AKEEYO AKY-868GS

安全にお使いいただくために (Safety Precautions)

To ensure safe and effective use, please understand the following headings and use the product correctly.

Meaning of Headings:

• 警告 (Warning): Indicates content where incorrect handling could lead to death or severe injury.
• 注意 (Caution): Indicates content where incorrect handling could lead to injury or property damage.

Meaning of Symbols:

• ? This mark indicates prohibited actions.
• ✅ This mark indicates instructions to follow.

警告 (Warning)

• When using this product on roads, comply with local ordinances and prefectural traffic laws.
• Do not operate while riding a motorcycle or bicycle.
• Always stop in a safe location and confirm your surroundings before operating.
• Do not install in a location that obstructs vision or interferes with driving. This can cause accidents or injuries.
• Do not disassemble or modify the product. This can cause electric shock, fire, or burns.
• Do not insert metal objects, liquids, flammable materials, or chemicals into the product. This can cause short circuits and fire.
• If liquid leaks from the battery pack, wash it off with clean water immediately. If it gets into your eyes or on your skin, seek medical attention from an ophthalmologist or dermatologist. Also, if there is residual liquid inside the product, consult the retailer where you purchased it.

注意 (Caution)

• If you notice any unusual odor or sound from the product, stop using it immediately. Continuing to use it may cause short circuits and fire.
• Avoid charging or leaving the product in high temperature and humidity environments. This may cause overheating, rupture, ignition, electric shock, deformation, or malfunction.
• The product can be used in places where it may get wet, but caution is required. The waterproof rating is IP65 compliant, but it is not completely waterproof.
• When disposing of the product, follow local ordinances. Please contact your local municipality for details.

同梱物確認 (Package Contents)

Before using the unit, please confirm all included items.

• Drive Recorder Unit x1
• Camera x2
• Remote Control x1
• Main Unit Mounting Bracket x1
• Camera Mounting Bracket x2
• Mount x1
• Constant Power Cable x1
• USB Power Cable x1
• Cable Ties
• microSD Card
• Manual x1

Note: Specifications and appearance are subject to change without notice due to improvements. Images and illustrations are for representative purposes only; actual products may differ.

各部名称説明 (Part Names)

1. Power / LCD On/Off Button:

• Power On/Off: Press and hold for approx. 3 seconds.
• LCD On/Off: Short press to turn LCD off while it's on; press again to turn it back on.

2. LCD Panel (3-inch):

❗ Caution: This is not a touch panel. Do not press the screen.

3. Reset Button:

Use a thin object like a toothpick to press the reset button to restart the device.

4. microSD Card Slot:

• Supports microSD cards from 16GB to 128GB (Class10 or higher recommended).
• ❗ Caution: Please refer to page 5 for microSD card usage and precautions.

5. Unit Operation Indicator Lamp:

• Recording: Blue flashing ✨
• Recording Stopped: Blue solid ⚫
• Charging: Red solid ⚡
• Fully Charged: Red off ⚪ (May show red and blue simultaneously depending on the situation.)

6. MENU / SOS Emergency Recording Button:

• While stopped: Short press to switch between settings menu / recording modes.
• While recording: Short press to start SOS emergency recording.
• During SOS recording: Press and hold for approx. 3 seconds to stop SOS recording.

7. Screen Display Mode Switch / Cursor (Previous):

• Recording Mode: Short press to switch between front and rear camera display modes. The order is: <1> Front, <2> Rear, <3> Front, <4> Rear, <5> Front+Rear (Wipe).
• Playback Mode: Short press to move the cursor forward.
• Settings Menu: Short press to move the cursor forward.

Note: After turning off the unit, the display will return to the <1> Front+Rear (Wipe) view upon the next power-on.

8. Record / OK Button:

• Recording Mode: Short press to start/stop recording.
• Settings Menu: Press to select an item or confirm a setting.
• Playback Mode: Press to play/pause a video.

9. Microphone On/Off / Cursor (Next):

• Recording Mode: Short press to toggle microphone (recording) on/off.
• Playback Mode: Short press to move the cursor forward. Press and hold for approx. 3 seconds to enter playback settings menu. Press and hold again for approx. 3 seconds to exit.
• Settings Menu: Short press to move the cursor forward.

