RP362M WiFi Extender

Quick Start Guide

Package Contents

The following items are included in the box:

RP362M
Quick Start Guide
Power adapter (varies by region)

If any of these items are damaged or missing, please contact your service provider immediately.

Chapter 1: Introduction

Overview

The RP362M is designed to enhance the connectivity between your WiFi router and wireless client device while increasing the coverage of your existing WiFi network. With its simple setup, this high-speed 802.11ac extender works seamlessly with most routers.

Features

Easy Setup: WPS button setup or web browser configuration

Wireless Features

Supports 11ac WiFi: 802.11ac is backwards compatible with 802.11a/b/g/n
WPS Support: WPS (WiFi Protected Setup) simplifies the process of connecting any device to the wireless network by using the push button on the device.
Security Support: WPA2, WPA, and WPA+WPA2 mixed mode are supported for advanced encryption of all WiFi data.

Chapter 2: Basic Setup

This chapter provides details on how to set up the RP362M.

Front Panel

1. Power LED (Green): Solid Green - Power on; Off - No power; Blinking - Power LED will blink during start up.
2. WiFi LED (Green/Blue/Red): Solid Green - Backhaul connection is available and the signal strength is good; Off - Backhaul connection is not established; Solid Red - Backhaul connection is available and the signal strength is poor. Note: If the WiFi LED is red, you need to install the extender in a location closer to your router. Slow Blinking Blue - WPS is pairing. When WPS button is pressed, the LED will blink for 2 minutes; Solid Blue - WPS failure. The LED will stay on for 10 seconds and then turn off; Fast Blinking Blue - WPS success. The LED will blink quickly for 10 seconds, then turn off.
3. LAN LED (Green): Solid Green - Ethernet cable connected; Off - Ethernet cable not connected.

Side Panel

1. LAN port: Connect to a PC or other Ethernet device using a standard Ethernet cable.
2. Reset Button: This button is recessed; a pin or paper clip can be used to press it. The button can be used while the unit is powered and the Power LED is Green. Press and hold over 5 seconds to reset to manufacturer default values and reboot. Press and hold over 2 seconds and less than 5 seconds to reboot.
3. Power Jack: Connect the power adapter to the device.
4. WPS Button: Push the WPS button on the device and on your other WiFi device to perform WPS function that easily creates an encryption-secured WiFi connection automatically. Press and hold over 2 seconds to enter WPS mode to connect to a WiFi router. After connected to a WiFi router, the RP362M will perform WPS with the client devices when pressed and held more than 2 seconds.

Setup Using WPS

Make sure the WiFi router is on and working properly.
Plug the RP362M into a wall outlet near the WiFi router during setup.
Wait for the Power LED to become solid green; the RP362M is now ready for setup.
Push the WPS button on the WiFi router to enable WPS mode. The LED on the router will blink and WPS will stay active for 2 minutes.
Push and hold the WPS button on the RP362M for more than 2 seconds. The WPS LED on the device will start blinking for 2 minutes. The RP362M will automatically connect to the WiFi router.
The connection between the RP362M and WiFi router is complete after the WiFi LED turns solid green and remains on.
Now move the RP362M to a suitable location. Place the extender 1 or 2 rooms away from your existing WiFi router. Check the WiFi LED color on the RP362M and make sure it's not solid red.
After setup, the RP362M extends the network using the same SSID and password from your current WiFi router.

Note! If the WiFi LED is solid red, move the RP362M closer to the WiFi router.

Setup Using Web Browser

Make sure the WiFi router is on and working properly.
Plug the RP362M into a wall outlet near the WiFi router during setup.
Wait for the Power LED to become solid green; the RP362M is now ready for setup.
Connect an Ethernet cable to the RP362M and your PC.
Launch the browser and enter http://192.168.0.1 in the Address box.
You will be prompted for a username and password. Use the default values: 'admin' for the username, and 'WPS PIN' for the password.
Choose the Wizard page. The RP362M will start to search for existing WiFi 5GHz networks. If RP362M doesn't connect to a WiFi router, it will redirect to the Wizard page when the user logs in next time.
Select your desired SSID for the RP362M to connect. A 5GHz channel is recommended to be used for this connection (Ch. 36-165). Click Next.
The Security Settings screen will be shown automatically if your WiFi router is using encryption. Enter your WiFi router security key. Click Next.
The Extended Network Settings screen will be prompted automatically if the security is enabled. It is recommended to click "Clone Settings" to use your existing WiFi router SSID and password, or you can enter a new SSID and password for the extender network. Click Next.
Wait until the RP362M connects to the router and the browser moves to the System Status screen.
Now move the RP362M to a suitable location. Place the extender 1 or 2 rooms away from your existing WiFi router. Check the WiFi LED color on the RP362M and make sure it's not solid red.
After setup, the RP362M extends the network using the same SSID and password from your current WiFi router.

Note! If the WiFi LED is solid red, move the RP362M closer to the WiFi router.

Appendix A: Regulatory

FCC Statement

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

	RP324 WiFi Extender Quick Start Guide A quick start guide for the RP324 WiFi Extender, detailing setup procedures using WPS or a web browser, package contents, front and side panel features, and regulatory information.
	Sercomm RP582B 802.11ax Router/Extender User Manual User manual for the Sercomm RP582B 802.11ax router/extender, providing setup instructions, LED behavior explanations, and important regulatory compliance information from FCC and Industry Canada.
	Sercomm RP582B 802.11ax Router/Extender User Manual User manual for the Sercomm RP582B 802.11ax router and extender, detailing setup, LED behavior, device description, and regulatory compliance information from FCC and ISED.
	FCC Test Report for Sercomm DOCSIS 3.1 WiFi 6 Gateway DG4244 Official FCC test report for the Sercomm DOCSIS 3.1 WiFi 6 Gateway (Model DG4244), detailing compliance testing for WLAN operations under FCC Part 15, Subpart E. Includes test results, product specifications, and applicable standards.
	Sercomm RP131CBRS-P LTE Video Bridge Adapter - Product Overview and Specifications Learn about the Sercomm RP131CBRS-P, an LTE CPE Video Bridge Adapter for CBRS band. Features include NAT mode, PSE function, and LED status indicators. Includes FCC compliance information and support details.
	DG4244 DOCSIS 3.1 WiFi 6 Gateway Basic User Guide This guide provides essential information for setting up and using the DG4244 DOCSIS 3.1 PacketCable 1.5 WiFi 6 Gateway, including safety notices, installation instructions, and an overview of device features and settings.
	Sercomm Corporation FCC Attestation Statements for P27-TMOG4SE FCC Attestation Statements filed by Sercomm Corporation for the P27-TMOG4SE equipment, confirming it is not 'covered' equipment and the applicant is not on the Covered List.
	Sercomm Speedport Plus Installation Manual This manual provides step-by-step instructions for installing and setting up the Sercomm Speedport Plus Wi-Fi router for internet and Magio TV services.