Odokee H03 All-in-One Sleep-Wake Solution

Getting Started

Plug the adapter into a standard household outlet. The display will show 12:00 AM, indicating the clock is ready to be set.

Insert 2 "AAA" batteries (not included) into the bottom of the clock to preserve settings during power interruptions. Follow the polarity diagram in the battery compartment.

Notice:

• Bluetooth will automatically turn off if it fails to connect to your phone within 5 minutes.
• Bluetooth music playback will pause if you receive a call.
• Keep your clock and phone within 10 meters (33 ft) of each other for optimal Bluetooth connection.

Time Setting

Follow these steps to set the time:

1. Press the 'TIME' button to enter HOUR setting. The HOUR digits will flash.
2. Press '+' or '-' to advance to the correct hour. Hold for rapid setting.
3. Press 'TIME' again to confirm and enter MINUTE setting. The MINUTE digits will flash.
4. Press '+' or '-' to advance to the correct minute. Hold for rapid setting.
5. Press 'TIME' a third time to confirm and enter TIME FORMAT (12/24HR) setting. "12H" will flash, indicating 12-hour mode (regular time).
6. Press '+' or '-' to select the time format. "24H" will flash, indicating 24-hour mode (military time).
7. Press 'TIME' a fourth time to confirm and exit time setting mode.

Notice:

• The clock will exit time setting mode automatically if no action is taken within 8 seconds.
• In 12-hour format, the AM icon appears from 12:00 midnight to 11:59 AM. The PM icon appears from 12:00 noon to 11:59 PM.
• In regular time, AM or PM will display. Otherwise, the clock is in Military Time.

Brightness Control

Adjust the LED display brightness from 0-100% using the 'DISPLAY DIMMER' knob on the left side of the clock.

Notice:

• If the display is blank after plugging in, ensure the 'DISPLAY DIMMER' knob is set to a higher position.
• Under battery power, the display may go blank, and the preset alarm may not sound.

Turning Alarm On/Off

In non-setting mode, press the 'ALARM' button to turn the alarm on or off. The alarm icon will appear when the alarm is on.

Bluetooth Connection Setting

To turn Bluetooth on/off: Press the 'BT' button. The 'BT' icon will flash on the display when Bluetooth is on.

To connect:

1. Turn on Bluetooth on your phone and connect to the device named "H03". The 'BT' icon will stop flashing upon successful connection.
2. Press and hold the 'BT' button for 2 seconds to turn off Bluetooth when connected.

Music playback:

• Press '+' or '-' to change tracks.
• Press 'BT' to pause music and again to play.
• Press '+' or '-' to adjust volume from 01 to 32. The default volume is 16.

Alarm Time Setting

Follow these steps to set the alarm time:

1. Press the 'ALARM' button to enter ALARM HOUR setting. The HOUR digits will flash.
2. Press '+' or '-' to advance to the correct hour. Hold for rapid setting.
3. Press 'ALARM' again to confirm and enter ALARM MINUTE setting. The MINUTE digits will flash.
4. Press '+' or '-' to advance to the correct minute. Hold for rapid setting.
5. Press 'ALARM' a third time to confirm and exit alarm setting mode.

Alarm Sound & Volume Setting

1. Slide the control on the right side to the 'ALARM SOUND' position to enter alarm sound mode. The display will stop flashing.
2. Press '+' or '-' to select one of seven built-in alarm sounds (01-Birds Chirping, 02-Piano, 03-Flute, 04-Forest, 05-Wave, 06-Beep, 07-Buzzer). The selected alarm sound will play.
3. Slide the control to the 'ALARM VOLUME' position to enter alarm volume setting. The alarm volume options will flash.
4. Press '+' or '-' to adjust the alarm volume from 01 to 32. The default alarm volume is 16.
5. Slide the control to the 'LOCK' position to confirm and exit setting mode.

Sunrise Brightness & Duration Setting

1. Slide the control to the 'SUNRISE BRIGHTNESS' position to enter sunrise brightness setting. The options will flash.
2. Press '+' or '-' to adjust sunrise brightness from 01 to 30. The default is 15.
3. Slide the control to the 'SUNRISE DURATION' position to enter sunrise duration setting. The options will flash.
4. Press '+' or '-' to adjust sunrise duration from 05 to 60 minutes. The default is 30 minutes.
5. Slide the control to the 'LOCK' position to confirm and exit setting mode.

Notice: The sunrise light gradually illuminates before the alarm time (default 30 minutes). At the set alarm time, the light reaches the preset brightness level.

Example: For a 6:30 AM alarm, the sunrise begins at 6:00 AM.

