided for scanning.