R. STAHL Miniature Circuit Breaker 8530/1-MCB-STA103N-C63-100-4
Art. No. 293882
Components for system solutions
The R. STAHL 8530 series miniature circuit breakers are overcurrent devices designed for system solutions. They offer good current limiting for short circuits and a high switching capacity of 10, 15, or 25 kA, resulting in low load on cables and high selectivity for upstream fuses.
These components feature a modular design and are available in 1- to 4-pole versions for rated currents of 0.5-63 A. The maximum installation capacity is 4.5 subunits.
Key Features:
- Isolation function in accordance with EN60947-2
- Energy limitation class 3
- Simple replacement or expansion of systems due to modular design
- Easy installation: snaps onto the mounting rail in Ex e enclosures
- Non-adjustable thermal and magnetic releases
- Ergonomically shaped operating lever for safe switching
- Padlocks (Accessories) provide protection against being switched on during maintenance
Technical Data
Explosion Protection
| Application range (zones) | 1, 2 |
| Application range (Zone) note | For use in Zone 21/22 when protected by Ex tb/tc enclosure |
| IECEx gas certificate | IECEx FMG 19.0029U |
| IECEx gas explosion protection | Ex db eb IIC Gb |
| ATEX gas certificate | FM19ATEX0191U |
| ATEX gas explosion protection | II 2 G Ex db eb IIC Gb |
| Certificates | ATEX (FM), Brazil (ULB), China (CQST), IECEx (FM) |
| Declaration of conformity | Certificate of conformity (ATEX) |
Electrical Data
| Rated operational voltage AC | 230/400 V |
| Rated operational current | 63 A |
| Frequency | 50/60 Hz |
| Rated switching capacity | 10 kA |
| Electrical service life | 104 |
| Mechanical service life | 2 x 104 |
| 1st auxiliary function | Auxiliary contact 1 change-over contact |
| 1st auxiliary function for AC rated voltage | 230 V |
| 1st auxiliary function for rated current max. | 2 A |
| 2nd auxiliary function | without |
| 2nd auxiliary function voltage max. DC | - |
| Tripping characteristic | C |
| No. of poles | 3-pole + N |
Ambient Conditions
| Ambient temperature | -40 °C ... 70 °C |
| Ambient temperature (Fahrenheit) | -40 °F ... 158 °F |
| Ambient temperature note | Deviating ambient temperatures based on current certificates available on request |
Mechanical Data
| Degree of protection (IP) (IEC 60529) | IP2X |
| Enclosure material | Thermoplast |
| Connection cross section min. | 1.5 mm² |
| Connection cross-section max. | 25 mm² |
| Connection cross-section AWG min. | 16 AWG |
| Connection cross-section AWG max. | 4 AWG |
| Connection cross-section 2 min. | 1.5 mm² |
| Connection cross-section 2 max. | 10 mm² |
| Connection cross-section 2 AWG min. | 16 AWG |
| Connection cross-section 2 AWG max. | 8 AWG |
| Min. aux. cont. con. cr.-sect. | 0.5 mm² |
| Max. aux. cont. conn. cr.-sec. | 4 mm² |
| Min. aux. co. con. cr.-se. AWG | 18 (unece.unit.AWG) |
| Connection cross-section of auxiliary contact AWG max. | 14 (unece.unit.AWG) |
| Min. tightening torque | 2 N·m |
| Max. tightening torque | 3 N·m |
| Connection cross-section note | 2-conductor connection (upper and lower chamber at the same time): upper and lower chamber max. 16/10 mm² (A maximum difference of one cross section may be clamped between the upper and lower chamber.) The permitted combinations of connection cross-sections can be found in the operating instructions. |
Dimensions
| Width | 110 mm |
| Width, inches | 4.33 in |
| Length | 165 mm |
| Length in inches | 6.5 in |
| Mounting depth | 138.3 mm |
| Mounting depth in inches | 5.44 in |
| Weight | 1.8 kg |
| Weight (lbs) | 3.969 lb |
Mounting / Installation
| Tightening torque | 2-3 N·m |
| Tightening torque lbf·in | 17.7 to 26.6 lbf·in |
| Tightening torque auxiliary contact | 0.4–0.6 N·m |
| Tightening torque auxiliary contact lbf·in | 3.5 to 5.3 lbf·in |
Technical Drawings
Illustrations are subject to alterations.
Dimensional Drawings (All Dimensions in mm [inches])
Tripping Characteristic C
A graph shows tripping time in seconds and minutes against multiples of rated current for a tripping characteristic C. The curve indicates tripping times ranging from 0.01 seconds to over 120 seconds for currents from 0.1 times the rated current up to 10 times the rated current.
Accessories
4-way locking device
A lock-out/tag-out hasp for individually locking the component using up to four cylinder locks.
| Art. No. | 227232 |
Cylinder lock
For closing (bracket Ø 3)
| Art. No. | 107115 |
Fastening set
A fastening set for fastening the component on the mounting plate without a DIN rail.
| Art. No. | 276618 |
R. STAHL reserves the right to make alterations to the technical data, dimensions, weights, designs and products available without notice. The illustrations cannot be considered binding.
