VEVOR Car Fridge Freezer Operating Manual
Model Information: This manual covers various VEVOR car fridge freezer models including A25/A30/A40/A50/A75/C25/C30/C40/C50/C75/C9/C12/C15, B15/C20/B20/CX30/CX40/CX50/CF8/NX42/NX52/NX62, CFC15/C22/B22/G22/MK18/MK25/MK35/K18/K25, C10, TW75D/TW95D, BT36/T50/T60, EBD45/BD60/BD75/BCD80/BCD100/BCD125, and GCF35/CF45/CF55/NCF35/NCF45/NCF55.
Safety Instructions
- Installation of DC power sources must be performed by qualified electricians.
- Ensure the power source voltage matches the socket.
- Allow the refrigerator to stand for at least six hours after unpacking before switching it on.
- Keep the refrigerator horizontal while operating. Maintain a tilt angle less than 5° for continuous operation and less than 45° for short periods.
- Ensure adequate ventilation around the refrigerator, with at least 200mm space at the back and 100mm at the sides for heat dissipation.
- Place the refrigerator away from heat sources and direct sunlight. Ensure it is stable and protected from rain and water immersion.
Troubleshooting
Refrigerator not working: Check power supply, plug and socket connection, fuse, and power switch. Note the 3-minute compressor delay protection upon switching on.
Food is frozen: The set temperature may be too low.
Water flowing sound: This is the normal sound of refrigerant flow.
Water drops on casing/door gap: This is normal condensation due to moisture in the air meeting the cold surface.
Slight compressor noise on startup: This is normal and will reduce as the compressor stabilizes.
Error Codes:
- F1: Low car voltage protection. Adjust battery protection setting (H to M or M to L).
- F2: Fan overload protection. Turn off for 30 minutes and restart.
- F3: Frequent compressor working protection. Turn off for 30 minutes and restart.
- F4: Compressor overload or low-speed operation. Turn off for 30 minutes and restart.
- F5: Overheated compressor module. Move to a ventilated area, turn off for 30 minutes, and restart.
- F6: Controller parameter detection failure. Restart the device. Contact support if the issue persists.
- F7 or F8: Temperature sensor error. Check the sensor terminal.
Operating Panel & APP
Panel Operations:
- Power Switch: Press to turn ON/OFF.
- Temperature Setting: Use '+' and '-' buttons.
- Mode Selection: Press 'Setting' to choose between ECO (Energy-saving) and MAX (Fast cooling). Factory default is MAX.
- Battery Protection: Long press the 'Setting' button for three seconds. When 'H' flashes, use the 'Setting' button again to cycle through H (High), M (Middle), and L (Low) protection modes. Factory default is H.
- APP Connection: For APP-enabled models, press the 'Setting' button after 'AP' is displayed on the panel to connect via Bluetooth.
APP Control: Download the VEVOR app from the App Store or Google Play. Enable Bluetooth and the app, then search for the fridge. The display panel will show 'AP' when ready for connection. Press the setting button on the fridge to connect.
Accessory Photos: Accessories may vary by model. Features like built-in batteries or portable battery options are subject to the specific model purchased. Built-in or portable batteries can power the fridge for approximately 4 hours.
Operating Description - Panel of different models
Model Group A & C (e.g., A25-C15)
- Press button to switch ON/OFF.
- Press '+' or '-' for temperature setting.
- Press 'Setting' to choose ECO or MAX mode. Factory setting is MAX.
- Long press for three seconds. When 'H' flashes, select battery protection mode (H/M/L) using the 'Setting' button. Factory setting is H.
- For APP models, press 'Setting' after 'AP' is displayed to connect via Bluetooth.
- CX series models: Handles and wheels can be removed.
- C series models: Dual doors require a cross screwdriver to adjust door direction.
Model Group B & C (e.g., CFC15-K25)
- Press button to switch ON/OFF. Long press for three seconds to unlock.
- Press '+' or '-' for temperature setting.
- Press 'Setting' to choose ECO or MAX mode. Factory setting is MAX.
- Long press for three seconds. When 'H' flashes, select battery protection mode (H/M/L) using the 'Setting' button. Factory setting is H.
