Commercial Electric 13-inch LED Interior Edge-Lit Adjustable Color Flush Mounts - Use and Care Guide

This guide provides instructions for the safe installation, use, and care of your Commercial Electric 13-inch LED Interior Edge-Lit Adjustable Color Flush Mounts. Please read all instructions before beginning assembly and installation.

Safety Information

WARNING: Carefully read and understand all information in this manual before starting installation. Failure to do so could result in electric shock, fire, or other serious injury.

WARNING: Ensure electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.

NOTICE: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment causes harmful interference to radio or television reception, try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; Consult the dealer or an experienced radio/TV technician.

Warranty

What is Covered

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer's only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer's discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling.

What is Not Covered

This warranty shall not apply to any product that is found to have been improperly installed, setup, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.

The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product.

Contact the Customer Service Team at 1-877-527-0313 or visit HOMEDEPOT.COM.

Pre-Installation

Planning Installation

Read all instructions before assembly. Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.

NOTE: Keep your receipt and these instructions for proof of purchase.

Tools Required

Tools needed for installation include: Wire Strippers, Safety Goggles, Ladder, Gloves, Flathead Screwdriver, Phillips Screwdriver, Electrical Tape, and Wire Cutters/Pliers.

Hardware Included (for each flushmount)

The following hardware is included:

AA - Mounting Bracket (1)
BB - Outlet Box Screw (15 mm long) (2)
CC - Ground Screw (1)
DD - Wire Connector (3)
EE - Locking Screw (9 mm long) (1)

Package Contents (for each flushmount)

The package contains:

A - Fixture (1)
B - Hook (1)
C - Locking Hole (1)
D - Fixture Ring (1)

Installation

1. Attaching the mounting bracket to the outlet box

Place the mounting bracket (AA) over the outlet box (sold separately) so the interior oval holes on the mounting bracket (AA) align with the screw holes on the outlet box. Screw the outlet box screws (BB) through the interior oval holes on the mounting bracket (AA) into the screw holes on the outlet box.

2. Connecting the electrical wires

Hang the hook (B) onto the mounting bracket (AA). Wrap the ground wire from the fixture (A) around the ground screw (CC) on the mounting bracket (AA). Use a wire connector (DD) to connect the end of the ground wire from the fixture (A) to the ground wire from the outlet box. Use a wire connector (DD) to connect the white wire from the fixture (A) to the white wire (neutral wire) from the outlet box. Use a wire connector (DD) to connect the black wire from the fixture (A) to the black wire (live wire) from the outlet box. Wrap the three wire connections with electrical tape for a more secure connection. Position the wires inside the outlet box.

3. Securing the fixture to the ceiling

Raise the fixture (A) until it is flush with the ceiling. Align the locking hole (C) with the hole on the mounting bracket (AA). Use your hand to screw the locking screw (EE) into the locking hole (C).

4. Selecting the CCT option

Choose your correlated color temperature (CCT) from the three options: 3000K soft white, 4000K bright white, or 5000K daylight. Use your hand to move the CCT switch side-to-side on the fixture (A) to make your selection.

5. Securing the fixture ring

Hold the fixture ring (D) so the arrow label on the fixture ring (D) is pointing up. Align the arrow on the fixture ring (D) with the arrow on the fixture (A) so the arrows point to each other. Place the fixture ring (D) over the fixture (A). Turn the fixture ring (D) clockwise until the fixture ring (D) locks into place (just a few inches). Once the fixture ring (D) is installed, remove the arrow label on the fixture ring (D).

WARNING: If not locked in place, the fixture ring (D) may fall and cause serious injury.

Care and Cleaning

Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box. Clean the fixture with a soft, dry cloth. Do not use any cleaners with chemicals, solvents, or harsh abrasives.

Troubleshooting

Problem	Possible Cause	Solution
The fixture will not light.	The power is off.	Ensure the power supply is On.
	The circuit breaker is off.	Ensure the circuit breaker is in the On position.
The fuse blows or the circuit breaker trips when the light is turned on.	The wires are crossed or the power wire is grounding out.	Check the wire connections. Contact a qualified electrician or call the Customer Service Team at 1-877-527-0313.

Commercial Electric Customer Service

Questions, problems, missing parts? Before returning to the store, call Commercial Electric Customer Service:

8 a.m. - 7 p.m., EST, Monday - Friday

9 a.m. - 6 p.m., EST, Saturday

1-877-527-0313

HOMEDEPOT.COM

Retain this manual for future use.

	Commercial Electric 7.5-inch LED Color Changing Recess/Surface Mount Fixture with Night Light - Use and Care Guide This guide provides detailed instructions for installing, using, and maintaining the Commercial Electric 7.5-inch LED Color Changing Recess or Surface Mount Fixture with Night Light. Includes troubleshooting tips, safety warnings, and warranty information.
	Commercial Electric 13-inch LED Colour Changing Flush Mount Use and Care Guide This guide provides detailed instructions for the Commercial Electric 13-inch LED Colour Changing Flush Mount (Models FM0180409-12, FM0180409-13), covering installation, safety precautions, maintenance, and troubleshooting. Learn how to safely install and care for your new lighting fixture.
	Commercial Electric Sebastian LED Decorative Ceiling Light - Use and Care Guide This guide provides detailed instructions for the Commercial Electric Sebastian LED Decorative Ceiling Light, covering installation, operation, maintenance, and troubleshooting. Learn about its features like CCT selection and dimmability. Model numbers include FP1236WHW48LF4H and FP1236DGR48LF4H.
	Commercial Electric LED Slim Color Changing Recessed Kit with Night Light - Use and Care Guide This guide provides detailed instructions for the installation, use, and care of the Commercial Electric LED Slim Color Changing Recessed Kit with Night Light. Learn about safety precautions, installation steps, features, and troubleshooting.
	4ft x 8in LED Flush Mount Ceiling Light - Commercial Electric Product Specifications Detailed specifications for the Commercial Electric 4ft x 8in LED Flush Mount Ceiling Light, including model numbers, dimensions, power, color temperature, dimming capabilities, packaging information, and included components. Suitable for damp locations.
	Commercial Electric S5.5WPK/MM/BZ LED Wall Mount Pack Use and Care Guide Comprehensive use and care guide for the Commercial Electric S5.5WPK/MM/BZ LED Wall Mount Pack, covering installation, operation, maintenance, and troubleshooting. Includes safety warnings and product specifications.
	Commercial Electric 4 FT Moroccan Series LED Linear Ceiling Light - Use and Care Guide This guide provides instructions for the use, care, installation, and troubleshooting of the Commercial Electric 4 FT Moroccan Series Color Selectable LED Linear Decorative Ceiling Light.
	Commercial Electric 4ft x 10in LED Flush Mount Ceiling Light Specifications Product specifications for the Commercial Electric 4ft x 10in LED Flush Mount Ceiling Light, including model numbers, dimensions, power, color temperature, dimming compatibility, and included components.