Hilti HIT-ICE Adhesive Anchoring System

Hilti is a registered trademark of Hilti Corporation, Schaan, Liechtenstein

Product Overview

The Hilti HIT-ICE is a high-performance chemical anchoring system designed for secure fastenings in concrete. It is suitable for various applications including rebar and anchor fastenings.

Hazard Information

WARNING

Contains: dibenzoyl peroxide(B), hydroxypropylmethacrylate(A)

? Heating may cause a fire. (B) | ❗ May cause an allergic skin reaction. (A,B) | Causes serious eye irritation. (A,B) | Very toxic to aquatic life with long lasting effects. (B) | Harmful to aquatic life with long lasting effects. (A)

Keep away from heat/sparks/open flames/hot surfaces – No smoking. Do not get in eyes, on skin, or on clothing. Wear protective gloves/protective clothing/eye protection.

UFI: 6VVQ-V0D8-HX01-ACGC (A) | UFI: WJ5R-003C-FX00-5UAV (B)

Technical Specifications

Temperature Guidelines

Temperature (°F)	Temperature (°C)	Working Time (t_work)	Curing Time (t_cure)
-10	-23	1.5 h	36 h
0	-18	1.5 h	24 h
20	-7	1 h	6 h
40	4	15 min	1.5 h
60	16	5 min	1 h
70	21	2.5 min	45 min
90	32	1 min	35 min

Note: t_cure is approximately 2 x t_work.

Anchor Systems & Dimensions

The system is available for different anchor types:

Rebar
HIS-N
HAS(-U) / HIT-V

Fractional/Imperial Units

US Rebar	CA Rebar	HIS-N, -RN			HAS(-U) / HIT-V
d₀ [inch]	d [inch]	h_ef [mm]	d [inch]	h_ef [inch]	d_f [inch]	h_s [inch]	T_inst [lb-ft]	d [inch]	h_ef [inch]	h_ef [inch]	d_f1 [inch]	d_f2 [inch]	T_inst [Nm]	T_inst [lb-ft]
7/16
1/2	#3	2 3/8...7 1/2
9/16		10 M	60...226
5/8	#4	2 3/8...10
11/16
3/4	#5	3...12 1/2	15 M	80...320	3/8	4 3/8	7/16	3/8...15/16	≤15	5	3 1/8...12	1/2	13/16*	11/16	≤60	≤80
7/8	#6	3...15			1/2	5	9/16	1/2...13/16	≤30	3/4	6 5/8	3 1/2...15	15/16*	13/16	≤100	≤136
1	#7	3 1/3...17 1/2	20 M	90...390						7/8		3 1/2...17 1/2	1 1/8*	15/16	≤125	≤169
1 1/8	#8	4...20			5/8	6 3/4	11/16	5/8...11/2	≤60	1		4...20	1 1/4*	1 1/8	≤150	≤203
1 1/4	#8	4...20	25 M	101...504	3/4	8 1/8	13/16	3/4...17/8	≤100	1 1/4		5...25	1 1/2*	1 3/8	≤200	≤271
1 3/8	#9	4 1/2...22 5/8	30 M	120...598
1 1/2	#10	5...25
1 3/4	#11	5 1/2...27 1/2

Metric Values

	EU Rebar	HIS-N, -RN			HAS(-U) / HIT-V
d₀ [mm]	d [mm]	h_ef [mm]	d [mm]	h_ef [mm]	d_f [mm]	h_s [mm]	T_inst [Nm]	d [mm]	h_ef [mm]	d_f1 [mm]	d_f2 [mm]	T_inst [Nm]
10	8	60...160	M8	60...160	11	10	≤10
12	10	60...160	M10	60...200	14	12	≤20
14	12	60...200	M8	90	9	8...20	≤10	M12	70...240	16	14	≤40
16	12	70...240	M10	110	12	10...25	≤20	M16	80...320	20*	18	≤80
18	14	75...280
20	16	80...320	M12	125	14	12...30	≤40	M20	90...400	24*	22	≤150
22
25	20	90...400	M16	170	18	16...40	≤80	M24	96...480	30*	28	≤200
28			M20	205	22	20...50	≤150
32	25	100...500

Accessories

The system utilizes various accessories for installation:

HIT-RB: Brush for borehole cleaning (hef > 20 x d)
HIT-SZ: Overhead application accessory
HIT-DL: Cleaning rod (hef > 10 inches / 250 mm)
HIT-OHC: Nozzle
HIT-M2: Mixer (supplied with the product)
HIT-OHW: Dispensing tool

Ancillary Equipment

For effective use, the following equipment may be required:

