Sealey - Leading Professional Tool & Workshop Equipment Supplier
Instruction Manual for SEALEY models including: SA825 Portable Manual Air Hose Reel, SA825, Portable Manual Air Hose Reel, Manual Air Hose Reel, Air Hose Reel, Hose Reel
6. MAINTENANCE WARNING! Before attempting maintenance or inspection, disconnect the hose. To ensure reliable operation, clean the hose and casing regularly.
Sealey SA825 20m Portable Manual Air Hose Reel 6mm ID » Product
20m Portable Manual Air Hose Reel 6mm ID - Anvil Tool
File Info : application/pdf, 2 Pages, 313.91KB
DocumentDocumentPORTABLE MANUAL AIR HOSE REEL, 20M, Ø6MM ID, 300PSI MODEL NO: SA825 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. Refer to instructions 1. SAFETY Wear eye protection 9 Familiarise yourself with the application and limitations of the hose reel, as well as the specific hazards. 9 Maintain the hose reel in good condition (use an authorised service agent). 9 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 8 DO NOT place inside a spray booth/oven. 9 Ensure there is adequate lighting. WARNING! Ensure maximum air pressure is not exceeded (300psi). 9 Keep extended air hose away from heat, oil and sharp edges. 9 Check hose for wear before each use and ensure all connections are secure. 9 Keep the unwound hose away from wet, damp, oily surfaces to avoid debris accumulation in between the hose reel. WARNING! Always wear approved eye protection when operating the air hose reel. 9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip footwear. 9 Keep children and unauthorised persons away from the working area. 8 DO NOT operate the hose reel if any parts are damaged or missing as this may cause failure and/or personal injury. 8 DO NOT use the hose reel for any purpose other than that for which it is designed. 8 DO NOT pull the hose from the supply. 8 DO NOT operate the hose reel when you are tired or under the influence of alcohol, drugs or intoxicating medication. 8 DO NOT direct air from the air hose at yourself or others. WARNING! Ensure the hose is disconnected from the supply when not in use or carrying out any maintenance or assembly. 8 DO NOT position the hose in direct sunlight or in areas of extreme heat or cold. 2. iINTRODUCTION Lightweight, floor standing hose reel with built in carry handle for easy transportation. Features high grade TPR (Thermoplastic Rubber) inner tube and a reinforced PVC outer coating, which remains flexible in low temperatures. Silicone-free for use in the bodyshop. Fitted with quick connectors and supplied with a 1.9m inlet hose to connect the hose reel to a compressor. Drum is manufactured from impact resistant plastic. 3. sSPECIFICATION Model No:............................................................ SA825 Hose Size (ID/OD): .........................................Ø6/11mm Hose Type: .............................. Reinforced Braided PVC Inlet Size: .............................................Quick Connector Length:.................................................................... 20m Maximum Pressure: ............................................ 300psi Nett Weight: .......................................................... 4.2kg Outlet Size: ..........................................Quick Connector 4. ASSEMBLY 4.1. 4.1.1. REMOVE ALL ITEMS FROM THE PACKAGING. Connect quick connector to side of hose reel (fig.1). 5. OPERATION 5.1. 8 5.2. 5.2.1. 5.3. 5.3.1. CONNECT TO AN AIR LINE DO NOT connect directly to an air tool, connect a leader hose to the tool first and then connect the leader hose to the air hose reel. EXTENDING THE HOSE Pull the hose out slowly to the length required and stop. RETRACTING THE HOSE Rewind the hose manually. fig.1 © Jack Sealey Limited Original Language Version SA825 Issue:2 (2) 12/03/24 6. MAINTENANCE 6.1. 6.1.1. WARNING! Before attempting maintenance or inspection, disconnect the hose. To ensure reliable operation, clean the hose and casing regularly. DO NOT spray or wet the product, but clean with a damp cloth and warm water. DO NOT use solvents or detergents, as these may permanently damage the item. The hose reel does not require special maintenance as it is lubricated for life. Replacement of the supply hose should be carried out by skilled personnel only, consult your nearest authorised service agent. STORAGE Before storing the air hose, ensure it is clean and dry. Store it in a dark, safe, dry, childproof location, where the temperature will remain reasonably stable. ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. REGISTER YOUR PURCHASE HERE Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk www.sealey.co.uk © Jack Sealey Limited Original Language Version SA825 Issue:2 (2) 12/03/24