10. MODE / Delete Button:

• While stopped: Short press to switch between recording and playback modes.
• Playback Mode: Press and hold for approx. 3 seconds to delete a file.
• Settings Menu: Short press to switch between recording and playback modes.

11. Microphone:

Records ambient sound. Recording is not possible when the remote control is not connected.

12. Recording Indicator Lamp:

• Recording: Blue flashing ✨
• Recording Stopped: Blue solid ⚫

13. Screenshot / SOS Emergency Recording Button:

• While recording: Short press to start SOS emergency recording.
• During SOS recording: Press and hold for approx. 3 seconds to stop SOS recording.

micro SDカードについて (About micro SD Card)

対応可能micro SDカード (Supported micro SD Cards)

Do not use micro SD cards other than those specified below. Doing so may result in data corruption or inability to record.

• Use micro SD cards with a capacity of 16GB to 128GB.
• Use cards with a speed of "Class10 UHS-I" or higher. Using cards below Class10 may result in recording failures.
• Format the card on your PC using FAT32 format before use. ❗ Caution: Formatting the card will erase all recorded data. Back up your data beforehand.
• In the event of an accident, to ensure the moment of the accident is recorded, turn off the power and remove the micro SD card immediately.

『カードの差し込み&取り出す』 (Inserting & Removing the Card)

Inserting the Card:

With the unit powered off, insert the card while checking its orientation. Insert it until you hear a click.

Removing the Card:

With the unit powered off, push the card in until you hear a click, then pull it out to remove it.

警告 (Warning)

1. Do not remove your finger until the card is fully inserted.
2. Format the card periodically (recommended once a month).
3. Removing or inserting the card while the power is on may cause data corruption or damage to the unit.

接続方法 (Connection Method)

(1)接続図 (Connection Diagram)

This section describes how to connect the cameras, remote control, and power cable to the drive recorder unit. The diagram shows the unit with ports labeled for Camera B, Camera A, Remote, and Power.

The constant power cable has a red wire (ACC) and a black wire (GND).

(2)電源ケーブルについて (About Power Cables)

USB Test Power Cable

Before installing on your motorcycle, you can use the included USB power cable to check if the unit operates normally. It can be connected to a motorcycle's USB port, a home AC adapter, or a mobile battery.

(Images of motorcycle USB socket, mobile battery, and AC adapter are described here, all rated 5V 2.0A, sold separately.)

❗ Caution: The AC adapter or mobile battery must have an output of 5V/2.0A and be PSE certified for testing. Insufficient voltage or current, or low battery on a mobile battery, may prevent normal startup or cause display abnormalities. These are not product defects.

オートバイ専用常時電源ケーブル (Motorcycle Dedicated Constant Power Cable)

Red Wire (ACC): Connect to either:

• Accessory power (+)
• A wire that receives 12V when the ignition key is ON.

Black Wire (GND): Connect to ground.

❗ Caution: Before connecting wires, confirm how to access accessory power (ACC). Using a tester is recommended. Incorrect power connections may prevent engine synchronization, cause the unit to not turn on, or stop recording. Contact the service center if this occurs. Poor wire connections may cause the unit to turn off while riding or prevent recording.

(3)オートバイへの接続イメージ (Connection Image to Motorcycle)

The diagram illustrates the typical installation on a motorcycle:

• The Drive Recorder Unit (not waterproof) is installed under the seat or in a storage space.
• The Rear Camera (waterproof) is mounted at the rear.
• The Front Camera (waterproof) is mounted at the front.
• The Remote Control (splashproof) is mounted on the handlebar for operation.
• The Power Cable connects these components.

❗ Caution:

1. The diagram is for illustrative purposes; actual installation may vary by motorcycle model.
2. Cameras are IP67 waterproof.
3. The Drive Recorder Unit is not waterproof. Install it in a location protected from water.
4. The remote control is splashproof, making handlebar mounting possible.

