Commercial Electric LED Wall Mount Pack

Product Specifications

• 120/277 VAC, 50/60Hz, 40 Watts
• Not for use with dimmers
• Suitable for wet locations

Dusk to Dawn Operation

The light turns on at dusk and remains on until dawn. It stays off during the day until dusk. A convenience cover (HH) is provided to block light and bypass the sensor, allowing continuous operation controlled by a wall switch or master photocell.

Safety Information

Read Before Installation

Follow all safeguards and normal safety precautions for electrical devices to reduce the risk of fire, electric shock, and personal injury.

WARNING: RISK OF SHOCK

Household electric current can cause shock or injury. Always:

• Turn OFF power at the fuse or circuit breaker box before installation.
• Ground the fixture to prevent electric shock and ensure reliable starting.
• Double-check all connections for tightness.
• Wear rubber-soled shoes and use a sturdy ladder.

This fixture is designed for use in a circuit protected by a fuse or circuit breaker and must be installed according to local electrical codes. Consult a qualified electrician if unsure.

WARNING: RISK OF CUTS

Some metal parts may have sharp edges. Wear gloves when handling parts to prevent cuts and scrapes.

Account for small parts and destroy packaging material as it may be hazardous to children.

General Warnings

⚠️ WARNING: These products may represent a possible shock or fire hazard if improperly installed or attached. Install in accordance with the owner's manual, current electrical codes, and the National Electric Code (NEC). Properly ground electrical enclosure. Use only UL or IEC approved wire.

⚠️ CAUTION: To avoid risk of fire, explosion, or electrical shock, this product must be installed, inspected, and maintained by a qualified electrician only, in accordance with all applicable electrical codes. Ensure electrical power is OFF before and during installation and maintenance.

⚠️ CAUTION: This product must be installed in accordance with the applicable installation code by a person familiar with the product's construction, operation, and associated hazards.

SAVE THESE INSTRUCTIONS

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. CAN ICES-005 (B).

ISED Statement

This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Responsible Party: Feit Electric Company, 4901 Gregg Road, Pico Rivera, CA 90660, USA, 562-463-2852

Unique Identifier: S5.5WPK/MM/BZ

Limited Warranty

This product is warranted to be free from defects in workmanship and materials for up to 5 years from date of purchase. If it fails to do so, please contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.ca.

Pre-Installation

NOTE: Hardware not shown to actual size.

Tools Required

• [Screwdriver Icon] Phillips screwdriver
• [Hammer Icon] Hammer

Package Contents

Installation

1. Turn the power OFF at the wall switch and fuse box or the circuit breaker.
2. Remove the Fixture Lens (CC) from the Wall Pack Fixture (AA) by unscrewing the four Lens Screws (EE).
3. Remove the Reflector (BB) from the Wall Pack Fixture (AA) by unscrewing the two Reflector Screws (DD).
4. Use a screwdriver and hammer (not provided) to knock out the screw holes on the Wall Pack Fixture (AA) according to the J-box being used.
5. Using Wire Connectors (GG), connect the 3 wires coming from the Wall Pack Fixture (AA) to the Junction Box Wires: Black - Line Voltage, White - Neutral, Yellow-Green or Green - Ground.
6. Feed the junction box wires and fixture wires into the Junction Box. Mount the Wall Pack Fixture (AA) to the J-Box using the two J-Box Screws (FF) through the knockout screw holes.
7. Re-assemble the Reflector (BB) to the Wall Pack Fixture (AA) by screwing in the two Reflector Screws (DD).
8. Re-assemble the Fixture Lens (CC) to the Wall Pack Fixture (AA) by screwing in the four Lens Screws (EE).
9. (Optional) To bypass the Dust-To-Dawn Sensor to operate the Fixture by wall switch only, simply place the Dust-To-Dawn Sensor Cover (HH) over the Sensor.
10. Turn the power ON at the wall switch, circuit breaker or fuse box.
11. Once the fixture is tightly secured to J-Box, apply silicone sealant around the base of the fixture to prevent moisture from reaching the connections.

Operation

Lumen Switch

Select the brightness: 1500, 3000 or 4000 lumens.

CCT Switch

Select the color temperature:

• 3K (3000K) – Soft White
• 3.5K (3500K) – Neutral White
• 4K (4000K) – Bright White
• 5K (5000K) – Daylight
• 6.5K (6500K) – Daylight Deluxe

D2D/MOT Switch

• D2D (Dusk to Dawn): Motion detection is disabled. The light will remain off during the day and automatically turn on at dusk. A Dust-To-Dawn Sensor Cover (HH) is provided to block light and bypass the sensor, allowing continuous operation controlled by a wall switch or master photocell.
• MOT (Motion Sensor): Motion sensor is activated. The light will turn on for 10 minutes when motion is detected. During this time, brightness will be at 100% and will drop to 30% of the selected lumen if no motion is detected.

NOTE: There will be a warmup time for about 8 seconds when first powered up. Brightness will be at 100% and will then drop to 30% after the warmup time. Brightness will go to 100% once motion is detected.

Motion Sensor Coverage

The 180-degree coverage of the motion sensor is measured side-to-side. The sensor will detect motion across the field of view. The motion sensor maximum detection range is up to 35 ft.

Care & Maintenance

Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner and soft cloth. Ensure the power is turned off before cleaning. Do not spray cleaner directly onto any part of the fixture or LEDs.

Troubleshooting