- For APP models, press 'Setting' after 'AP' is displayed to connect via Bluetooth.
- Ice cube trays are equipped for C22/B22 models.
Model C10
- Press '+' or '-' to adjust temperature. The temperature display shows current temperature, unit (°C/°F), voltage, battery protection mode (H/M/L), battery power (%), and running mode (MAX/ECO).
- Press 'Cool/Stop' for 1 second to switch between cooling and standby modes.
- Press 'Hot/Stop' for 1 second to switch between heating and standby modes (if applicable). 'Cool/Stop' is disabled in heating mode, and vice versa. '+' and '-' are disabled in standby mode.
- In standby mode, long press '+' and '-' for 5 seconds to enter battery protection setting. Adjust using '+' or '-'.
- Cooling temperature range: -20°C to 20°C. Heating temperature range: +5°C to +20°C.
Model TW75D/TW95D
- Press '+' or '-' to adjust temperature. The temperature display will flash at 2Hz when entering temperature adjustment mode.
- Press '+' or '-' to adjust temperature. Holding the button allows for continuous adjustment at 4°C/second. The setting is confirmed if no button is pressed for 4 seconds.
- Press 'Cool/Stop' for 1 second to switch between cooling and standby modes.
- Press 'Hot/Stop' for 1 second to switch between heating and standby modes (if applicable).
- In standby mode, long press '+' and '-' for 5 seconds to enter battery protection setting. Adjust using '+' or '-'.
- Cooling temperature range: -20°C to 20°C. Heating temperature range: +5°C to +20°C.
Model BT36/T50/T60
- Long press button for three seconds to switch ON/OFF.
- Press '+' or '-' for temperature setting. The temperature of the left compartment should not be lower than the right.
- Press 'Setting' to choose ECO or MAX mode. Factory setting is MAX.
- When both compartments are active, press '+' or '-' to select left or right zone for temperature adjustment. Long press '+' or '-' for continuous adjustment.
- Long press '+' and '-' for three seconds simultaneously to turn the left zone ON/OFF. Similarly, long press and for the right zone. Both zones cannot be turned off simultaneously.
- Long press 'Setting' to enter parameter settings (E1 displayed). Press 'Setting' to cycle through E1-E2-E3...-EE. Adjust parameters using '+' or '-'. Long press '+' and '-' for three seconds to enter factory settings.
- The battery can be detached to adjust the inner space.
Model EBD45/BD60/BD75/BCD80/BCD100/BCD125
- Long press for three seconds. When 'H' flashes, select battery protection mode (H/M/L) using the 'Setting' button. Factory setting is H.
- For APP models, press 'Setting' after 'AP' is displayed to connect via Bluetooth.
- Icons under the screen indicate Left Zone (L-Box) and Right Zone (R-Box).
- Press upper '+' and '-' simultaneously for three seconds to switch the left zone ON/OFF.
- After removing the divider, the two zones merge, and temperature control is managed by the upper screen only.
- Press button to switch ON/OFF.
- Press '+' or '-' for temperature setting.
- Press 'Setting' to choose ECO or MAX mode. Factory setting is MAX.
- Long press for three seconds. When 'H' flashes, select battery protection mode (H/M/L) using the 'Setting' button. Factory setting is H.
Model GCF35/CF45/CF55/NCF35/NCF45/NCF55
- Press button to switch ON/OFF.
- Press '+' or '-' for temperature setting.
- Press 'Setting' to choose ECO or MAX mode. Factory setting is MAX.
- Long press for three seconds. When 'H' flashes, select battery protection mode (H/M/L) using the 'Setting' button. Factory setting is H.
Operating Method
- Power Source: DC 12/24V or AC 100-240V (with adaptor). DC 12/24V input is 12V for built-in battery models.
- Adaptor and Power Cord: Subject to specific model purchases.
- Battery Control Button (Built-in Battery Models): The battery function can be enabled or disabled based on voltage conditions.
Operating Manual
Mobile APP Control via Bluetooth (iOS & Android): Please read this operating manual carefully before using the device. Keep it in a safe place for future reference.
Car Fridge Freezer: This manual provides instructions for operating your VEVOR Car Fridge Freezer.