ご使用の前に (Before Use)

(1)カメラの取り付け (Camera Installation)

1. Fixing Ring: Attach to the front of the camera. The camera body and fixing ring can rotate 360 degrees depending on the mounting position.

2. Fixing Screw: Use a commercial Phillips head screwdriver to tighten or loosen the fixing screw and the bracket. ❗ Caution: Loosening the screw allows adjustment of the camera's tilt angle. Be aware of the different shapes of screw tips.

3. Camera Mounting Bracket: Made of metal, can be bent if necessary to mount on curved cowlings.

❗ Caution: The bracket should be fixed to the left side, not the center of the fixing ring. Please be careful!

4. Double-sided Tape: Peel off the protective film from the double-sided tape and stick it to the desired mounting location.

❗ Caution: Clean the mounting surface thoroughly of water, oil, and dust before applying. Reusing the tape may weaken adhesion and cause the camera to detach. Ensure the mounting location is suitable for the camera before applying the tape. The camera body is waterproof (IP67). Wipe off dirt with a soft cloth. It is normal for the image to appear wavy during acceleration due to the CMOS sensor's specifications; this is not a defect. Please understand this.

5. Installation Complete Diagram: (Shows an assembled camera unit)

(2)ドライブレコーダー本体の取り付け (Drive Recorder Unit Installation)

Recommended: Install under the seat or in a storage space.

❗ Caution: The drive recorder unit is not waterproof. Install it in a location protected from water.

For installation in a location visible while riding:

(Diagrams show mounting options for the unit.)

(3)ケーブル接続の注意点 (Cable Connection Precautions)

When connecting connectors, pay attention to connector color, male/female pins, and pin count/orientation!

⚠️ Warning: Confirm the pin count and orientation before inserting fully.

(Diagram shows correct and incorrect connections.)

(4)電源オン・オフ (Power On/Off)

Press and hold the power button for approximately 3 seconds to turn the unit on or off.

Auto Recording: If "Auto Recording" is set to "ON" in the settings menu, the unit's recording will synchronize with the motorcycle's engine ON/OFF.

Delayed Power Off: If "Power Off Delay" is set to "3 sec / 5 sec / 10 sec" in the settings menu, the unit will continue to operate using its internal battery for the set duration after the engine is turned off.

(5)日付と時刻設定 (Date and Time Setting)

Manual date and time setting is necessary to display correct timestamps on recorded footage.

Setting Procedure:

1. Power ON → Stop Recording (OK Button) → MENU (Menu Button) → [Date Setting].
2. Use the cursor buttons (▲▼) to adjust each number.
3. Use the MENU button to move to the next date/time item.
4. Use the OK button to finalize the setting.

Note: If the internal battery depletes, the unit is reset, or initialized, you will need to set the date and time again.

(6)液晶画面の切替 (LCD Screen Switching)

You can switch the camera display on the LCD. In recording mode, short press the cursor (▲) button to cycle through the 2-camera display modes.

(Diagrams show different screen layouts: <1> Front, <2> Rear, <3> Front, <4> Rear, <5> Front+Rear (Wipe).)

Note: Screen settings are reset when the power is turned off and are not saved.

録画中の液晶画面 (LCD Screen During Recording)

The LCD screen displays various information during recording:

• Recording Time: Displays the current recording duration.
• Recording Mode: Indicates the current recording mode (e.g., Loop, Emergency).
• Loop Time: Shows the duration of each loop recording segment.
• G-Sensor Sensitivity: Indicates the sensitivity level of the G-sensor.
• Lock Icon: Appears when a file is protected (e.g., SOS recording).
• A Camera: Displays the feed from Camera A.
• Microphone Icon: Indicates if the microphone is active.
• B Camera: Displays the feed from Camera B.
• Card Icon: Shows the status of the microSD card.
• Battery Status: Indicates the battery level.

Note ①: An icon appears when emergency recording starts.

Note ②: The set date and time are displayed. Please refer to page 13 for Date and Time settings.

録画形式 (Recording Format)

ループ録画/自動上書き録画 (Loop Recording / Automatic Overwrite Recording)

• The unit continuously records from engine start (ACC ON) until engine stop (ACC OFF).
• Videos are saved in segments of 1, 2, or 3 minutes, depending on the setting.
• When the card capacity is full, the oldest files are automatically overwritten.
• (Diagram shows file saving sequence.)

