Hotone Pulze Mini BT Modeling Amplifier

Product Identification

Brand: Hotone

Product Name: Mini BT Modeling Amplifier

Model: Pulze Mini

Model Number: AP-5

HVIN: AP-5

Dimensions

Overall Width: 280.00 mm

Main Section Width: 140.00 mm

Height: 100.00 mm

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC ID: ZAHJSAP-5

IC Caution

Radio Standards Specification RSS-Gen, issue 5

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS (s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.

RF exposure statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes: Cet appareil ne doit pas causer d'interférences.

Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un fonctionnement indésirable de l'appareil.

Déclaration d'exposition RF: L'appareil a été évalué pour répondre aux exigences générales d'exposition aux RF. L'appareil peut être utilisé dans des conditions d'exposition portable sans restriction.

IC: 30142-AP5

Product Improvement and Disclaimers

In the interest of product improvement, the specifications and/or the content of products (including but not limited to appearances, packaging design, manual content, accessories, size, parameters and display screen), are subject to change without prior notice. Please check with local supplier for exact offers. Specifications and features (including but not limited to appearances, colors and size) may vary by model owing to environmental factors, and all images are illustrative.

In the interest of product improvement, specifications and/or product content (including but not limited to appearance, packaging design, manual content, accessories, size, specifications, display screen, etc.) are subject to change without prior notice. Please confirm product functions and specifications with your local dealer before purchasing. Product images and colors may differ slightly from the actual product due to photographic lighting errors and screen settings; please refer to the actual product.

Firmware Update Recommendation

We recommend updating to the latest firmware for the best possible experience.

Support

Visit www.hotone.com/support for the full manual and editor software.

Technical Requirements

Material: 157g coated paper

Size: 280*100mm (folded to 140*100mm)

Printing: Single-color printing

Finish: Matte lamination

Folding Line: This page faces up after folding.