Shenzhen Xinchen Zhilian Technology BS001 Bluetooth Speaker

Features and Specifications

• Main Device Parameters
• Output Power: 30W+20W
• Frequency Response: 65Hz-20KHz
• BT V5.0
• Driver: 4"*1+2"*2
• Power Supply: DC 5V 2A
• Distortion: <0.5%
• S/N: >65dB
• Battery Capacity: 7.4V 2200mAh
• Battery Play Time: 2-2.5 hours
• Battery Charging Time: 4-5 hours
• Product Size: L252*W152*H166mm
• Product Weight: 2350g

Package Contents

1. Speaker
2. User Manual
3. USB Charging cable

Charging the Speaker

Before using the speaker for the first time, charge it for at least 24 hours.

1. Plug the USB charging cable into the charging socket of the speaker. Plug the other end of the USB charging cable into an adapter. The red LED indicator on the speaker will light up and your speaker will start charging.
2. The red LED turns on to indicate that the unit is charging.
3. Once fully charged, the red LED turns off.

Pairing the Device

1. Place speaker within 30ft of the Bluetooth-enabled device.
2. Slide the ON/OFF button to ON. The white LED flashes 3 times slowly, then flashes quickly to indicate Bluetooth pairing mode.
3. Follow the instructions of your device to search for the speaker.
4. The white LED flashes when pairing is complete.

Basic Instructions

1. To turn the speaker on, press the ON/OFF button to ON.
2. The speaker beeps and a white LED flashes slowly.
3. The white LED stays on when playing music.
4. When the battery is low, the machine beeps "beep" at intervals of 1 minutes.

LED indicator

• (1) Charging: Red LED on (the speaker off)
• (2) Fully Charged: Red LED off
• (3) Pairing Mode: White LED flashes quickly
• (4) Connected: White LED on
• (5) Playing: White LED flashes slowly

Safety information

To reduce the risk of electric shock, do not attempt to disassemble the device.

Do not use this product in an aircraft or in a hospital.

Do not expose the device to direct sunlight, heat or flame. The device may become warm while charging.

• Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
• This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

Speaker button functions

A diagram shows the top of the speaker with numbered buttons and ports. The numbers correspond to the functions listed below.

1. Power On/Off: Toggle to turn the unit On/Off.
2. Last song: Press quickly for last song.
3. Volume up/down: Rotate the switch and adjust the volume.
4. Next song: Press quickly for next track.
5. 3.5mm audio input (line-in)
6. Bluetooth / AUX: Press the button to switch Bluetooth status and stereo state. Press and hold the button for Bluetooth free pairing.
7. LED Red/Blue
8. Play/Pause: When playing music, press the button to pause or play.
9. DC 5V 2A

FCC Warning

15.19 Labeling requirements.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

15.21 Information to user.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

15.105 Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement:

• This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
• This equipment should be installed and operated with minimum distance 5mm between the radiator and your body.