Sleep Sound Setting

1. Press the 'SLEEP SOUND' button to turn sleep sounds on/off.
2. When sleep sound is on, press '+' or '-' to choose from 25 sleep sounds (S01-S25).
3. Press '+' or '-' to adjust the volume from 01 to 32 levels.

Track List: Lullaby 1, Birds Chirping, Ocean Wave, Shush, Heartbeat, Rain, Thunderstorm, Brook, Cricket Chirping, Train, Forest, Wind, Lullaby 2, Yoga, Meditation, White Noise 1, White Noise 2, Space White Noise, Pink Noise, Brown Noise, Blue Noise, Fan 1, Fan 2, Fan 3, Fan 4.

Sleep Timer Setting

The sleep timer allows you to fall asleep with sleep sound, Bluetooth, or the nightlight, which will automatically turn off after the set duration.

1. When sleep sound, Bluetooth, or nightlight is on, press the 'TIMER' button repeatedly to select a duration: 30, 60, 90, 120, 180, or 240 minutes. The sleep timer indicator will appear on the display.
2. Wait 5 seconds for the setup to complete.
3. To turn off the sleep timer, press the 'TIMER' button repeatedly until "OFF" is displayed, then wait 5 seconds to exit.
4. When the sleep timer is active, press the 'TIMER' button to view the remaining time.

Notice:

• Press and hold the 'TIMER' button for 2 seconds to turn off the sleep timer. It will default to the last selected duration when reopened.
• If both the nightlight and sleep sound/Bluetooth are on, the sleep timer applies to both.

Alarm Mode Setting

Slide the control on the left side of the clock to your desired position:

• LIGHT: Wake up with light ONLY.
• SOUND: Wake up with sound ONLY.
• SOUND+LIGHT: Wake up with both sound and light.

Notice: The default alarm mode is "SOUND+LIGHT".

Snooze / Turn Off Alarm Daily

• When the alarm sounds, press the 'SNOOZE' button for a 9-minute delay. The alarm will sound again later.
• To cancel the snooze or turn off the alarm for the day while it is sounding, press the 'ALARM' button. The alarm will sound again at the same time the next day.
• If the alarm is not stopped, it will sound for 30 minutes before silencing automatically.

Notice:

• In 'LIGHT' alarm mode, snoozing turns off the sunrise light temporarily; it will relight to the preset brightness after 9 minutes.
• In 'SOUND+LIGHT' alarm mode, snoozing keeps the sunrise light on until the alarm is manually turned off for the day.

Night Light Setting

1. In normal time display mode, press the 'SNOOZE' button to turn on the night light.
2. Press the 'SNOOZE' button repeatedly to cycle through 12 color options: sunrise, red, orange, yellow, green, indigo, blue, purple, sunset, loop color, RGB 1, RGB 2.
3. Slide the 'NIGHTLIGHT DIMMER' on the right side to adjust brightness from 10% to 100%.
4. Press and hold the 'SNOOZE' button for 2 seconds to turn off the night light.

Notice: The night light will default to the last chosen color when turned on again.

Specifications

• Power Input: DC 5V/2.0A
• Power: AC, 100-240V (50/60Hz)
• Speaker Output: 5 Watt RMS

Troubleshooting

1. Bluetooth Connection Issues:
   • Ensure the device is not paired with other devices.
   • Forget all Bluetooth pairing records on your device.
   • Reset the clock by unplugging it and removing the battery, then power cycle.
   • Disable and re-enable Bluetooth on your device.
   • Try connecting to another device.
   • Contact customer support if issues persist.
2. Alarm Not Going Off:
   • Verify the alarm is set to the correct AM/PM time.
   • Ensure the alarm is turned on (alarm icon visible).
   • Check that the alarm mode is set to 'SOUND' or 'SOUND+LIGHT'.
   • Contact customer support for assistance.
3. Display Not Lighting Up:
   • Check power connections for looseness.
   • Try a different power outlet.
   • Adjust the 'DISPLAY DIMMER' knob to a higher setting.
   • Contact customer support if the problem continues.
4. Display Flashing Continuously:
   • Ensure the control on the right side is slid to the 'LOCK' position.
   • Contact customer support for help.
5. Turning Off Alarm Daily:

   Pressing the 'ALARM' button when the alarm sounds will turn it off until the next scheduled time.

   Contact customer support for further assistance.

6. Turning Off Alarm Completely:

   In normal time display mode, press the 'ALARM' button once to turn the alarm off completely. The alarm icon will disappear.

   Contact customer support for help.

Warranty & Support

Odokee offers a 45-day money-back guarantee and an 18-month free replacement warranty.

For assistance, please have your model number and order ID ready and contact Odokee customer support via email at support@odokeeshop.com.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement and can be used in portable exposure condition without restriction.