Welcome
Thank you for purchasing a STREAMLINE® Water Filtration System. The 600GPD filtration system is very efficient at purifying water and is simple to install and maintain. It is the installer's responsibility to ensure that this appliance is plumbed in accordance with the local authority's by-law regulations. Your water filtration system has been assembled and tested to ensure that there are no leaks.
Installation Instructions
Set Up
- Unscrew the three vertical filter bowls and remove the wrapping from the cartridges. Reassemble the bowls. A filter spanner is included in the kit for loosening the filter bowls. Do not overtighten the filter bowls when reassembling.
- Connect a water supply hose to the fitting marked 'Mains inlet connection'. A hose lock type connection kit can be purchased to simplify the hose connection (Part no. KIT01300 Brass fittings kit or KIT01301 Nylon fittings kit).
- Cut and connect a suitable length of 1/2 inch tube to the waste water connection marked 'DRAIN'. This tube is the waste water tube and must discharge into the nearest drain.
- Cut and connect a suitable length of 1/2 inch tube and attach it to the connection marked 'FAUCET'. This will discharge pure water into the storage tank.
- Identify the small R.O. Plug, which is packaged in the R.O. Membrane bag. Lubricate the two O-rings and insert this plug into the notched side of the centre white tube of the membrane.
Diagram Description (Figure 1): Shows the water filtration system with three vertical filter housings connected to a 'Mains Inlet Connection' point.
- Remove the cap on the left-hand side of the front R.O. Housing. Insert the blue R.O. membrane with the large black rubber seal towards the open end of the housing. Screw the end cap of the membrane housing in place and refit the inlet tube.
- Remove the right-hand cap of the second R.O. Housing and repeat the process.
- Temporarily remove the tube on the inlet connection of the R.O. Filter housing. Turn the water supply on, allowing the water to flush through the first three vertical filters for 2-3 minutes, until all visible impurities have disappeared.
- Turn the water supply off and reconnect the tube.
- Open the flushing valve by turning the grip parallel to the tube.
- Turn the water supply on and test the system for leaks.
- Allow the system to run for 5 minutes before closing the flushing valve. The TDS reading will improve over 24-48 hours.
Diagram Description (Figure 2): Illustrates the connections for the reverse osmosis system, indicating the 'R.O. Inlet Connection', 'Drain' for waste water, and 'FAUCET' for pure water output. It also shows a tube temporarily removed from the inlet connection.
Diagram Description (Figure 3): Depicts the 'R.O. Plug' and indicates the location ('Fit Plug In Here') on the notched side of the center white tube of the R.O. membrane.
Diagram Description (Figure 4): Displays the front and rear sections of the Reverse Osmosis system, highlighting the 'Flushing Valve' and showing the correct orientation for inserting the R.O. membrane into the housing.
Maintenance
- Open the flushing valve and allow the water to flush the membranes and run to drain for 10 minutes once a week. Once complete, close the valve completely by turning the grip 90 degrees to the tube.
- Replace the three vertical pre-filters every 3 months, or more frequently in very hard water areas (300ppm+).
Optional Extras
- Pre R.O. Softening filter, for use in hard water areas to bring TDS readings down and enhance R.O. Membrane life. (Part no. FH1K plus fittings.)
- Male Hose lock type fittings kit. (Part no. KIT01600 Brass fittings kit or KIT01601 Nylon fittings kit.)
- Post R.O. resin filter to produce 000ppm from the 600GPD system. (Part no. FH1D plus fittings.)
STREAMLINE® Warranty
The warranty on all STREAMLINE® Machines and Equipment is for 1 year (12 months) from the recorded date of purchase.
Warranty Exclusions: This warranty excludes normal maintenance items, including but not limited to hoses, filters, O-rings, diaphragms, valves, gaskets, carbon brushes, and damage to motors and other components resulting from failure to replace normal maintenance items. This list is not exhaustive.
If STREAMLINE® receives notice of defects during the warranty period, STREAMLINE® will, at its discretion, repair or replace components that prove to be defective. Replacement parts will only be supplied under warranty upon inspection and approval of the defective parts by STREAMLINE®.
Should replacement parts be necessary before inspection, they will be charged at current prices, and credit will only be issued upon subsequent inspection and warranty approval by STREAMLINE®.
The customer is responsible for the cost of returning the defective part. If the warranty is approved, STREAMLINE® will cover the cost of the repaired or replacement part.
This warranty excludes the following conditions and circumstances, which are at the discretion of STREAMLINE®:
- Wear and tear, misuse, abuse, improper maintenance, frost damage.
- Use of chemicals other than those supplied or approved by STREAMLINE®.
- Improper installation or repair, unauthorized modification.
- Incidental or consequential costs, loss or damage, service, labour, or third-party charges.
- The cost of returning defective parts to STREAMLINE®.
This warranty constitutes the exclusive remedy for any purchaser of a STREAMLINE® unit and is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for use, to the fullest extent permitted by law. In no event shall any implied warranty of merchantability or fitness for use exceed the term of the applicable warranty stated above, and STREAMLINE® shall have no other obligation or liability.
Important: Unfortunately, these rights cannot be transferred to a third party.
Why STREAMLINE®?
Flexibility
- STREAMLINE® systems can be built according to customers' exact requirements.
- For non-standard systems, user needs or specifications are listened to and turned into reality.
Quality
- While price is important, quality is remembered long after price is forgotten.
- STREAMLINE® insists on sourcing brand-name products from around the world, only of reputable quality, and brings them together under the STREAMLINE® name.
- All STREAMLINE® products carry a full one-year warranty, according to the manufacturers' standard terms and conditions of sale.
Service
- STREAMLINE® has an in-house technical helpline able to answer most questions relating to the capabilities and functionalities of all STREAMLINE® products.
- If STREAMLINE® gets it wrong, they will put it right. If a wrong item is sent, they will immediately attend to sending the correct item and arrange a collection of the wrong item without any quibbles.
- STREAMLINE® is backed by a comprehensive range with massive stocks, providing customers with a 'one stop shop' for all their requirements.
Contact Information
STREAMLINE
Hamilton House, 8 Fairfax Road,
Heathfield Industrial Estate,
Newton Abbot
Devon, TQ12 6UD
United Kingdom
Telephone: +44 (0) 1626 830 830
Email: sales@streamline.systems
Visit: www.streamline.systems