緊急録画 (Emergency Recording)

● 緊急録画 (衝撃感知録画) (Emergency Recording - Impact Detection Recording)

When the G-sensor detects an impact during normal recording, emergency recording automatically starts. The recorded video file is protected (locked).

Note: If G-sensor sensitivity is set to OFF, impact detection recording will not start.

● 【手動緊急録画】 (Manual Emergency Recording)

During normal recording, press the emergency recording button 【△】 on the remote control to start emergency recording.

Video files recorded by impact detection and manual emergency recording are saved in the [SOS] folder on the microSD card.

緊急録画の保存ファイルについて (About SOS Recording File Storage)

When the G-sensor detects an impact during recording of Video ②, that video file (Video ②) is saved in the [SOS] folder. Since both front and rear cameras record simultaneously, two video files are saved in total.

❗ Caution:

• SOS recorded data is saved in the [SOS] folder on the microSD card and will be overwritten automatically.
• It is recommended to set the loop recording time to 1 minute.

録画した映像の再生 (Playback Recorded Video)

本機で再生 (Playback on Unit)

When the unit is stopped, press the MODE button to enter playback mode.

You can perform the following operations in the playback file list:

• Press the OK button to play/pause the video.
• Press the cursor buttons (◀/▶) to switch between previous/next files.
• Press and hold the MODE button for approximately 3 seconds to delete files.

動画ファイル名の説明 (Video File Name Explanation)

Example: 1122_121322A_SOS(26/150)

• 1122_121322A: Video Recording Date and Time.
• SOS: Indicates that the G-sensor detected an impact or the emergency recording button was pressed. Files with "SOS" in the name are not overwritten and cannot be deleted from the unit. Deletion requires PC operation.
• (26/150): File number (e.g., 26th file out of 150 total).
• Camera Display: A=Camera ①, B=Camera ②.
• Total Files Recorded: Indicates the total number of files recorded.
• Total Recordable Files: Indicates the total number of files that can be recorded.

PCで再生 (Playback on PC)

Insert the microSD card used for recording into a card reader (sold separately) and connect it to your PC to play back recorded videos and still images.

1. Connect the microSD card to your PC.
2. Open the video folder. Inside, you will find subfolders: SOS, VIDA, and VIDB.
• SOS: Contains emergency recording files (front + rear camera simultaneous recording).
• VIDA: Contains normal recording videos from Camera A.
• VIDB: Contains normal recording videos from Camera B.

動画ファイルをPCで再生できる対応OS (Supported OS for Playing Video Files on PC)

• Windows: Windows 8/10 (32bit/64bit). Windows Media Player version 10 or later is recommended.
• Mac: Mac OSX 10.3.6 or later. QuickTime version 6.5 or later is recommended.

Note: Playback performance may vary depending on your PC's processing power. Not all PCs may be able to play back files correctly or operate as expected. The manufacturer does not guarantee operation on all PCs.

設定メニュー (Settings Menu)

Press the ME button when the unit is not recording to display the settings menu.

1. Recording Resolution: 1080P/49fps
2. Loop Recording: 1 min (★) / 3 min / 5 min (1 min is recommended!)
3. B Camera Mirror Image Setting: Mirror Image (★) / Normal Image
4. G-Sensor Sensitivity: ON (★) / OFF
5. Beep Sound: High / Medium (★) / Low
6. Exposure Compensation: -3 / -2 / -1 (★) / 0 / 1 / 2 / 3
7. Auto Recording Setting: ON (★) / OFF. ❗ Caution: If set to OFF, you must start recording manually!
8. Screen Off Timer: 10 sec / 20 sec / 30 sec (★) / Do not turn off
9. Microphone Setting: ON (★) / OFF
10. Date/Time Setting: Sets the system time of the unit.
11. Language Setting: Japanese (★) / Simplified Chinese / Traditional Chinese / English / Korean
12. Flickerless: 50Hz / 60Hz (★)
13. Power Off Delay: 3 sec (★) / 5 sec / 10 sec
14. Format: Formats the card.
15. Initialize: Resets all settings to factory defaults.
16. Memory Card Capacity: Displays the capacity of the microSD card.
17. Card Test: Tests the compatibility of the microSD card. ❗ Caution: Running the test will erase all data on the card. Please be careful!
18. Version Number: Displays the firmware version.

