Inateck BK2007 Bluetooth Keyboard Case

Product Diagram

The product features a magnetic strip, Caps Lock indicator, Bluetooth indicator, battery indicator, charging port, and various shortcut keys.

1. Bluetooth Pairing

First-time use: Attaching the protective case to the magnetic strip turns on the keyboard and enters pairing mode. For subsequent uses, press fn + del to enter pairing mode. The Bluetooth indicator will blink.

On your iPad: Go to Settings > Bluetooth > On. "Inateck BK2007" will appear under "Other Devices". Tap it to pair. The Bluetooth indicator will remain solid upon successful connection.

Fix Bluetooth Pairing Problems

1. Go to Settings > Bluetooth, find "Inateck BK2007" in My Devices, tap the info button (i), and select "Forget This Device". Delete any multiple pairing records for the keyboard.
2. Hold esc + ⊚ (where ⊚ represents the Command key) simultaneously for 3 seconds. The three indicators will blink three times, indicating a factory reset.
3. Re-pair the Inateck BK2007 with your iPad.

2. Shortcut Keys

• esc: Undo
• Brightness -: Decrease brightness
• Brightness +: Increase brightness
• Q: Search
• Screenshot: Take a screenshot
• Switch keyboard layout: Switch keyboard layout
• Last track: ⊚ + ←
• Play/Pause: ▷II
• Next track: ⊚ + →
• Mute: ⊚ + ↓
• Volume -: ⊚ + ←
• Volume +: ⊚ + →
• Lock: ⊚ + Control + Q
• del: Delete

3. LED Indicator

4. Restore Factory Defaults

Hold esc + ⊚ simultaneously for 3 seconds. The three indicators will blink three times upon completion.

5. Check Battery Level

Hold fn + ⊚ simultaneously. Check the battery level based on the blinking frequency of the red battery indicator:

• 0-25%: 1 blink
• 25%-50%: 2 blinks
• 50%-75%: 3 blinks
• 75%-100%: 4 blinks

6. Charging

When the battery level is below 20%, the red battery indicator will blink. Use the included USB cable to recharge the keyboard. The recommended charging voltage and current are 5V and 200mA, respectively. The keyboard will be fully charged in approximately 2 hours. The red battery indicator stays solid while charging, and the green indicator stays solid when fully charged.

7. Sleep Mode

If the BK2007 is left idle for 30 minutes, it enters sleep mode, and the Bluetooth connection is disrupted. The connection can be re-established by pressing any key.

8. Product Specification

• Bluetooth Range: 10m
• Charging Time: About 2h
• Continuous Working Time: About 90h
• Operating Temperature: -10°C to 55°C
• Bluetooth Frequency Range: 2402-2480MHz
• Actuation Force: 60 ± 10g
• Battery Capacity: 250mAh

9. Packing List

• BK2007 * 1
• Charging Cable * 1
• Instruction Manual * 1

FCC Note

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. The device has been evaluated to meet general RF exposure requirement and complies with FCC's RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co-located or conjunction with any other antenna or transmitter.

EU Declaration of Conformity

Inateck Co., Ltd. hereby declares that this device complies with the Directive 2014/53/EU. A copy of the Declaration of Conformity can be accessed from https://www.inateck.de/pages/euro-compliance.

Service Center

Europe

F&M Technology GmbH
Tel: +49 341 5199 8410 (Working day 8 AM - 4 PM CET)
Fax: +49 341 5199 8413
Address: Fraunhoferstraße 7, 04178 Leipzig, Deutschland

North America

Inateck Technology Inc.
Tel: +1 (909) 698 7018 (Working day 9 AM - 5PM PST)
Address: 2078 Francis St., Unit 14-02, Ontario, CA 91761, USA

Japan

Inateck 株式会社
電話番号: +81 06 7500 3304
〒547-0014 大阪府大阪市平野区長吉川辺3丁目10番11号

UK REP

Inateck Technology (UK) Ltd.
95 High Street, Office B, Great Missenden, United Kingdom, HP16 0AL
Tel: +44 20 3239 9869

Manufacturer

Shenzhen Inateck Technology Co., Ltd.
Address: Suite 2507, Block 11 in Tian An Cloud Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China
深圳市理诚科技有限公司
广东省深圳市龙岗区坂田街道天安云谷2期11栋2507
电话:0755-23484029

Made in China