Hilti VC 150/300 or VC 20/40 (-Y) vacuum cleaner (for dust extraction)
MD 1000 (possibly a dispensing tool or accessory)
Art. No. 381215 (related to drilling/dispensing, requires ≥ 6 bar / 90 psi air supply)

Installation Guide

Follow these general steps for proper installation:

Borehole Preparation: Drill the borehole to the specified diameter and depth (hef). Ensure the borehole is clean and free from debris, dust, water, oil, and grease. Use Hilti TE-CD or TE-YD hollow drill bits with a Hilti vacuum cleaner for dust extraction. Brush the borehole with a suitable steel brush, ensuring resistance is felt to confirm correct brush size.
Anchor Insertion: Insert the anchor or rebar into the prepared borehole. Ensure it is seated correctly.
Adhesive Dispensing: Attach the correct mixer (HIT-M2) to the cartridge. Dispense the adhesive from the bottom of the borehole to avoid air voids. Use extensions if necessary to reach the bottom.
Curing: Allow the adhesive to cure for the specified time (t_cure) based on the ambient and base material temperatures. The working time (t_work) is also critical.

Important Considerations:

Ensure correct cartridge and base material temperatures are maintained during installation (typically -23°C to 32°C / -10°F to 90°F).
Store and transport the product in a cool, dry, dark place between 5°C and 25°C (41°F and 77°F).
Partially used cartridges must be used within four weeks. Leave the mixer attached and store according to recommendations.
For overhead applications, use the HIT-SZ accessory and exercise caution.
In water-saturated concrete, the anchor must be set immediately after borehole cleaning.

Safety and Handling Precautions

Always wear appropriate Personal Protective Equipment (PPE): safety glasses, gloves, and protective clothing.
Never start dispensing without a mixer properly screwed on.
Always attach a new mixer before dispensing from a new cartridge.
Do not modify the mixer or use damaged cartridges.
Improper handling can cause mortar splashes.
Ensure adequate borehole cleaning for optimal adhesion and to prevent fastening failure.
Failure to adhere to instructions can result in fastening failure.

Disposal Information

Dispose of empty and partially used cartridges as special waste in accordance with official regulations and local EAK waste codes.

	Hilti HIT-RE 100 Adhesive Anchoring System: Instructions for Use and Technical Data Comprehensive instructions and technical specifications for the Hilti HIT-RE 100 adhesive anchoring system, covering rebar and anchor fastenings in concrete. Includes safety information, application guidelines, and accessory compatibility.
	Hilti HIT-RE 500 V3 1400 Jumbo Adhesive Anchoring System: Instructions for Use and Safety This document provides comprehensive instructions, safety precautions, and technical specifications for the Hilti HIT-RE 500 V3 1400 Jumbo adhesive anchoring system. It is designed for secure rebar and anchor fastenings in concrete, detailing chemical composition, hazard warnings, handling procedures, and application guidelines for professional use.
	Hilti HIT-HY 150 MAX-SD / 1400 Jumbo Adhesive Anchoring System: Installation and Safety Guide Comprehensive guide for the Hilti HIT-HY 150 MAX-SD / 1400 Jumbo adhesive anchoring system, detailing installation procedures, safety precautions, technical specifications, compatibility charts for rebar and threaded rods, and curing times for concrete fastenings.
	Hilti HIT-HY 100 Adhesive Anchoring System for Rebar and Anchor Fastenings in Concrete Comprehensive guide to the Hilti HIT-HY 100 adhesive anchoring system for rebar and anchor fastenings in concrete, covering safety instructions, product information, and application details.
	Hilti HIT-HY 200-A Adhesive Anchoring System for Rebar and Anchor Fastenings in Concrete Comprehensive guide to the Hilti HIT-HY 200-A, an adhesive anchoring system for rebar and anchor fastenings in concrete. This document details product information, safety warnings, installation instructions, and disposal considerations.
	Hilti HIT-HY 200-A/R V3 Adhesive Anchoring System: Installation and Safety Guide Comprehensive guide for Hilti HIT-HY 200-A V3 and HIT-HY 200-R V3 adhesive anchoring systems, covering installation, technical specifications, safety precautions, and usage instructions for rebar and anchor fastenings in concrete.
	Hilti HIT-HY 200-A V3 Operating Instructions and Technical Data Comprehensive operating instructions and technical data for the Hilti HIT-HY 200-A V3 adhesive mortar system, detailing application, safety, and performance specifications for concrete anchoring.
	Hilti HIT-HY 170: Universal Adhesive Anchoring System Discover the Hilti HIT-HY 170, a high-performance universal adhesive anchoring system designed for reliable and versatile fixing in concrete and various masonry types. Learn about its applications, safety, and technical specifications.