Items marked with (★) are the factory default settings. Resetting to factory defaults will restore all settings to these initial values. Please be aware of this.

トラブルシューティング (Troubleshooting)

If you encounter any issues during use, please try the following steps. If the problem persists, contact the service center.

仕様書 (Specifications)

Note: Specifications are subject to change without notice due to product improvements. For additional purchases of accessories or replacement parts, please contact the retailer where you purchased the product.

保証について (Warranty Information)

【免責事項】 (Disclaimer)

• When using this product on roads, comply with local ordinances and prefectural traffic laws. The user is solely responsible for legal compliance; the manufacturer, importer, and retailer are not liable for any legal responsibilities.
• The warranty covers only the main unit of the product. The company is not responsible for data loss, corruption, or any other damages incurred due to product malfunction or use.
• The use of our products or any defects/malfunctions that cause accidents, injuries, loss of time or profit, or any other disadvantages are not the responsibility of the company.
• Filming or photographing with this product is for personal enjoyment only. Unauthorized use, reproduction, broadcasting, rental, or use of individuals' likeness without consent, or any actions that cause significant nuisance to the public (e.g., posting on SNS) are prohibited and not the responsibility of the company.
• This product does not guarantee recording under all circumstances.
• The company is not responsible for any damages resulting from malfunctions, use, or damage to recorded images or data.
• Filmed images are not guaranteed as evidence in accidents.
• Install the product correctly according to the instruction manual. To comply with safety standards for road vehicles, install it in a location that does not obstruct driving or vision.
• LED traffic signals may appear to flash or their colors may not be distinguishable. The company is not responsible for issues related to traffic signal recognition or recording.

The following situations are not covered by the warranty:

• Use of a disassembled or modified battery. (Disassembling or modifying a battery can cause rupture or leakage.)
• Deterioration of the battery. (Batteries are consumable items.)
• Malfunctions or damage caused by fire, earthquake, flood, lightning, natural disasters, pollution, corrosive gases (e.g., sulfuric gas), or abnormal voltage.

【製品保証】 (Product Warranty)

The product warranty period is 1 year from the date of purchase for the main unit (accessories are covered for 30 days). However, malfunctions or defects caused by user misuse may not be covered. Please refer to the "Safety Precautions" section of this manual. Please inspect the product within 30 days of purchase. If a defect is confirmed within 30 days, please return the product via cash-on-delivery using our designated shipping carrier. After 30 days, repairs will be handled as warranty repairs. Shipping costs for repairs after 30 days must be borne by the customer. Return shipping costs for exchanges and repairs will be covered by the company.

サポートセンター (Support Center)

Contact: Support Center
TEL: 048-888-0217
Email: jphelp@akeeyo.com
Hours: 9:30 - 19:00 (Closed: Saturdays, Sundays, National Holidays, Year-end/New Year holidays)

返品同梱説明書 (Return/Exchange Instructions)

In case of returns or repairs, please fill out the following information and include it with the returned item.

AKY-868GS Return / Exchange / Refund Instructions

For prompt processing of returns, please include this document with your return.

1. Please select the service you require:
• Refund [ ]
• Repair [ ]
• Exchange [ ]
2. Please provide your order number:
• Amazon Order Number: 000-000000-0000000
• For purchases made through channels other than Amazon, please specify the purchase method and store name.
3. Contact Information:
1. Date of Purchase: Year ____ Month ____ Day ____
2. Reason for Return: (Describe the situation and the nature of the defect)
4. Emergency Contact Method:

(For inquiries during repair/exchange process)

1. Please specify your preferred contact method:
2. Phone Number:
3. Email Address:
5. Return Shipping Address: (Recipient + Postal Code + Address + Phone Number)
6. Other: (If you have any other questions or requests, please feel free to write them here.)